Acer Aspire 4740G screw size

Acer Aspire 4740G screw specifications

One row per fitment record. Head, drive are shown only where the source states them; pitch is the ISO coarse pitch for the thread.

How to check the screw before you buy

1. Laptop covers and brackets often mix two or three lengths of the same thread, so lay the screws out in the order they came out (a magnetic mat or a sheet of paper with the hole pattern drawn on it works).
2. Diameter: across the threads an M2 screw measures about 2 mm with calipers (usually a hair under). This device also uses M2.5 / M3, so measure each screw rather than assuming they match.
3. Pitch: 0.4 mm from one thread crest to the next (25 crests per centimetre). A thread pitch gauge or the pitch-gauge tool settles it in seconds.
4. Length: measure from under the head to the tip for pan, button, wafer and cap heads; countersunk (flat) heads are measured overall.
5. The records span 3–10 mm, which means different positions take different lengths — match each hole to its own screw.
6. Driver: the source does not name the drive. Standard M2 heads take PH0 for Phillips and T6 for Torx, and a 1.5 mm hex key for socket heads; a bit that fits loosely will cam out and strip the head.
7. Tightening: no device-specific torque is published in these records. The site's general figure for M2 is about 25-40 N·cm into metal threads and 12-20 N·cm into plastic bosses; snug it up and stop.

Pitch gauge · Screw size finder · Torque guide

More in Laptops & PCs

The same screw also fits

Devices whose records share a thread with Acer Aspire 4740G, closest length match first.

• HP Chromebook 14 G7 (id 38457196) also M2.5 × 3 mm
• HP EliteBook 840 G6 also M2 × 3 mm
• HP 246 G4 also M2 × 3 mm
• Lenovo E40-80 also M2 × 3 mm
• Acer TravelMate 5710 also M2 × 3 mm
• Lenovo Y70-80 Touch also M2 × 3 mm
• Lenovo E51-80 also M2 × 3 mm
• Lenovo ThinkPad L14 Gen 2 also M2 × 3 mm

Questions about Acer Aspire 4740G screws

What size screw does Acer Aspire 4740G use?

M2 × 3 mm for display (qty 6); M2 × 3 mm for hinge (qty 2); M2 × 3 mm for optical drive (qty 2); M2 × 3 mm for touchpad (qty 2); M2 × 3 mm for unspecified (qty 18); M2 × 3 mm for wireless card (qty 2); M2.5 × 10 mm for unspecified (qty 10); M2.5 × 3 mm for I/O board (qty 1); M2.5 × 3 mm for camera (qty 1); M2.5 × 3 mm for display (qty 1); M2.5 × 3 mm for speaker (qty 2); M2.5 × 3 mm for system board (qty 1); M2.5 × 3 mm for unspecified (qty 12); M2.5 × 3 mm for wireless card (qty 1); M2.5 × 3.2 mm for heat sink (qty 4); M2.5 × 5 mm for display (qty 2); M2.5 × 5 mm for display bezel (qty 6); M2.5 × 5 mm for hinge (qty 2); M2.5 × 5 mm for optical drive (qty 1); M2.5 × 5 mm for unspecified (qty.

How long are the screws in Acer Aspire 4740G?

The records range from 3 to 10 mm depending on the position, so match each screw to its own hole.

What is the thread pitch of an M2 screw?

0.4 mm (coarse), which is the standard pitch for M2 machine screws; a 0.25 mm fine pitch exists but is uncommon. The tap drill is 1.6 mm and the normal clearance hole is 2.4 mm.

What screwdriver do I need for Acer Aspire 4740G?

The sources do not name the drive. For M2, Phillips heads normally take PH0 and Torx heads T6; socket heads take a 1.5 mm hex key.

Can I use an imperial screw instead of M2?

No. Imperial look-alike: #2-56 UNC (2.18 mm) is close but not interchangeable. Use a true M2 screw so it does not cross-thread or strip the hole.

Where can I buy replacement screws for Acer Aspire 4740G?

TechSpareWarehouse (our own store) lists M2 x 3mm, M2.5 x 10mm and M2.5 x 3mm, which match lengths in the records above.