Acer Aspire 1810T screw size
M2 · 2.5 to 5 mm long
If you are replacing a screw on Acer Aspire 1810T, the thread is M2 in lengths from 2.5 to 5 mm.
There are 10 separate fitment records for it, including display (qty 4) (M2), unspecified (qty 7, shoulder, blue) (M2) and I/O board (qty 2) (M2), plus 7 more in the table below.
Head and drive, as the sources state them: shoulder screw head.
10 of the 10 records are marked confirmed, drawn from 1 source (tim.id.au).
An M2 screw is 2 mm in diameter with a 0.4 mm pitch, tapped with a 1.6 mm drill; imperial look-alike: #2-56 UNC (2.18 mm) is close but not interchangeable.
Acer Aspire 1810T screw specifications
One row per fitment record. Head, drive are shown only where the source states them; pitch is the ISO coarse pitch for the thread.
| Thread | Length | Pitch | Head | Drive | Where it goes | Status |
|---|---|---|---|---|---|---|
| M2 | 2.5 mm | 0.4 mm | not stated | not stated | Display (qty 4) | Confirmed |
| M2 | 2.5 mm | 0.4 mm | Shoulder screw | not stated | Unspecified (qty 7, shoulder, blue) | Confirmed |
| M2 | 3 mm | 0.4 mm | not stated | not stated | I/O board (qty 2) | Confirmed |
| M2 | 3 mm | 0.4 mm | not stated | not stated | LED board (qty 1) | Confirmed |
| M2 | 3 mm | 0.4 mm | not stated | not stated | Speaker (qty 4) | Confirmed |
| M2 | 3 mm | 0.4 mm | not stated | not stated | Unspecified (qty 18) | Confirmed |
| M2 | 3 mm | 0.4 mm | not stated | not stated | Wireless card (qty 1) | Confirmed |
| M2 | 5 mm | 0.4 mm | not stated | not stated | Display (qty 2) | Confirmed |
| M2 | 5 mm | 0.4 mm | not stated | not stated | Display bezel (qty 4) | Confirmed |
| M2 | 5 mm | 0.4 mm | not stated | not stated | Unspecified (qty 18) | Confirmed |
Fitment records and sources
Display (qty 4)
pitch 0.4 mm · tap 1.6 mm · clearance 2.4 mm · PH0 / Torx T6
Unspecified (qty 7, shoulder, blue)
pitch 0.4 mm · tap 1.6 mm · clearance 2.4 mm · PH0 / Torx T6
I/O board (qty 2)
pitch 0.4 mm · tap 1.6 mm · clearance 2.4 mm · PH0 / Torx T6
LED board (qty 1)
pitch 0.4 mm · tap 1.6 mm · clearance 2.4 mm · PH0 / Torx T6
Speaker (qty 4)
pitch 0.4 mm · tap 1.6 mm · clearance 2.4 mm · PH0 / Torx T6
Unspecified (qty 18)
pitch 0.4 mm · tap 1.6 mm · clearance 2.4 mm · PH0 / Torx T6
Wireless card (qty 1)
pitch 0.4 mm · tap 1.6 mm · clearance 2.4 mm · PH0 / Torx T6
Display (qty 2)
pitch 0.4 mm · tap 1.6 mm · clearance 2.4 mm · PH0 / Torx T6
Display bezel (qty 4)
pitch 0.4 mm · tap 1.6 mm · clearance 2.4 mm · PH0 / Torx T6
Unspecified (qty 18)
pitch 0.4 mm · tap 1.6 mm · clearance 2.4 mm · PH0 / Torx T6
How to check the screw before you buy
- Laptop covers and brackets often mix two or three lengths of the same thread, so lay the screws out in the order they came out (a magnetic mat or a sheet of paper with the hole pattern drawn on it works).
- Diameter: across the threads an M2 screw measures about 2 mm with calipers (usually a hair under). If yours measures noticeably more or less, it is a different thread.
- Pitch: 0.4 mm from one thread crest to the next (25 crests per centimetre). A thread pitch gauge or the pitch-gauge tool settles it in seconds.
- Length: for shoulder screw screws, measure from under the head to the tip (countersunk heads are the exception: they are measured overall).
- The records span 2.5–5 mm, which means different positions take different lengths — match each hole to its own screw.
- Driver: the source does not name the drive. Standard M2 heads take PH0 for Phillips and T6 for Torx, and a 1.5 mm hex key for socket heads; a bit that fits loosely will cam out and strip the head.
