{"title":"M2.5 x 8mm Screws","description":"\u003cp\u003eM2.5 x 8mm screws are a popular length for single-board computer builds: Raspberry Pi cases and stacked PoE or NVMe HATs over standoffs, plus radio belt clips and some laptop bottom covers. This page collects every M2.5 x 8mm screw we sell.\u003c\/p\u003e\u003cp\u003eFor a Raspberry Pi stack, add the board thickness to the part of the standoff thread you want to engage; if the screw bottoms out in a short standoff, drop to 6 mm. Brass and nylon standoffs both take the same M2.5 thread. Measure an old screw with calipers: the thread diameter gives the M number and the length gives the second figure. On a countersunk head the length is measured overall, head included; on a flat-bottomed head it is measured from under the head to the tip.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eRelated sizes:\u003c\/strong\u003e \u003ca href=\"\/collections\/m2-5-x-6mm-screws\"\u003eM2.5 x 6mm\u003c\/a\u003e · \u003ca href=\"\/collections\/m2-5-screws\"\u003eAll M2.5 screws\u003c\/a\u003e · \u003ca href=\"\/collections\/m3-screws\"\u003eM3 screws\u003c\/a\u003e\u003c\/p\u003e","products":[{"product_id":"m2-5-x-8mm-phillips-flat-head-screws-for-raspberry-pi-5-case-black-10-pack","title":"M2.5 x 8mm Phillips Flat Head Screws for Raspberry Pi 5 Case Black 10-Pack","description":"\u003ch2\u003eM2.5 x 8mm Phillips Flat Head Screws for Raspberry Pi 5 Case — Black, 10-Pack\u003c\/h2\u003e\n\u003cp\u003eTen M2.5 x 8mm Phillips flat head machine screws in black carbon steel, for re-assembling a Raspberry Pi 5 case or replacing lost case screws. M2.5 is the metric thread used for Raspberry Pi mounting holes and is easy to confuse with M2 or M3, which will either spin loose or refuse to thread.\u003c\/p\u003e\n\u003ch3\u003eHow to choose \/ measure\u003c\/h3\u003e\n\u003cp\u003eCheck the thread first: an M2.5 screw measures 2.5mm across the outside of the thread. Then measure the length of the threaded shank. If your original screw is 8mm and M2.5, this is the match; if the case uses a different length, pick that length instead so the screw does not bottom out.\u003c\/p\u003e\n\u003ch3\u003eCompatibility\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eRaspberry Pi 5 cases that use M2.5 x 8mm screws\u003c\/li\u003e\n\u003cli\u003eThird-party Raspberry Pi 5 cases with M2.5 mounting holes\u003c\/li\u003e\n\u003cli\u003eOther electronics that take an M2.5 x 8mm metric machine screw\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eSpecifications\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eThread size:\u003c\/strong\u003e M2.5 (metric)\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eLength:\u003c\/strong\u003e 8mm\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eHead:\u003c\/strong\u003e flat head\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eDrive:\u003c\/strong\u003e Phillips\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eMaterial:\u003c\/strong\u003e carbon steel\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eFinish:\u003c\/strong\u003e black\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003ePack quantity:\u003c\/strong\u003e 10 screws\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e\u003cstrong\u003eNote:\u003c\/strong\u003e not compatible with M2 or M3 threaded holes.\u003c\/p\u003e\u003c!-- tsw-fits:start --\u003e\u003cdiv class=\"tsw-fits\"\u003e\n\u003ch3\u003eFits these models\u003c\/h3\u003e\n\u003cp\u003eDevices whose service manuals, parts lists or manufacturer specifications call for an \u003cb\u003eM2.5 x 8mm\u003c\/b\u003e metric screw at the position shown. The thread and length match; check that the screw you are replacing also has a flat (countersunk) head.\u003c\/p\u003e\n\u003ctable class=\"tsw-fits-table\"\u003e\n\u003cthead\u003e\u003ctr\u003e\n\u003cth\u003eDevice \/ model\u003c\/th\u003e\n\u003cth\u003eWhere the screw goes\u003c\/th\u003e\n\u003cth\u003eSource\u003c\/th\u003e\n\u003c\/tr\u003e\u003c\/thead\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003eEurorack module\/rail mounting screw\u003c\/td\u003e\n\u003ctd\u003eSynthRacks sells M2.5 machine screws used to fix modules to Vector rails or Schroff rails with M2.5 nuts and threaded rails; 8mm length…\u003c\/td\u003e\n\u003ctd\u003esynthracks.com\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eRC servo horn retaining screw (Hitec\/Futaba style)\u003c\/td\u003e\n\u003ctd\u003eM2.5-0.45 x 8mm screw retains the servo horn\/arm\u003c\/td\u003e\n\u003ctd\u003eandymark.com\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eTurntable cartridge mounting kit (retail)\u003c\/td\u003e\n\u003ctd\u003e'2 x M2.5x3 mm Stainless Steel Screws. 2 x M2.5x6 mm Stainless Steel Screws. 2 x M2.5x8 mm...' cartridge\/tonearm mounting fixings\u003c\/td\u003e\n\u003ctd\u003evinylpro.co.uk\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003ePW-Sat2 CubeSat secondary structure and panels\u003c\/td\u003e\n\u003ctd\u003eM2.5 x 4mm solar panel brackets, M2.5 x 6mm sun sensor mount, M2.5 x 8mm secondary structure to X frames\u003c\/td\u003e\n\u003ctd\u003epw-sat.pl\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eTEKTELIC Kona Photon Gen-2 LoRaWAN gateway\u003c\/td\u003e\n\u003ctd\u003eM2.5 x 8mm screws for the SIM tray access-port cover\u003c\/td\u003e\n\u003ctd\u003etektelic.com\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003ePhono cartridge headshell mounting screws (Tonar universal set)\u003c\/td\u003e\n\u003ctd\u003eProduct spec explicitly lists 'Screw type: M2.5 non-magnetic hardware' for mounting nearly any phono cartridge to headshell\u003c\/td\u003e\n\u003ctd\u003esoundium.com\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eOyaide SCR-S phono cartridge screw set\u003c\/td\u003e\n\u003ctd\u003eProduct titled 'Oyaide M2.5 phono cartridge screw set w\/carbon graphite nylon washer', contains 6\/8\/10mm lengths, explicit M2.5 thread\u003c\/td\u003e\n\u003ctd\u003eaudiohobby.eu\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eOpenFlexure Delta Stage v1.1.0 motor mounts\u003c\/td\u003e\n\u003ctd\u003e8x M2.5x8mm screws secure the stepper motors\u003c\/td\u003e\n\u003ctd\u003ebuild.openflexure.org\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eHP 250R G9 \/ 256R G9\u003c\/td\u003e\n\u003ctd\u003echassis feet screws (4x)\u003c\/td\u003e\n\u003ctd\u003ekaas.hpcloud.hp.com\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eAcer Aspire 5332 \/ 5732Z\u003c\/td\u003e\n\u003ctd\u003eScrew List: SCREW M2.45D 8.0L K 5.5D 0.8T ZKNL\u003c\/td\u003e\n\u003ctd\u003emanualowl.com\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003cp\u003eFull list: \u003ca href=\"https:\/\/screwfitmentdatabase.com\/m2-5x8mm\"\u003eM2.5 x 8mm on Screw Fitment Database\u003c\/a\u003e\u003c\/p\u003e\n\u003ch4\u003eWhat does an M2.5 x 8mm screw fit?\u003c\/h4\u003e\n\u003cp\u003eService manuals and manufacturer specs list an M2.5 x 8mm screw in: Eurorack module\/rail mounting screw; RC servo horn retaining screw (Hitec\/Futaba style); Turntable cartridge mounting kit (retail); PW-Sat2 CubeSat secondary structure and panels; TEKTELIC Kona Photon Gen-2 LoRaWAN gateway. Match the head style of the screw you removed (this is a flat countersunk Phillips head).\u003c\/p\u003e\n\u003cscript type=\"application\/ld+json\"\u003e{\"@context\": \"https:\/\/schema.org\", \"@type\": \"FAQPage\", \"mainEntity\": [{\"@type\": \"Question\", \"name\": \"What does an M2.5 x 8mm screw fit?\", \"acceptedAnswer\": {\"@type\": \"Answer\", \"text\": \"Service manuals and manufacturer specs list an M2.5 x 8mm screw in: Eurorack module\/rail mounting screw; RC servo horn retaining screw (Hitec\/Futaba style); Turntable cartridge mounting kit (retail); PW-Sat2 CubeSat secondary structure and panels; TEKTELIC Kona Photon Gen-2 LoRaWAN gateway. Match the head style of the screw you removed (this is a flat countersunk Phillips head).\"}}]}\u003c\/script\u003e\n\u003c\/div\u003e\u003c!-- tsw-fits:end --\u003e","brand":"TechSpareWarehouse","offers":[{"title":"Default Title","offer_id":43433435168842,"sku":"RPI5-SCREW-M25X8-BLK-10PK","price":4.