ASUS S62 screw size
M2 / M2.5 / M3 · 3 to 6 mm long
ASUS S62 takes M2, M2.5 and M3 metric screws in lengths from 3 to 6 mm.
There are 23 separate fitment records for it, including bracket (qty 1, black) (M2), display (qty 4, black) (M2) and memory (qty 4, black) (M2), plus 20 more in the table below.
23 of the 23 records are marked confirmed, drawn from 1 source (tim.id.au).
An M2 screw is 2 mm in diameter with a 0.4 mm pitch, tapped with a 1.6 mm drill; imperial look-alike: #2-56 UNC (2.18 mm) is close but not interchangeable.
ASUS S62 screw specifications
One row per fitment record. Head, drive are shown only where the source states them; pitch is the ISO coarse pitch for the thread.
| Thread | Length | Pitch | Head | Drive | Where it goes | Status |
|---|---|---|---|---|---|---|
| M2 | 3 mm | 0.4 mm | not stated | not stated | Bracket (qty 1, black)black finish | Confirmed |
| M2 | 3 mm | 0.4 mm | not stated | not stated | Display (qty 4, black)black finish | Confirmed |
| M2 | 3 mm | 0.4 mm | not stated | not stated | Memory (qty 4, black)black finish | Confirmed |
| M2 | 3 mm | 0.4 mm | not stated | not stated | Palm rest (qty 1, black)black finish | Confirmed |
| M2 | 3 mm | 0.4 mm | not stated | not stated | System board (qty 2, black)black finish | Confirmed |
| M2 | 3 mm | 0.4 mm | not stated | not stated | Unspecified (qty 4, black)black finish | Confirmed |
| M2 | 4 mm | 0.4 mm | not stated | not stated | Display (qty 1, white,black)black finish | Confirmed |
| M2 | 6 mm | 0.4 mm | not stated | not stated | Hinge (qty 2) | Confirmed |
| M2 | 6 mm | 0.4 mm | not stated | not stated | Unspecified (qty 2) | Confirmed |
| M2.5 | 3 mm | 0.45 mm | not stated | not stated | Display (qty 2, black)black finish | Confirmed |
| M2.5 | 4 mm | 0.45 mm | not stated | not stated | Base cover (qty 1, black)black finish | Confirmed |
| M2.5 | 4 mm | 0.45 mm | not stated | not stated | Display (qty 5, black)black finish | Confirmed |
| M2.5 | 4 mm | 0.45 mm | not stated | not stated | Hard drive (qty 3, black)black finish | Confirmed |
| M2.5 | 4 mm | 0.45 mm | not stated | not stated | Memory (qty 2, black)black finish | Confirmed |
| M2.5 | 4 mm | 0.45 mm | not stated | not stated | Optical drive (qty 1, black)black finish | Confirmed |
| M2.5 | 4 mm | 0.45 mm | not stated | not stated | Palm rest (qty 5, black)black finish | Confirmed |
| M2.5 | 4 mm | 0.45 mm | not stated | not stated | System board (qty 2, black)black finish | Confirmed |
| M2.5 | 4 mm | 0.45 mm | not stated | not stated | Unspecified (qty 3, black)black finish | Confirmed |
| M2.5 | 6 mm | 0.45 mm | not stated | not stated | Base cover (qty 15, black)black finish | Confirmed |
| M2.5 | 6 mm | 0.45 mm | not stated | not stated | Display (qty 7, black)black finish | Confirmed |
| M2.5 | 6 mm | 0.45 mm | not stated | not stated | Hinge (qty 2, black)black finish | Confirmed |
| M2.5 | 6 mm | 0.45 mm | not stated | not stated | Unspecified (qty 1, black)black finish | Confirmed |
| M3 | 4 mm | 0.5 mm | not stated | not stated | Hard drive (qty 4) | Confirmed |
Fitment records and sources
Bracket (qty 1, black)
pitch 0.4 mm · tap 1.6 mm · clearance 2.4 mm · PH0 / Torx T6
Display (qty 4, black)
pitch 0.4 mm · tap 1.6 mm · clearance 2.4 mm · PH0 / Torx T6
