Burris Fast Fire 3 optic mounting screw screw size
M3 · 7 mm long
Burris Fast Fire 3 optic mounting screw takes M3 metric screws, 7 mm long.
It is listed for M3 x 0.5 x 7mm.
This entry is marked confirmed and comes from battlewerx.com.
An M3 screw is 3 mm in diameter with a 0.5 mm pitch, tapped with a 2.5 mm drill; imperial look-alike: #5-40 (3.18 mm) or #4-40 — neither interchanges with M3.
Burris Fast Fire 3 optic mounting screw screw specifications
One row per fitment record. Head, drive are shown only where the source states them; pitch is the ISO coarse pitch for the thread.
| Thread | Length | Pitch | Head | Drive | Where it goes | Status |
|---|---|---|---|---|---|---|
| M3 | 7 mm | 0.5 mm | not stated | not stated | M3 x 0.5 x 7mm | Confirmed |
Fitment records and sources
How to check the screw before you buy
- Do not confuse metric mounting screws with the 1/4-20 or 3/8-16 tripod threads that cameras and clamps also carry.
- Diameter: across the threads an M3 screw measures about 3 mm with calipers (usually a hair under). If yours measures noticeably more or less, it is a different thread.
- Pitch: 0.5 mm from one thread crest to the next (20 crests per centimetre). A thread pitch gauge or the pitch-gauge tool settles it in seconds.
- Length: measure from under the head to the tip for pan, button, wafer and cap heads; countersunk (flat) heads are measured overall.
- The record states 7 mm. Going longer risks bottoming out or touching parts behind the hole; going shorter loses thread engagement.
- Driver: the source does not name the drive. Standard M3 heads take PH1 for Phillips and T10 for Torx, and a 2.5 mm hex key for socket heads; a bit that fits loosely will cam out and strip the head.
- Tightening: no device-specific torque is published in these records. The site's general figure for M3 is about 80-130 N·cm into metal threads and 35-60 N·cm into plastic bosses; snug it up and stop.
Common mix-ups with M3
- M3 (3.0mm, 0.5mm pitch) is not #6-32 UNC (~3.5mm) — they look identical and cross-thread, the single most common PC-building mistake.
More in Cameras & Optics
1.25" eyepiece/diagonal/SCT visual back thumb screwAimpoint Comp M4 / M4s LRP & TNP mountAimpoint Micro T-1/T-2/H-1/H-2 standard mountAimpoint Micro T-1/T-2/H-1/H-2 standard mount screwAimpoint SM-2001/2007 Micro T1/T2 mountAirsoft red dot sight mounting screw set (Laylax/Quintes Sence)Airsoft/firearm red-dot sight optic mounting screws (Vortex Viper, Swampfox patterns)Alpine and touring ski bindings (Binding Freedom inserts)Arca-style quick-release plateARRI plate for Sony VENICE 1/2Artesky 340mm Vixen Dovetail BarAstromania finder scope dovetail base
Browse all 278 in Cameras & Optics →The same screw also fits
Devices whose records share a thread with Burris Fast Fire 3 optic mounting screw, closest length match first.
- Vintage camera / electronics faceplates also M3 × 7 mm
- Refrigerator light cover and shelf clips also M3 × 7 mm
- Microscope objective turret and stage also M3 × 7 mm
- Wimberley AP-640 replacement lens foot also M3 × 7 mm
- Olympus BH-2 microscope frame also M3 × 7 mm
- Telescope thumb screws for diagonals, adapters and focusers also M3 × 7 mm
- Camera cage shells (SmallRig-style) also M3 × 7 mm
- Meade LX200 Barlow / eyepiece retaining screw also M3 × 7 mm
Questions about Burris Fast Fire 3 optic mounting screw screws
- What size screw does Burris Fast Fire 3 optic mounting screw use?
- M3 × 7 mm for M3 x 0.5 x 7mm.
- How long are the screws in Burris Fast Fire 3 optic mounting screw?
- The record gives 7 mm. Measure the original from under the head (overall for a countersunk head) to confirm before ordering.
- What is the thread pitch of an M3 screw?
- 0.5 mm (coarse), which is the standard pitch for M3 machine screws; a 0.35 mm fine pitch exists but is uncommon. The tap drill is 2.5 mm and the normal clearance hole is 3.4 mm.
- What screwdriver do I need for Burris Fast Fire 3 optic mounting screw?
- The sources do not name the drive. For M3, Phillips heads normally take PH1 and Torx heads T10; socket heads take a 2.5 mm hex key.
- Can I use an imperial screw instead of M3?
- No. Imperial look-alike: #5-40 (3.18 mm) or #4-40 — neither interchanges with M3. Use a true M3 screw so it does not cross-thread or strip the hole.