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0691\/7351\/0218\/files\/57_86335f47-a2a1-4dc0-8b23-8fce376a6eba.jpg?v=1774301917"},{"product_id":"m2-5-x-8mm-screws-for-raspberry-pi-5-case-and-poe-hat-10-pack-black","title":"M2.5 x 8mm Screws for Raspberry Pi 5 Case and PoE HAT 10-Pack Black","description":"\u003ch2\u003eM2.5 x 8mm Phillips Flat Head Screws for Raspberry Pi 5 Case and PoE HAT | Black | 10-Pack\u003c\/h2\u003e\u003cp\u003eM2.5 x 8mm screws that fit the M2.5 holes used by Raspberry Pi 4\/5 boards and many cases, including PoE HAT mounting.\u003c\/p\u003e\u003ch3\u003eWhy the Right Screw Matters\u003c\/h3\u003e\u003cp\u003eThese screws fit the M2.5 holes used by Raspberry Pi 4\/5 boards and many cases. The length you need depends on your case and on any HAT or standoff in the stack, so measure the original screw first: too short and it won't grip, too long and it can bottom out or touch the board.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003eStripped threads and damaged housings\u003c\/li\u003e\n\u003cli\u003eLoose components causing poor performance or failure\u003c\/li\u003e\n\u003cli\u003ePermanent damage to delicate assemblies\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eCompatibility\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eRaspberry Pi 5 official and third-party case assembly\u003c\/li\u003e\n\u003cli\u003eRaspberry Pi PoE HAT and PoE+ HAT mounting\u003c\/li\u003e\n\u003cli\u003eRaspberry Pi HAT stacking configurations\u003c\/li\u003e\n\u003cli\u003eGPIO header and board-to-board mounting\u003c\/li\u003e\n\u003cli\u003eGeneral Raspberry Pi M2.5 mounting applications\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eSpecifications\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eScrew Type:\u003c\/strong\u003e Machine Screw\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eThread Size:\u003c\/strong\u003e M2.5\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eLength:\u003c\/strong\u003e 8mm\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eHead Style:\u003c\/strong\u003e Phillips Flat Head (Low Profile)\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eDrive Style:\u003c\/strong\u003e Phillips\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eMaterial:\u003c\/strong\u003e Carbon Steel\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eFinish:\u003c\/strong\u003e Black Oxide\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eThread Standard:\u003c\/strong\u003e Metric\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003ePack Quantity:\u003c\/strong\u003e 10 Screws\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003e\u003cstrong\u003eImportant:\u003c\/strong\u003e M2.5 screws are not compatible with M2 or M3 threaded holes. Please verify your thread size before ordering.\u003c\/p\u003e\n\n\u003c!-- tsw-fits:start --\u003e\u003cdiv class=\"tsw-fits\"\u003e\n\u003ch3\u003eFits these models\u003c\/h3\u003e\n\u003cp\u003eDevices whose service manuals, parts lists or manufacturer specifications call for an \u003cb\u003eM2.5 x 8mm\u003c\/b\u003e metric screw at the position shown. The thread and length match; check that the screw you are replacing also has a flat (countersunk) head.\u003c\/p\u003e\n\u003ctable class=\"tsw-fits-table\"\u003e\n\u003cthead\u003e\u003ctr\u003e\n\u003cth\u003eDevice \/ model\u003c\/th\u003e\n\u003cth\u003eWhere the screw goes\u003c\/th\u003e\n\u003cth\u003eSource\u003c\/th\u003e\n\u003c\/tr\u003e\u003c\/thead\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003eEurorack module\/rail mounting screw\u003c\/td\u003e\n\u003ctd\u003eSynthRacks sells M2.5 machine screws used to fix modules to Vector rails or Schroff rails with M2.5 nuts and threaded rails; 8mm length…\u003c\/td\u003e\n\u003ctd\u003esynthracks.com\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eRC servo horn retaining screw (Hitec\/Futaba style)\u003c\/td\u003e\n\u003ctd\u003eM2.5-0.45 x 8mm screw retains the servo horn\/arm\u003c\/td\u003e\n\u003ctd\u003eandymark.com\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eTurntable cartridge mounting kit (retail)\u003c\/td\u003e\n\u003ctd\u003e'2 x M2.5x3 mm Stainless Steel Screws. 2 x M2.5x6 mm Stainless Steel Screws. 2 x M2.5x8 mm...' cartridge\/tonearm mounting fixings\u003c\/td\u003e\n\u003ctd\u003evinylpro.co.uk\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003ePW-Sat2 CubeSat secondary structure and panels\u003c\/td\u003e\n\u003ctd\u003eM2.5 x 4mm solar panel brackets, M2.5 x 6mm sun sensor mount, M2.5 x 8mm secondary structure to X frames\u003c\/td\u003e\n\u003ctd\u003epw-sat.pl\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eTEKTELIC Kona Photon Gen-2 LoRaWAN gateway\u003c\/td\u003e\n\u003ctd\u003eM2.5 x 8mm screws for the SIM tray access-port cover\u003c\/td\u003e\n\u003ctd\u003etektelic.com\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003ePhono cartridge headshell mounting screws (Tonar universal set)\u003c\/td\u003e\n\u003ctd\u003eProduct spec explicitly lists 'Screw type: M2.5 non-magnetic hardware' for mounting nearly any phono cartridge to headshell\u003c\/td\u003e\n\u003ctd\u003esoundium.com\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eOyaide SCR-S phono cartridge screw set\u003c\/td\u003e\n\u003ctd\u003eProduct titled 'Oyaide M2.5 phono cartridge screw set w\/carbon graphite nylon washer', contains 6\/8\/10mm lengths, explicit M2.5 thread\u003c\/td\u003e\n\u003ctd\u003eaudiohobby.eu\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eOpenFlexure Delta Stage v1.1.0 motor mounts\u003c\/td\u003e\n\u003ctd\u003e8x M2.5x8mm screws secure the stepper motors\u003c\/td\u003e\n\u003ctd\u003ebuild.openflexure.org\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eHP 250R G9 \/ 256R G9\u003c\/td\u003e\n\u003ctd\u003echassis feet screws (4x)\u003c\/td\u003e\n\u003ctd\u003ekaas.hpcloud.hp.com\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eAcer Aspire 5332 \/ 5732Z\u003c\/td\u003e\n\u003ctd\u003eScrew List: SCREW M2.45D 8.0L K 5.5D 0.8T ZKNL\u003c\/td\u003e\n\u003ctd\u003emanualowl.com\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003cp\u003eFull list: \u003ca href=\"https:\/\/screwfitmentdatabase.com\/m2-5x8mm\"\u003eM2.5 x 8mm on Screw Fitment Database\u003c\/a\u003e\u003c\/p\u003e\n\u003ch4\u003eWhat does an M2.5 x 8mm screw fit?\u003c\/h4\u003e\n\u003cp\u003eService manuals and manufacturer specs list an M2.5 x 8mm screw in: Eurorack module\/rail mounting screw; RC servo horn retaining screw (Hitec\/Futaba style); Turntable cartridge mounting kit (retail); PW-Sat2 CubeSat secondary structure and panels; TEKTELIC Kona Photon Gen-2 LoRaWAN gateway. Match the head style of the screw you removed (this is a flat countersunk Phillips head).\u003c\/p\u003e\n\u003cscript type=\"application\/ld+json\"\u003e{\"@context\": \"https:\/\/schema.org\", \"@type\": \"FAQPage\", \"mainEntity\": [{\"@type\": \"Question\", \"name\": \"What does an M2.5 x 8mm screw fit?\", \"acceptedAnswer\": {\"@type\": \"Answer\", \"text\": \"Service manuals and manufacturer specs list an M2.5 x 8mm screw in: Eurorack module\/rail mounting screw; RC servo horn retaining screw (Hitec\/Futaba style); Turntable cartridge mounting kit (retail); PW-Sat2 CubeSat secondary structure and panels; TEKTELIC Kona Photon Gen-2 LoRaWAN gateway. Match the head style of the screw you removed (this is a flat countersunk Phillips head).\"}}]}\u003c\/script\u003e\n\u003c\/div\u003e\u003c!-- tsw-fits:end --\u003e","brand":"TechSpareWarehouse","offers":[{"title":"Default Title","offer_id":43433435758666,"sku":"M2.5X8-PFH-CS-BLK-10PK-RPI","price":4.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0691\/7351\/0218\/files\/57_4335a15f-4d0c-4caf-a7f3-7232036f3ea0.jpg?v=1774301929"},{"product_id":"m2-5-x-8mm-screws-for-retevis-rt27-radio-belt-clip-10-pack-black-phillips","title":"M2.5 x 8mm Screws for Retevis RT27 Radio Belt Clip 10-Pack Black Phillips","description":"\u003ch2\u003eM2.5 x 8mm Replacement Screws for Retevis RT27 Radio Belt Clip | Black | 10-Pack\u003c\/h2\u003e\u003cp\u003eExact replacement M2.5 x 8mm screws for Retevis RT27 and compatible walkie-talkie belt clip mounting.