Memory (qty 4, black)
pitch 0.4 mm · tap 1.6 mm · clearance 2.4 mm · PH0 / Torx T6
Palm rest (qty 1, black)
pitch 0.4 mm · tap 1.6 mm · clearance 2.4 mm · PH0 / Torx T6
System board (qty 2, black)
pitch 0.4 mm · tap 1.6 mm · clearance 2.4 mm · PH0 / Torx T6
Unspecified (qty 4, black)
pitch 0.4 mm · tap 1.6 mm · clearance 2.4 mm · PH0 / Torx T6
Display (qty 1, white,black)
pitch 0.4 mm · tap 1.6 mm · clearance 2.4 mm · PH0 / Torx T6
Hinge (qty 2)
pitch 0.4 mm · tap 1.6 mm · clearance 2.4 mm · PH0 / Torx T6
Unspecified (qty 2)
pitch 0.4 mm · tap 1.6 mm · clearance 2.4 mm · PH0 / Torx T6
Display (qty 2, black)
pitch 0.45 mm · tap 2.05 mm · clearance 2.9 mm · PH1 / Torx T8
Base cover (qty 1, black)
pitch 0.45 mm · tap 2.05 mm · clearance 2.9 mm · PH1 / Torx T8
Display (qty 5, black)
pitch 0.45 mm · tap 2.05 mm · clearance 2.9 mm · PH1 / Torx T8
Hard drive (qty 3, black)
pitch 0.45 mm · tap 2.05 mm · clearance 2.9 mm · PH1 / Torx T8
Memory (qty 2, black)
pitch 0.45 mm · tap 2.05 mm · clearance 2.9 mm · PH1 / Torx T8
Optical drive (qty 1, black)
pitch 0.45 mm · tap 2.05 mm · clearance 2.9 mm · PH1 / Torx T8
Palm rest (qty 5, black)
pitch 0.45 mm · tap 2.05 mm · clearance 2.9 mm · PH1 / Torx T8
System board (qty 2, black)
pitch 0.45 mm · tap 2.05 mm · clearance 2.9 mm · PH1 / Torx T8
Unspecified (qty 3, black)
pitch 0.45 mm · tap 2.05 mm · clearance 2.9 mm · PH1 / Torx T8
Base cover (qty 15, black)
pitch 0.45 mm · tap 2.05 mm · clearance 2.9 mm · PH1 / Torx T8
Display (qty 7, black)
pitch 0.45 mm · tap 2.05 mm · clearance 2.9 mm · PH1 / Torx T8
Hinge (qty 2, black)
pitch 0.45 mm · tap 2.05 mm · clearance 2.9 mm · PH1 / Torx T8
Unspecified (qty 1, black)
pitch 0.45 mm · tap 2.05 mm · clearance 2.9 mm · PH1 / Torx T8
Hard drive (qty 4)
pitch 0.5 mm · tap 2.5 mm · clearance 3.4 mm · PH1 / Torx T10
How to check the screw before you buy
- A screw that is even 1 mm too long in a laptop base can push into the keyboard, battery or a board trace, so match the length position by position.
- Diameter: across the threads an M2 screw measures about 2 mm with calipers (usually a hair under). This device also uses M2.5 / M3, so measure each screw rather than assuming they match.
- Pitch: 0.4 mm from one thread crest to the next (25 crests per centimetre). A thread pitch gauge or the pitch-gauge tool settles it in seconds.
- Length: measure from under the head to the tip for pan, button, wafer and cap heads; countersunk (flat) heads are measured overall.
- The records span 3–6 mm, which means different positions take different lengths — match each hole to its own screw.
- Driver: the source does not name the drive. Standard M2 heads take PH0 for Phillips and T6 for Torx, and a 1.5 mm hex key for socket heads; a bit that fits loosely will cam out and strip the head.
- Tightening: no device-specific torque is published in these records. The site's general figure for M2 is about 25-40 N·cm into metal threads and 12-20 N·cm into plastic bosses; snug it up and stop.
Common mix-ups with M2 / M2.5 / M3
- The standard M.2 SSD screw is M2 x 3mm, but some laptops and handhelds use non-standard lengths or head shapes.
- M2.5 pitch is 0.45mm vs M3's 0.5mm and M2's 0.4mm — forcing the wrong one strips plastic bosses instantly.
