ASUS M6000 screw size
M2 / M2.5 · 3 to 6 mm long
ASUS M6000 takes M2 and M2.5 metric screws in lengths from 3 to 6 mm.
There are 17 separate fitment records for it, including base cover (qty 16, black) (M2), display (qty 8, black) (M2) and memory (qty 2, black) (M2), plus 14 more in the table below.
17 of the 17 records are marked confirmed, drawn from 1 source (tim.id.au).
An M2 screw is 2 mm in diameter with a 0.4 mm pitch, tapped with a 1.6 mm drill; imperial look-alike: #2-56 UNC (2.18 mm) is close but not interchangeable.
ASUS M6000 screw specifications
One row per fitment record. Head, drive are shown only where the source states them; pitch is the ISO coarse pitch for the thread.
| Thread | Length | Pitch | Head | Drive | Where it goes | Status |
|---|---|---|---|---|---|---|
| M2 | 3 mm | 0.4 mm | not stated | not stated | Base cover (qty 16, black)black finish | Confirmed |
| M2 | 3 mm | 0.4 mm | not stated | not stated | Display (qty 8, black)black finish | Confirmed |
| M2 | 3 mm | 0.4 mm | not stated | not stated | Memory (qty 2, black)black finish | Confirmed |
| M2 | 3 mm | 0.4 mm | not stated | not stated | Palm rest (qty 5, black)black finish | Confirmed |
| M2 | 3 mm | 0.4 mm | not stated | not stated | System board (qty 2, black)black finish | Confirmed |
| M2 | 3 mm | 0.4 mm | not stated | not stated | Touchpad (qty 5, black)black finish | Confirmed |
| M2 | 3 mm | 0.4 mm | not stated | not stated | Wireless card (qty 1, black)black finish | Confirmed |
| M2 | 6 mm | 0.4 mm | not stated | not stated | Base cover (qty 7, black)black finish | Confirmed |
| M2 | 6 mm | 0.4 mm | not stated | not stated | Display (qty 8, black)black finish | Confirmed |
| M2 | 6 mm | 0.4 mm | not stated | not stated | Hard drive (qty 2, black)black finish | Confirmed |
| M2 | 6 mm | 0.4 mm | not stated | not stated | Speaker (qty 1, black)black finish | Confirmed |
| M2 | 6 mm | 0.4 mm | not stated | not stated | System board (qty 6, black)black finish | Confirmed |
| M2 | 6 mm | 0.4 mm | not stated | not stated | Unspecified (qty 4, black)black finish | Confirmed |
| M2.5 | 4 mm | 0.45 mm | not stated | not stated | Display (qty 8, black)black finish | Confirmed |
| M2.5 | 4 mm | 0.45 mm | not stated | not stated | System board (qty 2, black)black finish | Confirmed |
| M2.5 | 6 mm | 0.45 mm | not stated | not stated | Base cover (qty 2, black)black finish | Confirmed |
| M2.5 | 6 mm | 0.45 mm | not stated | not stated | Display (qty 4, black)black finish | Confirmed |
Fitment records and sources
Base cover (qty 16, black)
pitch 0.4 mm · tap 1.6 mm · clearance 2.4 mm · PH0 / Torx T6
Display (qty 8, black)
pitch 0.4 mm · tap 1.6 mm · clearance 2.4 mm · PH0 / Torx T6
Memory (qty 2, black)
pitch 0.4 mm · tap 1.6 mm · clearance 2.4 mm · PH0 / Torx T6
Palm rest (qty 5, black)
pitch 0.4 mm · tap 1.6 mm · clearance 2.4 mm · PH0 / Torx T6
System board (qty 2, black)
pitch 0.4 mm · tap 1.6 mm · clearance 2.4 mm · PH0 / Torx T6
Touchpad (qty 5, black)
pitch 0.4 mm · tap 1.6 mm · clearance 2.4 mm · PH0 / Torx T6
Wireless card (qty 1, black)
pitch 0.4 mm · tap 1.6 mm · clearance 2.4 mm · PH0 / Torx T6
Base cover (qty 7, black)
pitch 0.4 mm · tap 1.6 mm · clearance 2.4 mm · PH0 / Torx T6
Display (qty 8, black)
pitch 0.4 mm · tap 1.6 mm · clearance 2.4 mm · PH0 / Torx T6
Hard drive (qty 2, black)
pitch 0.4 mm · tap 1.6 mm · clearance 2.4 mm · PH0 / Torx T6
Speaker (qty 1, black)
pitch 0.4 mm · tap 1.6 mm · clearance 2.4 mm · PH0 / Torx T6
System board (qty 6, black)
pitch 0.4 mm · tap 1.6 mm · clearance 2.4 mm · PH0 / Torx T6
Unspecified (qty 4, black)
pitch 0.4 mm · tap 1.6 mm · clearance 2.4 mm · PH0 / Torx T6
Display (qty 8, black)
pitch 0.45 mm · tap 2.05 mm · clearance 2.9 mm · PH1 / Torx T8
System board (qty 2, black)
pitch 0.45 mm · tap 2.05 mm · clearance 2.9 mm · PH1 / Torx T8
Base cover (qty 2, black)
pitch 0.45 mm · tap 2.05 mm · clearance 2.9 mm · PH1 / Torx T8
Display (qty 4, black)
pitch 0.45 mm · tap 2.05 mm · clearance 2.9 mm · PH1 / Torx T8
How to check the screw before you buy
- A screw that is even 1 mm too long in a laptop base can push into the keyboard, battery or a board trace, so match the length position by position.