\u003c\/p\u003e\u003ch3\u003eWhy the Right Screw Matters\u003c\/h3\u003e\u003cp\u003eRetevis RT27 belt clip screws are small and easily lost or stripped during clip removal. Without the correct screw the clip cannot be securely reattached making the radio impossible to carry hands-free.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003eStripped threads and damaged housings\u003c\/li\u003e\n\u003cli\u003eLoose components causing poor performance or failure\u003c\/li\u003e\n\u003cli\u003ePermanent damage to delicate assemblies\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eCompatibility\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eRetevis RT27 belt clip mounting\u003c\/li\u003e\n\u003cli\u003eRetevis H777 and compatible radio belt clips\u003c\/li\u003e\n\u003cli\u003eGeneral two-way radio belt clip hardware\u003c\/li\u003e\n\u003cli\u003eWalkie-talkie accessory repair and replacement\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eSpecifications\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eScrew Type:\u003c\/strong\u003e Machine Screw\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eThread Size:\u003c\/strong\u003e M2.5\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eLength:\u003c\/strong\u003e 8mm\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eHead Style:\u003c\/strong\u003e Phillips Flat Head (Low Profile)\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eDrive Style:\u003c\/strong\u003e Phillips\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eMaterial:\u003c\/strong\u003e Carbon Steel\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eFinish:\u003c\/strong\u003e Black Oxide\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eThread Standard:\u003c\/strong\u003e Metric\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003ePack Quantity:\u003c\/strong\u003e 10 Screws\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003e\u003cstrong\u003eImportant:\u003c\/strong\u003e M2.5 screws are not compatible with M2 or M3 threaded holes. Please verify your thread size before ordering.\u003c\/p\u003e\n\n\u003c!-- tsw-fits:start --\u003e\u003cdiv class=\"tsw-fits\"\u003e\n\u003ch3\u003eFits these models\u003c\/h3\u003e\n\u003cp\u003eDevices whose service manuals, parts lists or manufacturer specifications call for an \u003cb\u003eM2.5 x 8mm\u003c\/b\u003e metric screw at the position shown. The thread and length match; check that the screw you are replacing also has a flat (countersunk) head.\u003c\/p\u003e\n\u003ctable class=\"tsw-fits-table\"\u003e\n\u003cthead\u003e\u003ctr\u003e\n\u003cth\u003eDevice \/ model\u003c\/th\u003e\n\u003cth\u003eWhere the screw goes\u003c\/th\u003e\n\u003cth\u003eSource\u003c\/th\u003e\n\u003c\/tr\u003e\u003c\/thead\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003eRC servo horn retaining screw (Hitec\/Futaba style)\u003c\/td\u003e\n\u003ctd\u003eM2.5-0.45 x 8mm screw retains the servo horn\/arm\u003c\/td\u003e\n\u003ctd\u003eandymark.com\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eEurorack module\/rail mounting screw\u003c\/td\u003e\n\u003ctd\u003eSynthRacks sells M2.5 machine screws used to fix modules to Vector rails or Schroff rails with M2.5 nuts and threaded rails; 8mm length…\u003c\/td\u003e\n\u003ctd\u003esynthracks.com\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eTurntable cartridge mounting kit (retail)\u003c\/td\u003e\n\u003ctd\u003e'2 x M2.5x3 mm Stainless Steel Screws. 2 x M2.5x6 mm Stainless Steel Screws. 2 x M2.5x8 mm...' cartridge\/tonearm mounting fixings\u003c\/td\u003e\n\u003ctd\u003evinylpro.co.uk\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003ePW-Sat2 CubeSat secondary structure and panels\u003c\/td\u003e\n\u003ctd\u003eM2.5 x 4mm solar panel brackets, M2.5 x 6mm sun sensor mount, M2.5 x 8mm secondary structure to X frames\u003c\/td\u003e\n\u003ctd\u003epw-sat.pl\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eTEKTELIC Kona Photon Gen-2 LoRaWAN gateway\u003c\/td\u003e\n\u003ctd\u003eM2.5 x 8mm screws for the SIM tray access-port cover\u003c\/td\u003e\n\u003ctd\u003etektelic.com\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003ePhono cartridge headshell mounting screws (Tonar universal set)\u003c\/td\u003e\n\u003ctd\u003eProduct spec explicitly lists 'Screw type: M2.5 non-magnetic hardware' for mounting nearly any phono cartridge to headshell\u003c\/td\u003e\n\u003ctd\u003esoundium.com\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eOyaide SCR-S phono cartridge screw set\u003c\/td\u003e\n\u003ctd\u003eProduct titled 'Oyaide M2.5 phono cartridge screw set w\/carbon graphite nylon washer', contains 6\/8\/10mm lengths, explicit M2.5 thread\u003c\/td\u003e\n\u003ctd\u003eaudiohobby.eu\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eOpenFlexure Delta Stage v1.1.0 motor mounts\u003c\/td\u003e\n\u003ctd\u003e8x M2.5x8mm screws secure the stepper motors\u003c\/td\u003e\n\u003ctd\u003ebuild.openflexure.org\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eHP 250R G9 \/ 256R G9\u003c\/td\u003e\n\u003ctd\u003echassis feet screws (4x)\u003c\/td\u003e\n\u003ctd\u003ekaas.hpcloud.hp.com\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eAcer Aspire 5332 \/ 5732Z\u003c\/td\u003e\n\u003ctd\u003eScrew List: SCREW M2.45D 8.0L K 5.5D 0.8T ZKNL\u003c\/td\u003e\n\u003ctd\u003emanualowl.com\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003cp\u003eFull list: \u003ca href=\"https:\/\/screwfitmentdatabase.com\/m2-5x8mm\"\u003eM2.5 x 8mm on Screw Fitment Database\u003c\/a\u003e\u003c\/p\u003e\n\u003ch4\u003eWhat does an M2.5 x 8mm screw fit?\u003c\/h4\u003e\n\u003cp\u003eService manuals and manufacturer specs list an M2.5 x 8mm screw in: RC servo horn retaining screw (Hitec\/Futaba style); Eurorack module\/rail mounting screw; Turntable cartridge mounting kit (retail); PW-Sat2 CubeSat secondary structure and panels; TEKTELIC Kona Photon Gen-2 LoRaWAN gateway. Match the head style of the screw you removed (this is a flat countersunk Phillips head).\u003c\/p\u003e\n\u003cscript type=\"application\/ld+json\"\u003e{\"@context\": \"https:\/\/schema.org\", \"@type\": \"FAQPage\", \"mainEntity\": [{\"@type\": \"Question\", \"name\": \"What does an M2.5 x 8mm screw fit?\", \"acceptedAnswer\": {\"@type\": \"Answer\", \"text\": \"Service manuals and manufacturer specs list an M2.5 x 8mm screw in: RC servo horn retaining screw (Hitec\/Futaba style); Eurorack module\/rail mounting screw; Turntable cartridge mounting kit (retail); PW-Sat2 CubeSat secondary structure and panels; TEKTELIC Kona Photon Gen-2 LoRaWAN gateway. Match the head style of the screw you removed (this is a flat countersunk Phillips head).\"}}]}\u003c\/script\u003e\n\u003c\/div\u003e\u003c!-- tsw-fits:end --\u003e","brand":"TechSpareWarehouse","offers":[{"title":"Default Title","offer_id":43433435856970,"sku":"M2.5X8-PFH-CS-BLK-10PK-RTV","price":4.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0691\/7351\/0218\/files\/57_d586d50e-faab-41a3-9c0c-f349ec0c842b.jpg?v=1774301932"},{"product_id":"m25-x-8mm-phillips-flat-head-screw-for-laptop-bottom-cover-replacement-single-replacement-black","title":"M2.5 x 8mm Phillips Flat Head Screw for Laptop Bottom Cover Replacement - Single Replacement Black","description":"\u003ch2\u003eM2.5 x 8mm Phillips Flat Head Screw for Laptop Bottom Cover Replacement\u003c\/h2\u003e\u003cp\u003eLost a single screw during a repair? This listing is for one (1) M2.5 x 8mm Phillips flat head black oxide carbon steel screw, sized specifically for use in Laptop Bottom Cover Replacement. Sold individually so you only buy what you actually need.\u003c\/p\u003e\u003ch3\u003eWhy the Right Screw Matters\u003c\/h3\u003e\u003cp\u003eUsing the wrong screw size can cause permanent damage to your hardware. A screw that is too long can puncture components, crack motherboards, or push through chassis. A screw too short will not hold, and the wrong thread diameter will strip threads in their seats and ruin standoffs.