Acer Aspire 4530 screw size
M2 / M2.5 / M3 · 3 to 6.5 mm long
If you are replacing a screw on Acer Aspire 4530, the thread is M2, M2.5 and M3 in lengths from 3 to 6.5 mm.
There are 18 separate fitment records for it, including display (qty 4) (M2), optical drive (qty 2) (M2) and wireless card (qty 1) (M2), plus 15 more in the table below.
18 of the 18 records are marked confirmed, drawn from 1 source (tim.id.au).
An M2 screw is 2 mm in diameter with a 0.4 mm pitch, tapped with a 1.6 mm drill; imperial look-alike: #2-56 UNC (2.18 mm) is close but not interchangeable.
Acer Aspire 4530 screw specifications
One row per fitment record. Head, drive are shown only where the source states them; pitch is the ISO coarse pitch for the thread.
| Thread | Length | Pitch | Head | Drive | Where it goes | Status |
|---|---|---|---|---|---|---|
| M2 | 3 mm | 0.4 mm | not stated | not stated | Display (qty 4) | Confirmed |
| M2 | 3 mm | 0.4 mm | not stated | not stated | Optical drive (qty 2) | Confirmed |
| M2 | 3 mm | 0.4 mm | not stated | not stated | Wireless card (qty 1) | Confirmed |
| M2.5 | 3 mm | 0.45 mm | not stated | not stated | I/O board (qty 2) | Confirmed |
| M2.5 | 3 mm | 0.45 mm | not stated | not stated | Speaker (qty 7) | Confirmed |
| M2.5 | 4 mm | 0.45 mm | not stated | not stated | LED board (qty 1) | Confirmed |
| M2.5 | 4 mm | 0.45 mm | not stated | not stated | Hard drive (qty 2) | Confirmed |
| M2.5 | 4 mm | 0.45 mm | not stated | not stated | Heat sink (qty 1) | Confirmed |
| M2.5 | 4 mm | 0.45 mm | not stated | not stated | Speaker (qty 4) | Confirmed |
| M2.5 | 4 mm | 0.45 mm | not stated | not stated | System board (qty 2) | Confirmed |
| M2.5 | 4 mm | 0.45 mm | not stated | not stated | Unspecified (qty 28) | Confirmed |
| M2.5 | 4 mm | 0.45 mm | not stated | not stated | Wireless card (qty 2) | Confirmed |
| M2.5 | 5 mm | 0.45 mm | not stated | not stated | Display (qty 6) | Confirmed |
| M2.5 | 5 mm | 0.45 mm | not stated | not stated | Display bezel (qty 6) | Confirmed |
| M2.5 | 5 mm | 0.45 mm | not stated | not stated | Unspecified (qty 12) | Confirmed |
| M2.5 | 6.5 mm | 0.45 mm | not stated | not stated | Display (qty 4) | Confirmed |
| M2.5 | 6.5 mm | 0.45 mm | not stated | not stated | Unspecified (qty 15) | Confirmed |
| M3 | 3.5 mm | 0.5 mm | not stated | not stated | Hard drive (qty 4) | Confirmed |
Fitment records and sources
Display (qty 4)
pitch 0.4 mm · tap 1.6 mm · clearance 2.4 mm · PH0 / Torx T6
Optical drive (qty 2)
pitch 0.4 mm · tap 1.6 mm · clearance 2.4 mm · PH0 / Torx T6
Wireless card (qty 1)
pitch 0.4 mm · tap 1.6 mm · clearance 2.4 mm · PH0 / Torx T6
I/O board (qty 2)
pitch 0.45 mm · tap 2.05 mm · clearance 2.9 mm · PH1 / Torx T8
Speaker (qty 7)
pitch 0.45 mm · tap 2.05 mm · clearance 2.9 mm · PH1 / Torx T8
LED board (qty 1)
pitch 0.45 mm · tap 2.05 mm · clearance 2.9 mm · PH1 / Torx T8
Hard drive (qty 2)
pitch 0.45 mm · tap 2.05 mm · clearance 2.9 mm · PH1 / Torx T8
Heat sink (qty 1)
pitch 0.45 mm · tap 2.05 mm · clearance 2.9 mm · PH1 / Torx T8
Speaker (qty 4)
pitch 0.45 mm · tap 2.05 mm · clearance 2.9 mm · PH1 / Torx T8
System board (qty 2)
pitch 0.45 mm · tap 2.05 mm · clearance 2.9 mm · PH1 / Torx T8
Unspecified (qty 28)
pitch 0.45 mm · tap 2.05 mm · clearance 2.9 mm · PH1 / Torx T8
Wireless card (qty 2)
pitch 0.45 mm · tap 2.05 mm · clearance 2.9 mm · PH1 / Torx T8
Display (qty 6)
pitch 0.45 mm · tap 2.05 mm · clearance 2.9 mm · PH1 / Torx T8
Display bezel (qty 6)
pitch 0.45 mm · tap 2.05 mm · clearance 2.9 mm · PH1 / Torx T8
Unspecified (qty 12)
pitch 0.45 mm · tap 2.05 mm · clearance 2.9 mm · PH1 / Torx T8
Display (qty 4)
pitch 0.45 mm · tap 2.05 mm · clearance 2.9 mm · PH1 / Torx T8
Unspecified (qty 15)
pitch 0.45 mm · tap 2.05 mm · clearance 2.9 mm · PH1 / Torx T8
Hard drive (qty 4)
pitch 0.5 mm · tap 2.5 mm · clearance 3.4 mm · PH1 / Torx T10
How to check the screw before you buy
- Laptop covers and brackets often mix two or three lengths of the same thread, so lay the screws out in the order they came out (a magnetic mat or a sheet of paper with the hole pattern drawn on it works).
