Berkel 330M Slicer base/transmission fastener (short) screw size
M4 · 6 mm long
The screws used on Berkel 330M Slicer base/transmission fastener (short) are M4, 6 mm long.
The record covers stainless steel screw, Model 330M parts catalog.
This entry is marked confirmed and comes from berkelequipment.com.
An M4 screw is 4 mm in diameter with a 0.7 mm pitch, tapped with a 3.3 mm drill; imperial look-alike: #8-32 (4.17 mm) — the standard US PC/rack screw, close but not the same.
Berkel 330M Slicer base/transmission fastener (short) screw specifications
One row per fitment record. Head, drive are shown only where the source states them; pitch is the ISO coarse pitch for the thread.
| Thread | Length | Pitch | Head | Drive | Where it goes | Status |
|---|---|---|---|---|---|---|
| M4 | 6 mm | 0.7 mm | not stated | not stated | Stainless steel screw, Model 330M parts catalogstainless | Confirmed |
Fitment records and sources
Stainless steel screw, Model 330M parts catalog
pitch 0.7 mm · tap 3.3 mm · clearance 4.5 mm · PH2 / Torx T20
How to check the screw before you buy
- Vibration loosens small screws on drones and RC models, so builders commonly add a drop of medium (blue) threadlocker on metal-to-metal joints — never on plastic.
- Diameter: across the threads an M4 screw measures about 4 mm with calipers (usually a hair under). If yours measures noticeably more or less, it is a different thread.
- Pitch: 0.7 mm from one thread crest to the next (14.29 crests per centimetre). A thread pitch gauge or the pitch-gauge tool settles it in seconds.
- Length: measure from under the head to the tip for pan, button, wafer and cap heads; countersunk (flat) heads are measured overall.
- The record states 6 mm. Going longer risks bottoming out or touching parts behind the hole; going shorter loses thread engagement.
- Driver: the source does not name the drive. Standard M4 heads take PH2 for Phillips and T20 for Torx, and a 3 mm hex key for socket heads; a bit that fits loosely will cam out and strip the head.
- Tightening: no device-specific torque is published in these records. The site's general figure for M4 is about 2.0-3.0 N·m into metal threads and 0.8-1.4 N·m into plastic bosses; snug it up and stop.
Common mix-ups with M4
- Camera rig/cage accessories (SmallRig, Wooden Camera/Metabones) frequently mix M4 structural screws with 1/4-20 and 3/8-16 imperial mounting points on the same product — verify which specific fastener a manual is referencing before ordering replacements.
- M4 and 6-32 UNC share a nominal diameter with different pitch — a classic cross-thread in US-market kits.
More in Drones, RC & Gimbals
1/10 scale RC cars1/8 scale RC car chassis hardware3D-printed FPV stack mounts and spacers5-inch brushless motor to armAirsoft V2 / EHPA gearbox shellsALware Quad Flyer Spider 500 quadcopter kitAntique wall clock pendulum bracketsArcade marquee retainersARRMA Senton (and similar 1/10 vehicles)ARRMA Senton/kingpin-equipped vehiclesAxial Racing crawler/buggy kitsAxial SCX10 III RC crawler chassis
Browse all 144 in Drones, RC & Gimbals →The same screw also fits
Devices whose records share a thread with Berkel 330M Slicer base/transmission fastener (short), closest length match first.
- Meccano boxed sets (modern metric era) and compatible parts also M4 × 6 mm
- Singer / Bernette / EverSewn / Necchi sewing machines also M4 × 6 mm
- Singer/Bernette/EverSewn/Necchi home sewing machine needle plate also M4 × 6 mm
- Padlock and safe internals also M4 × 6 mm
- goBILDA metric building system also M4 × 6 mm
- HP LaserJet family common hardware also M4 × 6 mm
- Typewriter carriage brackets also M4 × 6 mm
- Schneider Electric Box iPC Universal / Performance also M4 × 6 mm
Questions about Berkel 330M Slicer base/transmission fastener (short) screws
- What size screw does Berkel 330M Slicer base/transmission fastener (short) use?
- M4 × 6 mm for stainless steel screw, Model 330M parts catalog.
- How long are the screws in Berkel 330M Slicer base/transmission fastener (short)?
- The record gives 6 mm. Measure the original from under the head (overall for a countersunk head) to confirm before ordering.
- What is the thread pitch of an M4 screw?
- 0.7 mm (coarse), which is the standard pitch for M4 machine screws; a 0.5 mm fine pitch exists but is uncommon. The tap drill is 3.3 mm and the normal clearance hole is 4.5 mm.
- What screwdriver do I need for Berkel 330M Slicer base/transmission fastener (short)?
- The sources do not name the drive. For M4, Phillips heads normally take PH2 and Torx heads T20; socket heads take a 3 mm hex key.
- Can I use an imperial screw instead of M4?
- No. Imperial look-alike: #8-32 (4.17 mm) — the standard US PC/rack screw, close but not the same. Use a true M4 screw so it does not cross-thread or strip the hole.