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003eWrong length: punctured PCBs, cracked housings, broken battery cells\u003c\/li\u003e\n\u003cli\u003eWrong diameter: stripped threads in standoffs and inserts\u003c\/li\u003e\n\u003cli\u003eWrong drive type: cammed-out heads and unrecoverable fasteners\u003c\/li\u003e\n\u003cli\u003eWrong finish: corrosion and rust over time\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eWhat You Get\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eQuantity: 1 (one) screw - sold individually\u003c\/li\u003e\n\u003cli\u003eThread: M2.5 (metric coarse, 0.45mm pitch)\u003c\/li\u003e\n\u003cli\u003eLength: 8mm under the head\u003c\/li\u003e\n\u003cli\u003eHead style: Phillips flat head \u003c\/li\u003e\n\u003cli\u003eMaterial: carbon steel with black oxide finish\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eCompatibility\u003c\/h3\u003e\u003cp\u003eThis M2.5 x 8mm screw is commonly used in:\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003eLaptop Bottom Cover Replacement\u003c\/li\u003e\n\u003cli\u003eCompatible models: Universal Laptop Bottom Cover\u003c\/li\u003e\n\u003cli\u003eOther equipment using M2.5 x 8mm Phillips flat head fasteners\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eSpecifications\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eScrew size: M2.5 x 8mm\u003c\/li\u003e\n\u003cli\u003eThread diameter: 2.5mm\u003c\/li\u003e\n\u003cli\u003eThread pitch: 0.45mm (metric standard)\u003c\/li\u003e\n\u003cli\u003eLength: 8mm\u003c\/li\u003e\n\u003cli\u003eHead: flat \/  Phillips drive\u003c\/li\u003e\n\u003cli\u003eMaterial: carbon steel\u003c\/li\u003e\n\u003cli\u003eFinish: black oxide\u003c\/li\u003e\n\u003cli\u003eStandard: Metric\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003e\u003cstrong\u003eImportant:\u003c\/strong\u003e Do not mix metric M-sizes. M2 and M2.5 look similar but have different thread diameters and pitches - using the wrong one will cross-thread or strip the seat. Always verify the original screw's diameter and length before installing.\u003c\/p\u003e","brand":"TechSpareWarehouse","offers":[{"title":"Default Title","offer_id":43542360293450,"sku":"M2-5X8-PFH-CS-BLK-1PK-LPBOT-060","price":0.1,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0691\/7351\/0218\/files\/s-l1600_0de5a8fb-8836-4f5c-b42b-8637c7c1d5d6.webp?v=1777162958"},{"product_id":"m25-x-8mm-phillips-flat-head-screw-for-jfa-snackbox-micro-fight-stick-case-single-replacement-black","title":"M2.5 x 8mm Phillips Flat Head Screw for JFA Snackbox Micro Fight Stick Case - Single Replacement Black","description":"\u003ch2\u003eM2.5 x 8mm Phillips Flat Head Screw for JFA Snackbox Micro Fight Stick Case\u003c\/h2\u003e\u003cp\u003eLost a single screw during a repair? This listing is for one (1) M2.5 x 8mm Phillips flat head black oxide carbon steel screw, sized specifically for use in JFA Snackbox Micro Fight Stick Case. Sold individually so you only buy what you actually need.\u003c\/p\u003e\u003ch3\u003eWhy the Right Screw Matters\u003c\/h3\u003e\u003cp\u003eUsing the wrong screw size can cause permanent damage to your hardware. A screw that is too long can puncture components, crack motherboards, or push through chassis. A screw too short will not hold, and the wrong thread diameter will strip threads in their seats and ruin standoffs.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003eWrong length: punctured PCBs, cracked housings, broken battery cells\u003c\/li\u003e\n\u003cli\u003eWrong diameter: stripped threads in standoffs and inserts\u003c\/li\u003e\n\u003cli\u003eWrong drive type: cammed-out heads and unrecoverable fasteners\u003c\/li\u003e\n\u003cli\u003eWrong finish: corrosion and rust over time\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eWhat You Get\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eQuantity: 1 (one) screw - sold individually\u003c\/li\u003e\n\u003cli\u003eThread: M2.5 (metric coarse, 0.45mm pitch)\u003c\/li\u003e\n\u003cli\u003eLength: 8mm under the head\u003c\/li\u003e\n\u003cli\u003eHead style: Phillips flat head \u003c\/li\u003e\n\u003cli\u003eMaterial: carbon steel with black oxide finish\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eCompatibility\u003c\/h3\u003e\u003cp\u003eThis M2.5 x 8mm screw is commonly used in:\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003eJFA Snackbox Micro Fight Stick Case\u003c\/li\u003e\n\u003cli\u003eCompatible models: JFA Snackbox Micro\u003c\/li\u003e\n\u003cli\u003eOther equipment using M2.5 x 8mm Phillips flat head fasteners\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eSpecifications\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eScrew size: M2.5 x 8mm\u003c\/li\u003e\n\u003cli\u003eThread diameter: 2.5mm\u003c\/li\u003e\n\u003cli\u003eThread pitch: 0.45mm (metric standard)\u003c\/li\u003e\n\u003cli\u003eLength: 8mm\u003c\/li\u003e\n\u003cli\u003eHead: flat \/  Phillips drive\u003c\/li\u003e\n\u003cli\u003eMaterial: carbon steel\u003c\/li\u003e\n\u003cli\u003eFinish: black oxide\u003c\/li\u003e\n\u003cli\u003eStandard: Metric\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003e\u003cstrong\u003eImportant:\u003c\/strong\u003e Do not mix metric M-sizes. M2 and M2.5 look similar but have different thread diameters and pitches - using the wrong one will cross-thread or strip the seat. Always verify the original screw's diameter and length before installing.\u003c\/p\u003e","brand":"TechSpareWarehouse","offers":[{"title":"Default Title","offer_id":43542360522826,"sku":"M2-5X8-PFH-CS-BLK-1PK-JFASB-066","price":0.1,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0691\/7351\/0218\/files\/s-l1600_3ae7e436-6000-4714-bfb6-9b3a95cd15ce.webp?v=1777162964"},{"product_id":"m25-x-8mm-phillips-flat-head-screw-for-lenovo-legion-5-gaming-laptop-repair-single-replacement-black","title":"M2.5 x 8mm Phillips Flat Head Screw for Lenovo Legion 5 Gaming Laptop Repair - Single Replacement Black","description":"\u003ch2\u003eM2.5 x 8mm Phillips Flat Head Screw for Lenovo Legion 5 Gaming Laptop Repair\u003c\/h2\u003e\u003cp\u003eLost a single screw during a repair? This listing is for one (1) M2.5 x 8mm Phillips flat head black oxide carbon steel screw, sized specifically for use in Lenovo Legion 5 Gaming Laptop Repair. Sold individually so you only buy what you actually need.\u003c\/p\u003e\u003ch3\u003eWhy the Right Screw Matters\u003c\/h3\u003e\u003cp\u003eUsing the wrong screw size can cause permanent damage to your hardware. A screw that is too long can puncture components, crack motherboards, or push through chassis. A screw too short will not hold, and the wrong thread diameter will strip threads in their seats and ruin standoffs.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003eWrong length: punctured PCBs, cracked housings, broken battery cells\u003c\/li\u003e\n\u003cli\u003eWrong diameter: stripped threads in standoffs and inserts\u003c\/li\u003e\n\u003cli\u003eWrong drive type: cammed-out heads and unrecoverable fasteners\u003c\/li\u003e\n\u003cli\u003eWrong finish: corrosion and rust over time\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eWhat You Get\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eQuantity: 1 (one) screw - sold individually\u003c\/li\u003e\n\u003cli\u003eThread: M2.5 (metric coarse, 0.45mm pitch)\u003c\/li\u003e\n\u003cli\u003eLength: 8mm under the head\u003c\/li\u003e\n\u003cli\u003eHead style: Phillips flat head \u003c\/li\u003e\n\u003cli\u003eMaterial: carbon steel with black oxide finish\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eCompatibility\u003c\/h3\u003e\u003cp\u003eThis M2.5 x 8mm screw is commonly used in:\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003eLenovo Legion 5 Gaming Laptop Repair\u003c\/li\u003e\n\u003cli\u003eCompatible models: Lenovo Legion 5\u003c\/li\u003e\n\u003cli\u003eOther equipment using M2.5 x 8mm Phillips flat head fasteners\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eSpecifications\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eScrew size: M2.5 x 8mm\u003c\/li\u003e\n\u003cli\u003eThread diameter: 2.5mm\u003c\/li\u003e\n\u003cli\u003eThread pitch: 0.45mm (metric standard)\u003c\/li\u003e\n\u003cli\u003eLength: 8mm\u003c\/li\u003e\n\u003cli\u003eHead: flat \/  Phillips drive\u003c\/li\u003e\n\u003cli\u003eMaterial: carbon steel\u003c\/li\u003e\n\u003cli\u003eFinish: black oxide\u003c\/li\u003e\n\u003cli\u003eStandard: Metric\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003e\u003cstrong\u003eImportant:\u003c\/strong\u003e Do not mix metric M-sizes. M2 and M2.5 look similar but have different thread diameters and pitches - using the wrong one will cross-thread or strip the seat. Always verify the original screw's diameter and length before installing.