Acer Aspire 5630 screw size
M2.5 · 10 to 15 mm long
If you are replacing a screw on Acer Aspire 5630, the thread is M2.5 in lengths from 10 to 15 mm.
There are 2 separate fitment records for it, including display (qty 4, yellow) (M2.5) and display (qty 4, yellow) (M2.5).
2 of the 2 records are marked confirmed, drawn from 1 source (tim.id.au).
For reference, M2.5 is 2.5 mm across the threads at 0.45 mm pitch. The imperial size people confuse it with: #3-48 / #4-40 (2.51 / 2.84 mm) — #4-40 is the common US stand-in and it will NOT thread in.
Acer Aspire 5630 screw specifications
One row per fitment record. Head, drive are shown only where the source states them; pitch is the ISO coarse pitch for the thread.
| Thread | Length | Pitch | Head | Drive | Where it goes | Status |
|---|---|---|---|---|---|---|
| M2.5 | 10 mm | 0.45 mm | not stated | not stated | Display (qty 4, yellow) | Confirmed |
| M2.5 | 15 mm | 0.45 mm | not stated | not stated | Display (qty 4, yellow) | Confirmed |
Fitment records and sources
Display (qty 4, yellow)
pitch 0.45 mm · tap 2.05 mm · clearance 2.9 mm · PH1 / Torx T8
Display (qty 4, yellow)
pitch 0.45 mm · tap 2.05 mm · clearance 2.9 mm · PH1 / Torx T8
How to check the screw before you buy
- Laptop covers and brackets often mix two or three lengths of the same thread, so lay the screws out in the order they came out (a magnetic mat or a sheet of paper with the hole pattern drawn on it works).
- Diameter: across the threads an M2.5 screw measures about 2.5 mm with calipers (usually a hair under). If yours measures noticeably more or less, it is a different thread.
- Pitch: 0.45 mm from one thread crest to the next (22.22 crests per centimetre). A thread pitch gauge or the pitch-gauge tool settles it in seconds.
- Length: measure from under the head to the tip for pan, button, wafer and cap heads; countersunk (flat) heads are measured overall.
- The records span 10–15 mm, which means different positions take different lengths — match each hole to its own screw.
- Driver: the source does not name the drive. Standard M2.5 heads take PH1 for Phillips and T8 for Torx, and a 2 mm hex key for socket heads; a bit that fits loosely will cam out and strip the head.
- Tightening: no device-specific torque is published in these records. The site's general figure for M2.5 is about 45-70 N·cm into metal threads and 20-35 N·cm into plastic bosses; snug it up and stop.
Common mix-ups with M2.5
- M2.5 pitch is 0.45mm vs M3's 0.5mm and M2's 0.4mm — forcing the wrong one strips plastic bosses instantly.
- M2.5 and M3 look the same to the naked eye — you need calipers on the shank to tell them apart.
Buy these screws at TechSpare Warehouse
In stock and shipped from South Carolina. Our black screws are Phillips wafer head (low profile); match the head style and length to the original before you order.
-
M2.5 x 10mm Phillips Wafer Head Screw for Turntable Cartridge Headshell Mount - Pack of 50 Black
$5.99 -
M2.5 x 10mm Phillips Wafer Head Screw for ASUS TUF Gaming A15/F15 Laptop Repair - Single Replacement Black
$0.10 each · min. 50
-
M2.5 x 10mm Phillips Wafer Head Screw for Laptop Bottom Cover Replacement - Single Replacement Black
$0.10 each · min. 50
More in Laptops & PCs
The same screw also fits
Devices whose records share a thread with Acer Aspire 5630, closest length match first.
- Lenovo ThinkPad SL500c also M2.5 × 10 mm
- Lenovo IdeaPad Y410p also M2.5 × 10 mm
- HP Compaq 6730s also M2.5 × 10 mm
- Acer Aspire 5680 also M2.5 × 10 mm
- HP nx7400 also M2.5 × 10 mm
- Acer Aspire 5735Z also M2.5 × 10 mm
- HP Compaq 6735b also M2.5 × 10 mm
- Acer Aspire 5735 also M2.5 × 10 mm
Questions about Acer Aspire 5630 screws
- What size screw does Acer Aspire 5630 use?
- M2.5 × 10 mm for display (qty 4, yellow); M2.5 × 15 mm for display (qty 4, yellow).
- How long are the screws in Acer Aspire 5630?
- The records range from 10 to 15 mm depending on the position, so match each screw to its own hole.
- What is the thread pitch of an M2.5 screw?
- 0.45 mm (coarse), which is the standard pitch for M2.5 machine screws; a 0.35 mm fine pitch exists but is uncommon. The tap drill is 2.05 mm and the normal clearance hole is 2.9 mm.
- What screwdriver do I need for Acer Aspire 5630?
- The sources do not name the drive. For M2.5, Phillips heads normally take PH1 and Torx heads T8; socket heads take a 2 mm hex key.
- Can I use an imperial screw instead of M2.5?
- No. Imperial look-alike: #3-48 / #4-40 (2.51 / 2.84 mm) — #4-40 is the common US stand-in and it will NOT thread in. Use a true M2.5 screw so it does not cross-thread or strip the hole.
- Where can I buy replacement screws for Acer Aspire 5630?
- TechSpareWarehouse (our own store) lists M2.5 x 10mm, which matches the length in the records above.