- Diameter: across the threads an M2 screw measures about 2 mm with calipers (usually a hair under). This device also uses M2.5, so measure each screw rather than assuming they match.
- Pitch: 0.4 mm from one thread crest to the next (25 crests per centimetre). A thread pitch gauge or the pitch-gauge tool settles it in seconds.
- Length: measure from under the head to the tip for pan, button, wafer and cap heads; countersunk (flat) heads are measured overall.
- The records span 3–6 mm, which means different positions take different lengths — match each hole to its own screw.
- Driver: the source does not name the drive. Standard M2 heads take PH0 for Phillips and T6 for Torx, and a 1.5 mm hex key for socket heads; a bit that fits loosely will cam out and strip the head.
- Tightening: no device-specific torque is published in these records. The site's general figure for M2 is about 25-40 N·cm into metal threads and 12-20 N·cm into plastic bosses; snug it up and stop.
Common mix-ups with M2 / M2.5
- ASUS ROG Ally screw sizes circulating online (M2x16, M2x10) come from a community Q&A, not an ASUS manual — measure before ordering.
- M.2 SSD mounting screws (M2 x 3mm) are frequently mislabeled generically as 'M.2 screws' which can be confused with the M2 metric thread designation — they do coincide numerically here but are conceptually distinct (M.2 = card format, M2 = thread size).
- M2.5 and M3 look the same to the naked eye — you need calipers on the shank to tell them apart.
- M2.5 pitch is 0.45mm vs M3's 0.5mm and M2's 0.4mm — forcing the wrong one strips plastic bosses instantly.
Buy these screws at TechSpare Warehouse
In stock and shipped from South Carolina. Our black screws are Phillips wafer head (low profile); match the head style and length to the original before you order.
-
M2 x 3mm Screws for Dell XPS 13 9340 Base Cover SSD Shield 10-Pack Black
$4.99 -
10x M2 x 3mm Phillips Screws for Lenovo ThinkPad X131e Chromebook WiFi SSD
$4.99
-
M2 x 6mm Phillips Wafer Head Screw for HP Omen Gaming Laptop Repair - Pack of 100 Black
$7.99 -
M2 x 6mm Phillips Wafer Head Screw for Audiophile Headphone Headband Repair - Pack of 50 Black
$4.99
-
M2.5 x 4mm Screws for Lenovo IdeaPad 5 Pro 14 Display Hinge 10-Pack Black
$4.99 -
M2.5 x 4mm Screws for Lenovo IdeaPad 5 Pro 14 System Board Hinge 10-Pack Black
$4.99
-
ASUS ROG Strix G15 G513R Replacement Screws Sold Individually – M1.6 x 3mm, M2 x 2.5mm, M2 x 3mm, M2.5 x 6mm Phillips Wafer Head, Black
$0.10Choose size -
ASUS ROG Strix G17 G713 Replacement Screws Sold Individually – M1.6 x 3mm, M2 x 2.5mm, M2 x 3mm, M2.5 x 6mm Phillips Wafer Head, Black
$0.10Choose size
More in Laptops & PCs
The same screw also fits
Devices whose records share a thread with ASUS M6000, closest length match first.
- HP Compaq nx4800 PC Compaq Presario V2000 also M2 × 3 mm
- HP Compaq nw8000 also M2 × 6 mm
- Lenovo ideapad 320L-17ABR also M2 × 3 mm
- Lenovo IdeaPad S415 also M2 × 3 mm
- Lenovo ThinkPad Edge E520 also M2 × 3 mm
- Lenovo ideapad 330-15AST also M2 × 3 mm
- HP 255 G1 also M2 × 3 mm
- Lenovo ThinkPad R500 also M2 × 3 mm
Questions about ASUS M6000 screws
- What size screw does ASUS M6000 use?
- M2 × 3 mm for base cover (qty 16, black); M2 × 3 mm for display (qty 8, black); M2 × 3 mm for memory (qty 2, black); M2 × 3 mm for palm rest (qty 5, black); M2 × 3 mm for system board (qty 2, black); M2 × 3 mm for touchpad (qty 5, black); M2 × 3 mm for wireless card (qty 1, black); M2 × 6 mm for base cover (qty 7, black); M2 × 6 mm for display (qty 8, black); M2 × 6 mm for hard drive (qty 2, black); M2 × 6 mm for speaker (qty 1, black); M2 × 6 mm for system board (qty 6, black); M2 × 6 mm for unspecified (qty 4, black); M2.5 × 4 mm for display (qty 8, black); M2.5 × 4 mm for system board (qty 2, black); M2.5 × 6 mm for base cover (qty 2, black); M2.5 × 6 mm for display (qty 4, black).
- How long are the screws in ASUS M6000?
- The records range from 3 to 6 mm depending on the position, so match each screw to its own hole.
- What is the thread pitch of an M2 screw?
- 0.4 mm (coarse), which is the standard pitch for M2 machine screws; a 0.25 mm fine pitch exists but is uncommon. The tap drill is 1.6 mm and the normal clearance hole is 2.4 mm.
- What screwdriver do I need for ASUS M6000?
- The sources do not name the drive. For M2, Phillips heads normally take PH0 and Torx heads T6; socket heads take a 1.5 mm hex key.
- Can I use an imperial screw instead of M2?
- No. Imperial look-alike: #2-56 UNC (2.18 mm) is close but not interchangeable. Use a true M2 screw so it does not cross-thread or strip the hole.
- Where can I buy replacement screws for ASUS M6000?
- TechSpareWarehouse (our own store) lists M2 x 3mm, M2 x 6mm and M2.5 x 4mm, which match lengths in the records above.