\u003c\/p\u003e\u003c!-- tsw-fits:start --\u003e\u003cdiv class=\"tsw-fits\"\u003e\n\u003ch3\u003eFits these models\u003c\/h3\u003e\n\u003cp\u003eDevices whose service manuals, parts lists or manufacturer specifications call for an \u003cb\u003eM2.5 x 8mm\u003c\/b\u003e metric screw at the position shown. The thread and length match; check that the screw you are replacing also has a flat (countersunk) head.\u003c\/p\u003e\n\u003ctable class=\"tsw-fits-table\"\u003e\n\u003cthead\u003e\u003ctr\u003e\n\u003cth\u003eDevice \/ model\u003c\/th\u003e\n\u003cth\u003eWhere the screw goes\u003c\/th\u003e\n\u003cth\u003eSource\u003c\/th\u003e\n\u003c\/tr\u003e\u003c\/thead\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003eRC servo horn retaining screw (Hitec\/Futaba style)\u003c\/td\u003e\n\u003ctd\u003eM2.5-0.45 x 8mm screw retains the servo horn\/arm\u003c\/td\u003e\n\u003ctd\u003eandymark.com\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eEurorack module\/rail mounting screw\u003c\/td\u003e\n\u003ctd\u003eSynthRacks sells M2.5 machine screws used to fix modules to Vector rails or Schroff rails with M2.5 nuts and threaded rails; 8mm length…\u003c\/td\u003e\n\u003ctd\u003esynthracks.com\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eTurntable cartridge mounting kit (retail)\u003c\/td\u003e\n\u003ctd\u003e'2 x M2.5x3 mm Stainless Steel Screws. 2 x M2.5x6 mm Stainless Steel Screws. 2 x M2.5x8 mm...' cartridge\/tonearm mounting fixings\u003c\/td\u003e\n\u003ctd\u003evinylpro.co.uk\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003ePW-Sat2 CubeSat secondary structure and panels\u003c\/td\u003e\n\u003ctd\u003eM2.5 x 4mm solar panel brackets, M2.5 x 6mm sun sensor mount, M2.5 x 8mm secondary structure to X frames\u003c\/td\u003e\n\u003ctd\u003epw-sat.pl\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eTEKTELIC Kona Photon Gen-2 LoRaWAN gateway\u003c\/td\u003e\n\u003ctd\u003eM2.5 x 8mm screws for the SIM tray access-port cover\u003c\/td\u003e\n\u003ctd\u003etektelic.com\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003ePhono cartridge headshell mounting screws (Tonar universal set)\u003c\/td\u003e\n\u003ctd\u003eProduct spec explicitly lists 'Screw type: M2.5 non-magnetic hardware' for mounting nearly any phono cartridge to headshell\u003c\/td\u003e\n\u003ctd\u003esoundium.com\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eOyaide SCR-S phono cartridge screw set\u003c\/td\u003e\n\u003ctd\u003eProduct titled 'Oyaide M2.5 phono cartridge screw set w\/carbon graphite nylon washer', contains 6\/8\/10mm lengths, explicit M2.5 thread\u003c\/td\u003e\n\u003ctd\u003eaudiohobby.eu\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eOpenFlexure Delta Stage v1.1.0 motor mounts\u003c\/td\u003e\n\u003ctd\u003e8x M2.5x8mm screws secure the stepper motors\u003c\/td\u003e\n\u003ctd\u003ebuild.openflexure.org\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eHP 250R G9 \/ 256R G9\u003c\/td\u003e\n\u003ctd\u003echassis feet screws (4x)\u003c\/td\u003e\n\u003ctd\u003ekaas.hpcloud.hp.com\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eAcer Aspire 5332 \/ 5732Z\u003c\/td\u003e\n\u003ctd\u003eScrew List: SCREW M2.45D 8.0L K 5.5D 0.8T ZKNL\u003c\/td\u003e\n\u003ctd\u003emanualowl.com\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003cp\u003eFull list: \u003ca href=\"https:\/\/screwfitmentdatabase.com\/m2-5x8mm\"\u003eM2.5 x 8mm on Screw Fitment Database\u003c\/a\u003e\u003c\/p\u003e\n\u003ch4\u003eWhat does an M2.5 x 8mm screw fit?\u003c\/h4\u003e\n\u003cp\u003eService manuals and manufacturer specs list an M2.5 x 8mm screw in: RC servo horn retaining screw (Hitec\/Futaba style); Eurorack module\/rail mounting screw; Turntable cartridge mounting kit (retail); PW-Sat2 CubeSat secondary structure and panels; TEKTELIC Kona Photon Gen-2 LoRaWAN gateway. Match the head style of the screw you removed (this is a flat countersunk Phillips head).\u003c\/p\u003e\n\u003cscript type=\"application\/ld+json\"\u003e{\"@context\": \"https:\/\/schema.org\", \"@type\": \"FAQPage\", \"mainEntity\": [{\"@type\": \"Question\", \"name\": \"What does an M2.5 x 8mm screw fit?\", \"acceptedAnswer\": {\"@type\": \"Answer\", \"text\": \"Service manuals and manufacturer specs list an M2.5 x 8mm screw in: RC servo horn retaining screw (Hitec\/Futaba style); Eurorack module\/rail mounting screw; Turntable cartridge mounting kit (retail); PW-Sat2 CubeSat secondary structure and panels; TEKTELIC Kona Photon Gen-2 LoRaWAN gateway. Match the head style of the screw you removed (this is a flat countersunk Phillips head).\"}}]}\u003c\/script\u003e\n\u003c\/div\u003e\u003c!-- tsw-fits:end --\u003e","brand":"TechSpareWarehouse","offers":[{"title":"Default Title","offer_id":43542361178186,"sku":"M2-5X8-PFH-CS-BLK-1PK-LELEG5-088","price":0.1,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0691\/7351\/0218\/files\/s-l1600_a4a3cb10-5344-409d-a6c7-c7532fe9d1b4.webp?v=1777162983"},{"product_id":"m25-x-8mm-phillips-flat-head-screw-for-msi-gf63-katana-gaming-laptop-repair-single-replacement-black","title":"M2.5 x 8mm Phillips Flat Head Screw for MSI GF63 Katana Gaming Laptop Repair - Single Replacement Black","description":"\u003ch2\u003eM2.5 x 8mm Phillips Flat Head Screw for MSI GF63 Katana Gaming Laptop Repair\u003c\/h2\u003e\u003cp\u003eLost a single screw during a repair? This listing is for one (1) M2.5 x 8mm Phillips flat head black oxide carbon steel screw, sized specifically for use in MSI GF63 Katana Gaming Laptop Repair. Sold individually so you only buy what you actually need.\u003c\/p\u003e\u003ch3\u003eWhy the Right Screw Matters\u003c\/h3\u003e\u003cp\u003eUsing the wrong screw size can cause permanent damage to your hardware. A screw that is too long can puncture components, crack motherboards, or push through chassis. A screw too short will not hold, and the wrong thread diameter will strip threads in their seats and ruin standoffs.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003eWrong length: punctured PCBs, cracked housings, broken battery cells\u003c\/li\u003e\n\u003cli\u003eWrong diameter: stripped threads in standoffs and inserts\u003c\/li\u003e\n\u003cli\u003eWrong drive type: cammed-out heads and unrecoverable fasteners\u003c\/li\u003e\n\u003cli\u003eWrong finish: corrosion and rust over time\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eWhat You Get\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eQuantity: 1 (one) screw - sold individually\u003c\/li\u003e\n\u003cli\u003eThread: M2.5 (metric coarse, 0.45mm pitch)\u003c\/li\u003e\n\u003cli\u003eLength: 8mm under the head\u003c\/li\u003e\n\u003cli\u003eHead style: Phillips flat head \u003c\/li\u003e\n\u003cli\u003eMaterial: carbon steel with black oxide finish\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eCompatibility\u003c\/h3\u003e\u003cp\u003eThis M2.5 x 8mm screw is commonly used in:\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003eMSI GF63 Katana Gaming Laptop Repair\u003c\/li\u003e\n\u003cli\u003eCompatible models: MSI GF63, MSI Katana GF66\u003c\/li\u003e\n\u003cli\u003eOther equipment using M2.5 x 8mm Phillips flat head fasteners\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eSpecifications\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eScrew size: M2.5 x 8mm\u003c\/li\u003e\n\u003cli\u003eThread diameter: 2.5mm\u003c\/li\u003e\n\u003cli\u003eThread pitch: 0.45mm (metric standard)\u003c\/li\u003e\n\u003cli\u003eLength: 8mm\u003c\/li\u003e\n\u003cli\u003eHead: flat \/  Phillips drive\u003c\/li\u003e\n\u003cli\u003eMaterial: carbon steel\u003c\/li\u003e\n\u003cli\u003eFinish: black oxide\u003c\/li\u003e\n\u003cli\u003eStandard: Metric\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003e\u003cstrong\u003eImportant:\u003c\/strong\u003e Do not mix metric M-sizes. M2 and M2.5 look similar but have different thread diameters and pitches - using the wrong one will cross-thread or strip the seat. Always verify the original screw's diameter and length before installing.