- PC cases mix M3 (fans, optical and 2.5in drives) with imperial 6-32 (3.5in drives, motherboard standoffs) - don't force one into the other.
Buy these screws at TechSpare Warehouse
In stock and shipped from South Carolina. Our black screws are Phillips wafer head (low profile); match the head style and length to the original before you order.
-
M2 x 3mm Screws for Dell XPS 13 9340 Base Cover SSD Shield 10-Pack Black
$4.99 -
10x M2 x 3mm Phillips Screws for Lenovo ThinkPad X131e Chromebook WiFi SSD
$4.99
-
M2 x 4mm Phillips Wafer Head Machine Screws Black 50-Pack Laptop SSD Repair
$4.49 each · min. 2
-
M2 x 4mm Screws for Dell Latitude 5530 SSD Type-C Bracket 10-Pack Black
$4.99
-
M2 x 6mm Phillips Wafer Head Screw for HP Omen Gaming Laptop Repair - Pack of 100 Black
$7.99 -
M2 x 6mm Phillips Wafer Head Screw for Audiophile Headphone Headband Repair - Pack of 50 Black
$4.99
-
ASUS ROG Strix G15 G513R Replacement Screws Sold Individually – M1.6 x 3mm, M2 x 2.5mm, M2 x 3mm, M2.5 x 6mm Phillips Wafer Head, Black
$0.10Choose size -
ASUS ROG Strix G17 G713 Replacement Screws Sold Individually – M1.6 x 3mm, M2 x 2.5mm, M2 x 3mm, M2.5 x 6mm Phillips Wafer Head, Black
$0.10Choose size
More in Laptops & PCs
The same screw also fits
Devices whose records share a thread with ASUS S62, closest length match first.
- Lenovo Yoga S940-14IWL also M2 × 3 mm
- Lenovo G700 also M2 × 3 mm
- Dell G3 15 3579 also M2 × 3 mm
- Dell Inspiron 1318 also M2 × 3 mm
- Lenovo ThinkPad Yoga 460 also M2 × 3 mm
- Lenovo ThinkPad E570 also M2 × 3 mm
- Lenovo Yoga 370 also M2 × 3 mm
- Lenovo ThinkPad E14 Gen 8 also M2.5 × 6 mm
Questions about ASUS S62 screws
- What size screw does ASUS S62 use?
- M2 × 3 mm for bracket (qty 1, black); M2 × 3 mm for display (qty 4, black); M2 × 3 mm for memory (qty 4, black); M2 × 3 mm for palm rest (qty 1, black); M2 × 3 mm for system board (qty 2, black); M2 × 3 mm for unspecified (qty 4, black); M2 × 4 mm for display (qty 1, white,black); M2 × 6 mm for hinge (qty 2); M2 × 6 mm for unspecified (qty 2); M2.5 × 3 mm for display (qty 2, black); M2.5 × 4 mm for base cover (qty 1, black); M2.5 × 4 mm for display (qty 5, black); M2.5 × 4 mm for hard drive (qty 3, black); M2.5 × 4 mm for memory (qty 2, black); M2.5 × 4 mm for optical drive (qty 1, black); M2.5 × 4 mm for palm rest (qty 5, black); M2.5 × 4 mm for system board (qty 2, black); M2.5 × 4 mm for .
- How long are the screws in ASUS S62?
- The records range from 3 to 6 mm depending on the position, so match each screw to its own hole.
- What is the thread pitch of an M2 screw?
- 0.4 mm (coarse), which is the standard pitch for M2 machine screws; a 0.25 mm fine pitch exists but is uncommon. The tap drill is 1.6 mm and the normal clearance hole is 2.4 mm.
- What screwdriver do I need for ASUS S62?
- The sources do not name the drive. For M2, Phillips heads normally take PH0 and Torx heads T6; socket heads take a 1.5 mm hex key.
- Can I use an imperial screw instead of M2?
- No. Imperial look-alike: #2-56 UNC (2.18 mm) is close but not interchangeable. Use a true M2 screw so it does not cross-thread or strip the hole.
- Where can I buy replacement screws for ASUS S62?
- TechSpareWarehouse (our own store) lists M2 x 3mm, M2 x 4mm and M2 x 6mm, which match lengths in the records above.