Camera lens mount flange screw size
M2.5 · 3 to 6 mm long
Camera lens mount flange takes M2.5 metric screws in lengths from 3 to 6 mm.
It is listed for secures the lens mount to a mirrorless or DSLR body.
This entry is marked reported and comes from alibaba.com.
For reference, M2.5 is 2.5 mm across the threads at 0.45 mm pitch. The imperial size people confuse it with: #3-48 / #4-40 (2.51 / 2.84 mm) — #4-40 is the common US stand-in and it will NOT thread in.
Camera lens mount flange screw specifications
One row per fitment record. Head, drive are shown only where the source states them; pitch is the ISO coarse pitch for the thread.
| Thread | Length | Pitch | Head | Drive | Where it goes | Status |
|---|---|---|---|---|---|---|
| M2.5 | 3–6 mm | 0.45 mm | not stated | not stated | secures the lens mount to a mirrorless or DSLR body | Reported |
Fitment records and sources
secures the lens mount to a mirrorless or DSLR body
pitch 0.45 mm · tap 2.05 mm · clearance 2.9 mm · PH1 / Torx T8
How to check the screw before you buy
- Do not confuse metric mounting screws with the 1/4-20 or 3/8-16 tripod threads that cameras and clamps also carry.
- Diameter: across the threads an M2.5 screw measures about 2.5 mm with calipers (usually a hair under). If yours measures noticeably more or less, it is a different thread.
- Pitch: 0.45 mm from one thread crest to the next (22.22 crests per centimetre). A thread pitch gauge or the pitch-gauge tool settles it in seconds.
- Length: measure from under the head to the tip for pan, button, wafer and cap heads; countersunk (flat) heads are measured overall.
- The records span 3–6 mm, which means different positions take different lengths — match each hole to its own screw.
- Driver: the source does not name the drive. Standard M2.5 heads take PH1 for Phillips and T8 for Torx, and a 2 mm hex key for socket heads; a bit that fits loosely will cam out and strip the head.
- Tightening: no device-specific torque is published in these records. The site's general figure for M2.5 is about 45-70 N·cm into metal threads and 20-35 N·cm into plastic bosses; snug it up and stop.
Common mix-ups with M2.5
- Projector optics and fan screws often step down to M2.5 while the outer covers use M3 - do not reuse cover screws inside the light engine.
- M2.5 pitch is 0.45mm vs M3's 0.5mm and M2's 0.4mm — forcing the wrong one strips plastic bosses instantly.
Buy these screws at TechSpare Warehouse
In stock and shipped from South Carolina. Our black screws are Phillips wafer head (low profile); match the head style and length to the original before you order.
-
25x M2.5 x 3mm Phillips Screws for Acer Nitro 5 SSD M.2 WiFi Card
$5.99 -
M2.5 x 4mm Screws for Lenovo IdeaPad 5 Pro 14 Display Hinge 10-Pack Black
$4.99 -
M2.5 x 4mm Screws for Lenovo IdeaPad 5 Pro 14 System Board Hinge 10-Pack Black
$4.99
-
M2.5 x 5mm Screws Compatible with Dell XPS 14 9440 Display Assembly 10-Pack
$4.99 -
M2.5 x 5mm Phillips Wafer Head Screw for Action Camera Protective Housing - Pack of 50 Black
$4.79 each · min. 2
-
Dell Inspiron 15 3520 Replacement Screws Sold Individually – M2 x 3mm, M2 x 5mm, M2.5 x 5mm, M3 x 3mm Phillips Wafer Head, Black
$0.10Choose size -
Dell Latitude 5430 Replacement Screws Sold Individually – M2 x 2.5mm, M2 x 3mm, M2 x 5mm, M2.5 x 5mm Phillips Wafer Head, Black
$0.10Choose size
-
ASUS ROG Strix G15 G513R Replacement Screws Sold Individually – M1.6 x 3mm, M2 x 2.5mm, M2 x 3mm, M2.5 x 6mm Phillips Wafer Head, Black
$0.10Choose size
More in Cameras & Optics
1.25" eyepiece/diagonal/SCT visual back thumb screwAimpoint Comp M4 / M4s LRP & TNP mountAimpoint Micro T-1/T-2/H-1/H-2 standard mountAimpoint Micro T-1/T-2/H-1/H-2 standard mount screwAimpoint SM-2001/2007 Micro T1/T2 mountAirsoft red dot sight mounting screw set (Laylax/Quintes Sence)Airsoft/firearm red-dot sight optic mounting screws (Vortex Viper, Swampfox patterns)Alpine and touring ski bindings (Binding Freedom inserts)Arca-style quick-release plateARRI plate for Sony VENICE 1/2Artesky 340mm Vixen Dovetail BarAstromania finder scope dovetail base
Browse all 278 in Cameras & Optics →The same screw also fits
Devices whose records share a thread with Camera lens mount flange, closest length match first.
- Camera hot shoe base plate also M2.5 × 3–5 mm
- Raspberry Pi camera module mounts also M2.5 × 4–6 mm
- Microscope objective turret also M2.5 × 4–6 mm
- Camera cages & rigs also M2.5 × 4–6 mm
- Kurokesu QR-PLATE-20 Arca-Swiss plate also M2.5 × 5 mm
- Lenovo ThinkPad T520i also M2.5 × 6 mm
- Lenovo ThinkPad X1 Carbon Gen 12 / X1 2-in-1 Gen 9 also M2.5 × 4 mm
- GE HealthCare anesthesia delivery machine also M2.5 × 6 mm
Questions about Camera lens mount flange screws
- What size screw does Camera lens mount flange use?
- M2.5 × 3–6 mm for secures the lens mount to a mirrorless or DSLR body.
- How long are the screws in Camera lens mount flange?
- The records range from 3 to 6 mm depending on the position, so match each screw to its own hole.
- What is the thread pitch of an M2.5 screw?
- 0.45 mm (coarse), which is the standard pitch for M2.5 machine screws; a 0.35 mm fine pitch exists but is uncommon. The tap drill is 2.05 mm and the normal clearance hole is 2.9 mm.
- What screwdriver do I need for Camera lens mount flange?
- The sources do not name the drive. For M2.5, Phillips heads normally take PH1 and Torx heads T8; socket heads take a 2 mm hex key.
- Can I use an imperial screw instead of M2.5?
- No. Imperial look-alike: #3-48 / #4-40 (2.51 / 2.84 mm) — #4-40 is the common US stand-in and it will NOT thread in. Use a true M2.5 screw so it does not cross-thread or strip the hole.
- Where can I buy replacement screws for Camera lens mount flange?
- TechSpareWarehouse (our own store) lists M2.5 x 3mm, M2.5 x 4mm and M2.5 x 5mm, which match lengths in the records above.