- Tightening: no device-specific torque is published in these records. The site's general figure for M2 is about 25-40 N·cm into metal threads and 12-20 N·cm into plastic bosses; snug it up and stop.
Common mix-ups with M2
- M.2 SSD mounting screws (M2 x 3mm) are frequently mislabeled generically as 'M.2 screws' which can be confused with the M2 metric thread designation — they do coincide numerically here but are conceptually distinct (M.2 = card format, M2 = thread size).
- The standard M.2 SSD screw is M2 x 3mm, but some laptops and handhelds use non-standard lengths or head shapes.
Buy these screws at TechSpare Warehouse
In stock and shipped from South Carolina. Our black screws are Phillips wafer head (low profile); match the head style and length to the original before you order.
-
M2 x 2.5mm Screws for Dell XPS 14 9440 M.2 SSD Drive – 10-Pack Black
$4.99 -
M2 x 2.5mm Screws for ASUS ROG Strix G17 G713 SSD WiFi Touchpad 10-Pack Black
$4.99
-
M2 x 3mm Screws for Dell XPS 13 9340 Base Cover SSD Shield 10-Pack Black
$4.99 -
10x M2 x 3mm Phillips Screws for Lenovo ThinkPad X131e Chromebook WiFi SSD
$4.99
-
M2 x 5mm Replacement Bottom Case Screws for Dell Inspiron 3535 Laptop 10-Pack
$4.99 -
M2 x 5mm Phillips Wafer Head Screw for Dell G16 7630 Gaming Laptop Repair - Pack of 100 Black
$7.99 -
ASUS ROG Strix G15 G513R Replacement Screws Sold Individually – M1.6 x 3mm, M2 x 2.5mm, M2 x 3mm, M2.5 x 6mm Phillips Wafer Head, Black
$0.10Choose size -
ASUS ROG Strix G17 G713 Replacement Screws Sold Individually – M1.6 x 3mm, M2 x 2.5mm, M2 x 3mm, M2.5 x 6mm Phillips Wafer Head, Black
$0.10Choose size
More in Laptops & PCs
The same screw also fits
Devices whose records share a thread with Acer Aspire 1810T, closest length match first.
- Dell Inspiron 15 5579 2-in-1 also M2 × 2.5 mm
- Dell Latitude 7389 2-in-1 also M2 × 3 mm
- Lenovo ideapad 720S-13ARR also M2 × 2.5 mm
- HP EliteBook x360 1040 G6 also M2 × 5 mm
- Lenovo ThinkPad P14s Gen 4 also M2 × 2.5 mm
- Lenovo ThinkPad Yoga 260 also M2 × 2.5 mm
- Chromebook bottom case also M2 × 3 mm
- Lenovo ThinkPad 4 also M2 × 2.5 mm
Questions about Acer Aspire 1810T screws
- What size screw does Acer Aspire 1810T use?
- M2 × 2.5 mm for display (qty 4); M2 × 2.5 mm for unspecified (qty 7, shoulder, blue); M2 × 3 mm for I/O board (qty 2); M2 × 3 mm for LED board (qty 1); M2 × 3 mm for speaker (qty 4); M2 × 3 mm for unspecified (qty 18); M2 × 3 mm for wireless card (qty 1); M2 × 5 mm for display (qty 2); M2 × 5 mm for display bezel (qty 4); M2 × 5 mm for unspecified (qty 18).
- How long are the screws in Acer Aspire 1810T?
- The records range from 2.5 to 5 mm depending on the position, so match each screw to its own hole.
- What is the thread pitch of an M2 screw?
- 0.4 mm (coarse), which is the standard pitch for M2 machine screws; a 0.25 mm fine pitch exists but is uncommon. The tap drill is 1.6 mm and the normal clearance hole is 2.4 mm.
- What screwdriver do I need for Acer Aspire 1810T?
- The sources do not name the drive. For M2, Phillips heads normally take PH0 and Torx heads T6; socket heads take a 1.5 mm hex key.
- Can I use an imperial screw instead of M2?
- No. Imperial look-alike: #2-56 UNC (2.18 mm) is close but not interchangeable. Use a true M2 screw so it does not cross-thread or strip the hole.
- Where can I buy replacement screws for Acer Aspire 1810T?
- TechSpareWarehouse (our own store) lists M2 x 2.5mm, M2 x 3mm and M2 x 5mm, which match lengths in the records above.