\u003c\/p\u003e\u003c!-- tsw-fits:start --\u003e\u003cdiv class=\"tsw-fits\"\u003e\n\u003ch3\u003eFits these models\u003c\/h3\u003e\n\u003cp\u003eDevices whose service manuals, parts lists or manufacturer specifications call for an \u003cb\u003eM2.5 x 8mm\u003c\/b\u003e metric screw at the position shown. The thread and length match; check that the screw you are replacing also has a flat (countersunk) head.\u003c\/p\u003e\n\u003ctable class=\"tsw-fits-table\"\u003e\n\u003cthead\u003e\u003ctr\u003e\n\u003cth\u003eDevice \/ model\u003c\/th\u003e\n\u003cth\u003eWhere the screw goes\u003c\/th\u003e\n\u003cth\u003eSource\u003c\/th\u003e\n\u003c\/tr\u003e\u003c\/thead\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003eRC servo horn retaining screw (Hitec\/Futaba style)\u003c\/td\u003e\n\u003ctd\u003eM2.5-0.45 x 8mm screw retains the servo horn\/arm\u003c\/td\u003e\n\u003ctd\u003eandymark.com\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eEurorack module\/rail mounting screw\u003c\/td\u003e\n\u003ctd\u003eSynthRacks sells M2.5 machine screws used to fix modules to Vector rails or Schroff rails with M2.5 nuts and threaded rails; 8mm length…\u003c\/td\u003e\n\u003ctd\u003esynthracks.com\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eTurntable cartridge mounting kit (retail)\u003c\/td\u003e\n\u003ctd\u003e'2 x M2.5x3 mm Stainless Steel Screws. 2 x M2.5x6 mm Stainless Steel Screws. 2 x M2.5x8 mm...' cartridge\/tonearm mounting fixings\u003c\/td\u003e\n\u003ctd\u003evinylpro.co.uk\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003ePW-Sat2 CubeSat secondary structure and panels\u003c\/td\u003e\n\u003ctd\u003eM2.5 x 4mm solar panel brackets, M2.5 x 6mm sun sensor mount, M2.5 x 8mm secondary structure to X frames\u003c\/td\u003e\n\u003ctd\u003epw-sat.pl\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eTEKTELIC Kona Photon Gen-2 LoRaWAN gateway\u003c\/td\u003e\n\u003ctd\u003eM2.5 x 8mm screws for the SIM tray access-port cover\u003c\/td\u003e\n\u003ctd\u003etektelic.com\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003ePhono cartridge headshell mounting screws (Tonar universal set)\u003c\/td\u003e\n\u003ctd\u003eProduct spec explicitly lists 'Screw type: M2.5 non-magnetic hardware' for mounting nearly any phono cartridge to headshell\u003c\/td\u003e\n\u003ctd\u003esoundium.com\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eOyaide SCR-S phono cartridge screw set\u003c\/td\u003e\n\u003ctd\u003eProduct titled 'Oyaide M2.5 phono cartridge screw set w\/carbon graphite nylon washer', contains 6\/8\/10mm lengths, explicit M2.5 thread\u003c\/td\u003e\n\u003ctd\u003eaudiohobby.eu\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eOpenFlexure Delta Stage v1.1.0 motor mounts\u003c\/td\u003e\n\u003ctd\u003e8x M2.5x8mm screws secure the stepper motors\u003c\/td\u003e\n\u003ctd\u003ebuild.openflexure.org\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eHP 250R G9 \/ 256R G9\u003c\/td\u003e\n\u003ctd\u003echassis feet screws (4x)\u003c\/td\u003e\n\u003ctd\u003ekaas.hpcloud.hp.com\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eAcer Aspire 5332 \/ 5732Z\u003c\/td\u003e\n\u003ctd\u003eScrew List: SCREW M2.45D 8.0L K 5.5D 0.8T ZKNL\u003c\/td\u003e\n\u003ctd\u003emanualowl.com\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003cp\u003eFull list: \u003ca href=\"https:\/\/screwfitmentdatabase.com\/m2-5x8mm\"\u003eM2.5 x 8mm on Screw Fitment Database\u003c\/a\u003e\u003c\/p\u003e\n\u003ch4\u003eWhat does an M2.5 x 8mm screw fit?\u003c\/h4\u003e\n\u003cp\u003eService manuals and manufacturer specs list an M2.5 x 8mm screw in: RC servo horn retaining screw (Hitec\/Futaba style); Eurorack module\/rail mounting screw; Turntable cartridge mounting kit (retail); PW-Sat2 CubeSat secondary structure and panels; TEKTELIC Kona Photon Gen-2 LoRaWAN gateway. Match the head style of the screw you removed (this is a flat countersunk Phillips head).\u003c\/p\u003e\n\u003cscript type=\"application\/ld+json\"\u003e{\"@context\": \"https:\/\/schema.org\", \"@type\": \"FAQPage\", \"mainEntity\": [{\"@type\": \"Question\", \"name\": \"What does an M2.5 x 8mm screw fit?\", \"acceptedAnswer\": {\"@type\": \"Answer\", \"text\": \"Service manuals and manufacturer specs list an M2.5 x 8mm screw in: RC servo horn retaining screw (Hitec\/Futaba style); Eurorack module\/rail mounting screw; Turntable cartridge mounting kit (retail); PW-Sat2 CubeSat secondary structure and panels; TEKTELIC Kona Photon Gen-2 LoRaWAN gateway. Match the head style of the screw you removed (this is a flat countersunk Phillips head).\"}}]}\u003c\/script\u003e\n\u003c\/div\u003e\u003c!-- tsw-fits:end --\u003e","brand":"TechSpareWarehouse","offers":[{"title":"Default Title","offer_id":43542362259530,"sku":"M2-5X8-PFH-CS-BLK-1PK-MSIGF63-115","price":0.1,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0691\/7351\/0218\/files\/s-l1600_eba370e3-04fc-404b-bb29-66f41f415daa.webp?v=1777163013"},{"product_id":"m25-x-8mm-phillips-flat-head-screw-for-turntable-cartridge-headshell-mount-pack-of-50-black","title":"M2.5 x 8mm Phillips Flat Head Screw for Turntable Cartridge Headshell Mount - Pack of 50 Black","description":"\u003ch2\u003eM2.5 x 8mm Phillips Flat Head Screw for Turntable Cartridge Headshell Mount - Pack of 50\u003c\/h2\u003e\u003cp\u003eNeed screws for ongoing repairs? This listing is for a pack of fifty (50) M2.5 x 8mm Phillips flat head black oxide carbon steel screw, sized specifically for use in Turntable Cartridge Headshell Mount. Sold in a pack of 50 — ideal for ongoing repairs, service shops, and keeping your toolkit stocked.\u003c\/p\u003e\u003ch3\u003eWhy the Right Screw Matters\u003c\/h3\u003e\u003cp\u003eUsing the wrong screw size can cause permanent damage to your hardware. A screw that is too long can puncture components, crack motherboards, or push through chassis. A screw too short will not hold, and the wrong thread diameter will strip threads in their seats and ruin standoffs.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003eWrong length: punctured PCBs, cracked housings, broken battery cells\u003c\/li\u003e\n\u003cli\u003eWrong diameter: stripped threads in standoffs and inserts\u003c\/li\u003e\n\u003cli\u003eWrong drive type: cammed-out heads and unrecoverable fasteners\u003c\/li\u003e\n\u003cli\u003eWrong finish: corrosion and rust over time\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eWhat You Get\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eQuantity: 50 screws per pack\u003c\/li\u003e\n\u003cli\u003eThread: M2.5 (metric coarse, 0.45mm pitch)\u003c\/li\u003e\n\u003cli\u003eLength: 8mm under the head\u003c\/li\u003e\n\u003cli\u003eHead style: Phillips flat head \u003c\/li\u003e\n\u003cli\u003eMaterial: carbon steel with black oxide finish\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eCompatibility\u003c\/h3\u003e\u003cp\u003eThis M2.5 x 8mm screw is commonly used in:\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003eTurntable Cartridge Headshell Mount\u003c\/li\u003e\n\u003cli\u003eCompatible models: Audio-Technica, Ortofon, Shure Headshells\u003c\/li\u003e\n\u003cli\u003eOther equipment using M2.5 x 8mm Phillips flat head fasteners\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eSpecifications\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eScrew size: M2.5 x 8mm\u003c\/li\u003e\n\u003cli\u003eThread diameter: 2.5mm\u003c\/li\u003e\n\u003cli\u003eThread pitch: 0.45mm (metric standard)\u003c\/li\u003e\n\u003cli\u003eLength: 8mm\u003c\/li\u003e\n\u003cli\u003eHead: flat \/  Phillips drive\u003c\/li\u003e\n\u003cli\u003eMaterial: carbon steel\u003c\/li\u003e\n\u003cli\u003eFinish: black oxide\u003c\/li\u003e\n\u003cli\u003eStandard: Metric\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003e\u003cstrong\u003eImportant:\u003c\/strong\u003e Do not mix metric M-sizes. M2 and M2.5 look similar but have different thread diameters and pitches - using the wrong one will cross-thread or strip the seat. Always verify the original screw's diameter and length before installing.