- Diameter: across the threads an M2 screw measures about 2 mm with calipers (usually a hair under). This device also uses M2.5 / M3, so measure each screw rather than assuming they match.
- Pitch: 0.4 mm from one thread crest to the next (25 crests per centimetre). A thread pitch gauge or the pitch-gauge tool settles it in seconds.
- Length: measure from under the head to the tip for pan, button, wafer and cap heads; countersunk (flat) heads are measured overall.
- The records span 3–6.5 mm, which means different positions take different lengths — match each hole to its own screw.
- Driver: the source does not name the drive. Standard M2 heads take PH0 for Phillips and T6 for Torx, and a 1.5 mm hex key for socket heads; a bit that fits loosely will cam out and strip the head.
- Tightening: no device-specific torque is published in these records. The site's general figure for M2 is about 25-40 N·cm into metal threads and 12-20 N·cm into plastic bosses; snug it up and stop.
Common mix-ups with M2 / M2.5 / M3
- The standard M.2 SSD screw is M2 x 3mm, but some laptops and handhelds use non-standard lengths or head shapes.
- M2.5 pitch is 0.45mm vs M3's 0.5mm and M2's 0.4mm — forcing the wrong one strips plastic bosses instantly.
- Thorlabs' 16mm cage system standard plates use dual 4-40 (UNC) and M3 taps on the same plate (e.g., SP01), so metric and imperial fasteners are both valid depending on the region/kit purchased.
Buy these screws at TechSpare Warehouse
In stock and shipped from South Carolina. Our black screws are Phillips wafer head (low profile); match the head style and length to the original before you order.
-
M2 x 3mm Screws for Dell XPS 13 9340 Base Cover SSD Shield 10-Pack Black
$4.99 -
10x M2 x 3mm Phillips Screws for Lenovo ThinkPad X131e Chromebook WiFi SSD
$4.99
-
25x M2.5 x 3mm Phillips Screws for Acer Nitro 5 SSD M.2 WiFi Card
$5.99 -
M2.5 x 4mm Screws for Lenovo IdeaPad 5 Pro 14 Display Hinge 10-Pack Black
$4.99 -
M2.5 x 4mm Screws for Lenovo IdeaPad 5 Pro 14 System Board Hinge 10-Pack Black
$4.99
-
ASUS ROG Strix G15 G513R Replacement Screws Sold Individually – M1.6 x 3mm, M2 x 2.5mm, M2 x 3mm, M2.5 x 6mm Phillips Wafer Head, Black
$0.10Choose size -
ASUS ROG Strix G17 G713 Replacement Screws Sold Individually – M1.6 x 3mm, M2 x 2.5mm, M2 x 3mm, M2.5 x 6mm Phillips Wafer Head, Black
$0.10Choose size
-
HP EliteBook 840 G8 Replacement Screws Sold Individually – M1.6 x 3mm, M2 x 2.5mm, M2 x 4mm, M2.5 x 4mm Phillips Wafer Head, Black
$0.10Choose size
More in Laptops & PCs
The same screw also fits
Devices whose records share a thread with Acer Aspire 4530, closest length match first.
- Lenovo 100e Chromebook also M2 × 3 mm
- HP EliteBook 845 G8 also M2.5 × 4 mm
- Lenovo Slim 7 14ILL10 also M2 × 3 mm
- HP 6710b also M2 × 3 mm
- Acer Aspire 4250 also M2 × 3 mm
- Dell Precision M4300 also M2 × 3 mm
- Lenovo IdeaPad Flex Pro-13IKB also M2 × 3 mm
- Lenovo Ideapad 100-15IBY also M2 × 3 mm
Questions about Acer Aspire 4530 screws
- What size screw does Acer Aspire 4530 use?
- M2 × 3 mm for display (qty 4); M2 × 3 mm for optical drive (qty 2); M2 × 3 mm for wireless card (qty 1); M2.5 × 3 mm for I/O board (qty 2); M2.5 × 3 mm for speaker (qty 7); M2.5 × 4 mm for LED board (qty 1); M2.5 × 4 mm for hard drive (qty 2); M2.5 × 4 mm for heat sink (qty 1); M2.5 × 4 mm for speaker (qty 4); M2.5 × 4 mm for system board (qty 2); M2.5 × 4 mm for unspecified (qty 28); M2.5 × 4 mm for wireless card (qty 2); M2.5 × 5 mm for display (qty 6); M2.5 × 5 mm for display bezel (qty 6); M2.5 × 5 mm for unspecified (qty 12); M2.5 × 6.5 mm for display (qty 4); M2.5 × 6.5 mm for unspecified (qty 15); M3 × 3.5 mm for hard drive (qty 4).
- How long are the screws in Acer Aspire 4530?
- The records range from 3 to 6.5 mm depending on the position, so match each screw to its own hole.
- What is the thread pitch of an M2 screw?
- 0.4 mm (coarse), which is the standard pitch for M2 machine screws; a 0.25 mm fine pitch exists but is uncommon. The tap drill is 1.6 mm and the normal clearance hole is 2.4 mm.
- What screwdriver do I need for Acer Aspire 4530?
- The sources do not name the drive. For M2, Phillips heads normally take PH0 and Torx heads T6; socket heads take a 1.5 mm hex key.
- Can I use an imperial screw instead of M2?
- No. Imperial look-alike: #2-56 UNC (2.18 mm) is close but not interchangeable. Use a true M2 screw so it does not cross-thread or strip the hole.
- Where can I buy replacement screws for Acer Aspire 4530?
- TechSpareWarehouse (our own store) lists M2 x 3mm, M2.5 x 3mm and M2.5 x 4mm, which match lengths in the records above.