Anbernic RG35XX rear case screws screw size
M1.2 · 3 to 4 mm long
Anbernic RG35XX rear case screws takes M1.2 metric screws in lengths from 3 to 4 mm.
Where it is used: six tiny hex-drive screws holding the back shell.
This entry is marked confirmed and comes from ifixit.com.
An M1.2 screw is 1.2 mm in diameter with a 0.25 mm pitch, tapped with a 0.95 mm drill; imperial look-alike: #0-80 UNF (1.52 mm) is the closest imperial screw, but it is bigger — not a substitute.
Anbernic RG35XX rear case screws screw specifications
One row per fitment record. Head, drive are shown only where the source states them; pitch is the ISO coarse pitch for the thread.
| Thread | Length | Pitch | Head | Drive | Where it goes | Status |
|---|---|---|---|---|---|---|
| M1.2 | 3–4 mm | 0.25 mm | not stated | not stated | Six tiny hex-drive screws holding the back shell | Confirmed |
Fitment records and sources
Six tiny hex-drive screws holding the back shell
pitch 0.25 mm · tap 0.95 mm · clearance 1.4 mm · PH000 / JIS 00 / Torx T1–T2
How to check the screw before you buy
- Over-long screws in phones are a known cause of damaged boards (Apple's 'long screw damage'), so never swap positions.
- Diameter: across the threads an M1.2 screw measures about 1.2 mm with calipers (usually a hair under). If yours measures noticeably more or less, it is a different thread.
- Pitch: 0.25 mm from one thread crest to the next (40 crests per centimetre). A thread pitch gauge or the pitch-gauge tool settles it in seconds.
- Length: measure from under the head to the tip for pan, button, wafer and cap heads; countersunk (flat) heads are measured overall.
- The records span 3–4 mm, which means different positions take different lengths — match each hole to its own screw.
- Driver: the source does not name the drive. Standard M1.2 heads take PH000 / JIS 00 for Phillips and T1–T2 for Torx; a bit that fits loosely will cam out and strip the head.
- Tightening: no device-specific torque is published in these records. The site's general figure for M1.2 is about 5-8 N·cm into metal threads and 3-5 N·cm into plastic bosses; snug it up and stop.
Common mix-ups with M1.2
- M1.2 and M1.4 look identical in an eyeglass repair kit — the wrong one strips soft acetate or metal hinges.
Buy these screws at TechSpare Warehouse
In stock and shipped from South Carolina. Our black screws are Phillips wafer head (low profile); match the head style and length to the original before you order.
More in Phones, Tablets & Wearables
The same screw also fits
Devices whose records share a thread with Anbernic RG35XX rear case screws, closest length match first.
- Watch strap keepers also M1.2 × 3–4 mm
- Watch casebacks & bracelet links also M1.2 × 3 mm
- Ultrabook internals also M1.2 × 3 mm
- Arduino / small PCB stacks also M1.2 × 3–4 mm
- Wireless earbud charging case hinge also M1.2 × 3 mm
- Eyeglass hinge / eyewire screw also M1.2 × 3 mm
- HP ProBook 635 Aero G8 also M1.2 × 3 mm
- Laptop/keyboard/phone repair micro screws also M1.2 × 3–4 mm
Questions about Anbernic RG35XX rear case screws screws
- What size screw does Anbernic RG35XX rear case screws use?
- M1.2 × 3–4 mm for six tiny hex-drive screws holding the back shell.
- How long are the screws in Anbernic RG35XX rear case screws?
- The records range from 3 to 4 mm depending on the position, so match each screw to its own hole.
- What is the thread pitch of an M1.2 screw?
- 0.25 mm (coarse), which is the standard pitch for M1.2 machine screws. The tap drill is 0.95 mm and the normal clearance hole is 1.4 mm.
- What screwdriver do I need for Anbernic RG35XX rear case screws?
- The sources do not name the drive. For M1.2, Phillips heads normally take PH000 / JIS 00 and Torx heads T1–T2.
- Can I use an imperial screw instead of M1.2?
- No. Imperial look-alike: #0-80 UNF (1.52 mm) is the closest imperial screw, but it is bigger — not a substitute. Use a true M1.2 screw so it does not cross-thread or strip the hole.