\u003c\/p\u003e","brand":"TechSpareWarehouse","offers":[{"title":"Default Title","offer_id":43692192530506,"sku":"M2-5X8-PFH-CS-BLK-50PK-TTHEAD-076","price":5.49,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0691\/7351\/0218\/files\/s-l1600_61b22874-a1d3-4632-ab2f-ee64b42450c4.webp?v=1777162972"},{"product_id":"25x-m2-5-x-8mm-phillips-screws-for-acer-nitro-5-lcd-hinge-assembly","title":"25x M2.5 x 8mm Phillips Screws for Acer Nitro 5 LCD Hinge Assembly","description":"\u003cp\u003eReplacement \u003cstrong\u003eM2.5 x 8mm\u003c\/strong\u003e Phillips screws for the \u003cstrong\u003eAcer Nitro 5\u003c\/strong\u003e LCD hinge assembly. Sold as a 25-pack so you have spares for future repairs.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eSize:\u003c\/strong\u003e M2.5 thread × 8mm length\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eDrive:\u003c\/strong\u003e Phillips\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eHead:\u003c\/strong\u003e Low-profile flat head — sits flush\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eFinish:\u003c\/strong\u003e Black carbon steel\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eQuantity:\u003c\/strong\u003e 25 screws\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eCheck the size before you order\u003c\/h3\u003e\u003cp\u003eM2.5 x 8mm means a 2.5mm metric thread, 8mm long. Laptops use several lengths of the same thread in different places, so match the location, not just the model. If you still have an original screw from the same spot, compare it, or measure the thread and length with calipers.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003eA screw that is too long can press on the board, cable or battery underneath.\u003c\/li\u003e\n\u003cli\u003eA different thread size (for example M2 vs M2.5) will not hold and can strip the threaded insert.\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003eMore help: \u003ca href=\"\/pages\/screw-size-guide\"\u003eHow to measure a laptop screw\u003c\/a\u003e · \u003ca href=\"\/pages\/laptop-screws-by-model\"\u003eLaptop screws by model\u003c\/a\u003e · \u003ca href=\"\/pages\/acer-nitro-5-screws\"\u003eAcer Nitro 5 screw guide\u003c\/a\u003e.\u003c\/p\u003e","brand":"TechSpareWarehouse","offers":[{"title":"Default Title","offer_id":44193912782922,"sku":"TSW-ACRN5-M25X8-25PK","price":5.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0691\/7351\/0218\/files\/57_86335f47-a2a1-4dc0-8b23-8fce376a6eba.jpg?v=1774301917"},{"product_id":"m2-5-x-8mm-screws-for-lenovo-thinkpad-p15-gen-2-thinkpad-p17-gen-2-thinkpad-t15g-gen-2-display-replacement-10-pack-black","title":"M2.5 x 8mm Screws for Lenovo ThinkPad P15 Gen 2 \/ ThinkPad P17 Gen 2 \/ ThinkPad T15g Gen 2 Display Replacement – 10-Pack Black","description":"\u003ch2\u003eM2.5 x 8mm Screws for Lenovo ThinkPad P15 Gen 2 \/ ThinkPad P17 Gen 2 \/ ThinkPad T15g Gen 2 Display Replacement – 10-Pack Black\u003c\/h2\u003e\u003cp\u003e10 replacement M2.5 x 8mm black low-profile Phillips flat head screws for the Lenovo ThinkPad P15 Gen 2, ThinkPad P17 Gen 2, ThinkPad T15g Gen 2 display. Lenovo's Hardware Maintenance Manual lists M2.5 x 8mm screws for the display step shown below.\u003c\/p\u003e\u003ch3\u003eFits these models\u003c\/h3\u003e\u003ctable\u003e\n\u003ctr\u003e\n\u003cth\u003eDevice\u003c\/th\u003e\n\u003cth\u003eWhere it goes\u003c\/th\u003e\n\u003cth\u003eQty per unit\u003c\/th\u003e\n\u003cth\u003eSource\u003c\/th\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eLenovo ThinkPad P15 Gen 2\u003c\/td\u003e\n\u003ctd\u003eLCD unit\u003c\/td\u003e\n\u003ctd\u003e4\u003c\/td\u003e\n\u003ctd\u003e\u003ca href=\"https:\/\/download.lenovo.com\/pccbbs\/mobiles_pdf\/p15_gen2_t15g_gen2_p17_gen2_hmm_en.pdf\"\u003eLenovo P15 Gen 2, T15g Gen 2, and P17 Gen 2 service documentation (download.lenovo.com, p. 108)\u003c\/a\u003e\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eLenovo ThinkPad P17 Gen 2\u003c\/td\u003e\n\u003ctd\u003eLCD unit\u003c\/td\u003e\n\u003ctd\u003e4\u003c\/td\u003e\n\u003ctd\u003e\u003ca href=\"https:\/\/download.lenovo.com\/pccbbs\/mobiles_pdf\/p15_gen2_t15g_gen2_p17_gen2_hmm_en.pdf\"\u003eLenovo P15 Gen 2, T15g Gen 2, and P17 Gen 2 service documentation (download.lenovo.com, p. 108)\u003c\/a\u003e\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eLenovo ThinkPad T15g Gen 2\u003c\/td\u003e\n\u003ctd\u003eLCD unit\u003c\/td\u003e\n\u003ctd\u003e4\u003c\/td\u003e\n\u003ctd\u003e\u003ca href=\"https:\/\/download.lenovo.com\/pccbbs\/mobiles_pdf\/p15_gen2_t15g_gen2_p17_gen2_hmm_en.pdf\"\u003eLenovo P15 Gen 2, T15g Gen 2, and P17 Gen 2 service documentation (download.lenovo.com, p. 108)\u003c\/a\u003e\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/table\u003e\u003ch3\u003eCheck Before Ordering\u003c\/h3\u003e\u003cp\u003eThread M2.5 x 0.45 mm, 8 mm long, head about 5 mm.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003eOurs is a black low-profile Phillips flat head, about 5 mm across (see the photo). Lenovo's document calls this a flat-head screw. Compare the head with your original before ordering.\u003c\/li\u003e\n\u003cli\u003eThe original screws have a nylon thread-lock patch; these do not. Add a drop of low-strength threadlocker if needed.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eWhy the Right Screw Matters\u003c\/h3\u003e\u003cp\u003eThread, length and head all have to match. A screw that is too long can push into the parts behind it (a battery, a board or the keyboard); one that is too short or has the wrong head will not hold. 10 screws cover the position with spares.\u003c\/p\u003e\u003ch3\u003eWhat You Get\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e10 x M2.5 x 8mm black low-profile Phillips flat head machine screws\u003c\/li\u003e\n\u003cli\u003eBrand new, bagged and labelled\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eSpecifications\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eThread Size:\u003c\/strong\u003e M2.5 x 0.45mm (metric coarse)\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eLength:\u003c\/strong\u003e 8mm\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eHead Style:\u003c\/strong\u003e Phillips flat head, low profile\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eHead Diameter:\u003c\/strong\u003e about 5mm\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eDrive:\u003c\/strong\u003e Phillips\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eMaterial:\u003c\/strong\u003e Carbon steel\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eFinish:\u003c\/strong\u003e Black oxide\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003ePack:\u003c\/strong\u003e 10 pieces\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003e\u003cstrong\u003eImportant:\u003c\/strong\u003e compatible-size replacement screws, not genuine Lenovo parts. Brand and model names are used only to describe fit. Please verify the size against your laptop's service manual or the original screw before ordering.\u003c\/p\u003e","brand":"TechSpareWarehouse","offers":[{"title":"10-Pack","offer_id":67746136948810,"sku":"M25X8-PFH-CS-BLK-10PK-LETPP15G2-LCD","price":4.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0691\/7351\/0218\/files\/s-l1600_ddb21469-cfe1-44d3-8e03-d249696f0130.webp?v=1792459699"},{"product_id":"m2-5-x-8mm-screws-for-lenovo-thinkpad-p15-gen-1-thinkpad-t15g-gen-1-display-replacement-10-pack-black","title":"M2.5 x 8mm Screws for Lenovo ThinkPad P15 Gen 1 \/ ThinkPad T15g Gen 1 Display Replacement – 10-Pack Black","description":"\u003ch2\u003eM2.5 x 8mm Screws for Lenovo ThinkPad P15 Gen 1 \/ ThinkPad T15g Gen 1 Display Replacement – 10-Pack Black\u003c\/h2\u003e\u003cp\u003e10 replacement M2.5 x 8mm black low-profile Phillips flat head screws for the Lenovo ThinkPad P15 Gen 1, ThinkPad T15g Gen 1 display. Lenovo's Hardware Maintenance Manual lists M2.5 x 8mm screws for the display step shown below.\u003c\/p\u003e\u003ch3\u003eFits these models\u003c\/h3\u003e\u003ctable\u003e\n\u003ctr\u003e\n\u003cth\u003eDevice\u003c\/th\u003e\n\u003cth\u003eWhere it goes\u003c\/th\u003e\n\u003cth\u003eQty per unit\u003c\/th\u003e\n\u003cth\u003eSource\u003c\/th\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eLenovo ThinkPad P15 Gen 1\u003c\/td\u003e\n\u003ctd\u003eLCD unit\u003c\/td\u003e\n\u003ctd\u003e4\u003c\/td\u003e\n\u003ctd\u003e\u003ca href=\"https:\/\/download.lenovo.com\/pccbbs\/mobiles_pdf\/p15_t15g_gen1_hmm_en.pdf\"\u003eLenovo ThinkPad P15 Gen 1\/T15g Gen 1 service documentation (download.lenovo.com, p. 90)\u003c\/a\u003e\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eLenovo ThinkPad T15g Gen 1\u003c\/td\u003e\n\u003ctd\u003eLCD unit\u003c\/td\u003e\n\u003ctd\u003e4\u003c\/td\u003e\n\u003ctd\u003e\u003ca href=\"https:\/\/download.lenovo.com\/pccbbs\/mobiles_pdf\/p15_t15g_gen1_hmm_en.pdf\"\u003eLenovo ThinkPad P15 Gen 1\/T15g Gen 1 service documentation (download.lenovo.com, p. 90)\u003c\/a\u003e\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/table\u003e\u003ch3\u003eCheck Before Ordering\u003c\/h3\u003e\u003cp\u003eThread M2.5 x 0.45 mm, 8 mm long, head about 5 mm.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003eOurs is a black low-profile Phillips flat head, about 5 mm across (see the photo). Lenovo's document calls this a flat-head screw. Compare the head with your original before ordering.\u003c\/li\u003e\n\u003cli\u003eThe original screws have a nylon thread-lock patch; these do not. Add a drop of low-strength threadlocker if needed.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eWhy the Right Screw Matters\u003c\/h3\u003e\u003cp\u003eThread, length and head all have to match. A screw that is too long can push into the parts behind it (a battery, a board or the keyboard); one that is too short or has the wrong head will not hold. 10 screws cover the position with spares.\u003c\/p\u003e\u003ch3\u003eWhat You Get\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e10 x M2.5 x 8mm black low-profile Phillips flat head machine screws\u003c\/li\u003e\n\u003cli\u003eBrand new, bagged and labelled\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eSpecifications\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eThread Size:\u003c\/strong\u003e M2.5 x 0.45mm (metric coarse)\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eLength:\u003c\/strong\u003e 8mm\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eHead Style:\u003c\/strong\u003e Phillips flat head, low profile\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eHead Diameter:\u003c\/strong\u003e about 5mm\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eDrive:\u003c\/strong\u003e Phillips\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eMaterial:\u003c\/strong\u003e Carbon steel\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eFinish:\u003c\/strong\u003e Black oxide\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003ePack:\u003c\/strong\u003e 10 pieces\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003e\u003cstrong\u003eImportant:\u003c\/strong\u003e compatible-size replacement screws, not genuine Lenovo parts. Brand and model names are used only to describe fit. Please verify the size against your laptop's service manual or the original screw before ordering.\u003c\/p\u003e","brand":"TechSpareWarehouse","offers":[{"title":"10-Pack","offer_id":67746160705610,"sku":"M25X8-PFH-CS-BLK-10PK-LETPP15G1-LCD","price":4.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0691\/7351\/0218\/files\/s-l1600_e023ae8e-68de-4f7d-bb6a-667286168f71.webp?v=1792459778"},{"product_id":"m2-5-x-8mm-screws-for-lenovo-thinkpad-p53-display-replacement-10-pack-black","title":"M2.5 x 8mm Screws for Lenovo ThinkPad P53 Display Replacement – 10-Pack Black","description":"\u003ch2\u003eM2.5 x 8mm Screws for Lenovo ThinkPad P53 Display Replacement – 10-Pack Black\u003c\/h2\u003e\u003cp\u003e10 replacement M2.5 x 8mm black low-profile Phillips flat head screws for the Lenovo ThinkPad P53 display. Lenovo's Hardware Maintenance Manual lists M2.5 x 8mm screws for the display step shown below.\u003c\/p\u003e\u003ch3\u003eFits these models\u003c\/h3\u003e\u003ctable\u003e\n\u003ctr\u003e\n\u003cth\u003eDevice\u003c\/th\u003e\n\u003cth\u003eWhere it goes\u003c\/th\u003e\n\u003cth\u003eQty per unit\u003c\/th\u003e\n\u003cth\u003eSource\u003c\/th\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eLenovo ThinkPad P53\u003c\/td\u003e\n\u003ctd\u003eLCD unit\u003c\/td\u003e\n\u003ctd\u003e4\u003c\/td\u003e\n\u003ctd\u003e\u003ca href=\"https:\/\/download.lenovo.com\/pccbbs\/mobiles_pdf\/tp_p53_hmm_en.pdf\"\u003eLenovo ThinkPad P53 service documentation (download.lenovo.com, p. 96)\u003c\/a\u003e\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/table\u003e\u003ch3\u003eCheck Before Ordering\u003c\/h3\u003e\u003cp\u003eThread M2.5 x 0.45 mm, 8 mm long, head about 5 mm.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003eOurs is a black low-profile Phillips flat head, about 5 mm across (see the photo). Lenovo's document calls this a flat-head screw. Compare the head with your original before ordering.\u003c\/li\u003e\n\u003cli\u003eThe original screws have a nylon thread-lock patch; these do not. Add a drop of low-strength threadlocker if needed.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eWhy the Right Screw Matters\u003c\/h3\u003e\u003cp\u003eThread, length and head all have to match. A screw that is too long can push into the parts behind it (a battery, a board or the keyboard); one that is too short or has the wrong head will not hold. 10 screws cover the position with spares.\u003c\/p\u003e\u003ch3\u003eWhat You Get\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e10 x M2.5 x 8mm black low-profile Phillips flat head machine screws\u003c\/li\u003e\n\u003cli\u003eBrand new, bagged and labelled\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eSpecifications\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eThread Size:\u003c\/strong\u003e M2.5 x 0.45mm (metric coarse)\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eLength:\u003c\/strong\u003e 8mm\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eHead Style:\u003c\/strong\u003e Phillips flat head, low profile\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eHead Diameter:\u003c\/strong\u003e about 5mm\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eDrive:\u003c\/strong\u003e Phillips\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eMaterial:\u003c\/strong\u003e Carbon steel\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eFinish:\u003c\/strong\u003e Black oxide\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003ePack:\u003c\/strong\u003e 10 pieces\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003e\u003cstrong\u003eImportant:\u003c\/strong\u003e compatible-size replacement screws, not genuine Lenovo parts. Brand and model names are used only to describe fit. Please verify the size against your laptop's service manual or the original screw before ordering.\u003c\/p\u003e","brand":"TechSpareWarehouse","offers":[{"title":"10-Pack","offer_id":67746175975498,"sku":"M25X8-PFH-CS-BLK-10PK-LETPP53-LCD","price":4.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0691\/7351\/0218\/files\/s-l1600_a5ac1bc3-8aa7-4dd5-9d00-072ebce102c6.webp?v=1792459824"}],"url":"https:\/\/techsparewarehouse.com\/collections\/m2-5-x-8mm-screws.oembed","provider":"Techsparewarehouse","version":"1.0","type":"link"}