Celestron EdgeHD 11" OTA secondary mirror collimation screws screw size
M3 · 12 mm long
Celestron EdgeHD 11" OTA secondary mirror collimation screws takes M3 metric screws, 12 mm long.
It is listed for official Celestron reference lists M3 x 0.5, 12mm collimation screws for the 11" EdgeHD tube.
This entry is marked confirmed and comes from celestron.com.
For reference, M3 is 3 mm across the threads at 0.5 mm pitch. The imperial size people confuse it with: #5-40 (3.18 mm) or #4-40 — neither interchanges with M3.
Celestron EdgeHD 11" OTA secondary mirror collimation screws screw specifications
One row per fitment record. Head, drive are shown only where the source states them; pitch is the ISO coarse pitch for the thread.
| Thread | Length | Pitch | Head | Drive | Where it goes | Status |
|---|---|---|---|---|---|---|
| M3 | 12 mm | 0.5 mm | not stated | not stated | Official Celestron reference lists M3 x 0.5, 12mm collimation screws for the 11" EdgeHD tube | Confirmed |
Fitment records and sources
Official Celestron reference lists M3 x 0.5, 12mm collimation screws for the 11" EdgeHD tube.
pitch 0.5 mm · tap 2.5 mm · clearance 3.4 mm · PH1 / Torx T10
How to check the screw before you buy
- Do not confuse metric mounting screws with the 1/4-20 or 3/8-16 tripod threads that cameras and clamps also carry.
- Diameter: across the threads an M3 screw measures about 3 mm with calipers (usually a hair under). If yours measures noticeably more or less, it is a different thread.
- Pitch: 0.5 mm from one thread crest to the next (20 crests per centimetre). A thread pitch gauge or the pitch-gauge tool settles it in seconds.
- Length: measure from under the head to the tip for pan, button, wafer and cap heads; countersunk (flat) heads are measured overall.
- The record states 12 mm. Going longer risks bottoming out or touching parts behind the hole; going shorter loses thread engagement.
- Driver: the source does not name the drive. Standard M3 heads take PH1 for Phillips and T10 for Torx, and a 2.5 mm hex key for socket heads; a bit that fits loosely will cam out and strip the head.
- Tightening: no device-specific torque is published in these records. The site's general figure for M3 is about 80-130 N·cm into metal threads and 35-60 N·cm into plastic bosses; snug it up and stop.
Common mix-ups with M3
- Telescope thumbscrews are sold in a wide non-metric legacy range too (1/4-20, 8-32, 10-32 on many Meade/Celestron mounts), so metric M3/M4 fitment applies mainly to newer/international accessory ecosystems (SkyWatcher, generic 1.25" accessories) and should not be assumed universal.
- The bioprinter M3 reference is a tube-connector thread spec, not a structural chassis screw; verify before assuming interchangeability with fastener screws.
Buy these screws at TechSpare Warehouse
In stock and shipped from South Carolina. Our black screws are Phillips wafer head (low profile); match the head style and length to the original before you order.
-
M3 x 12mm Phillips Wafer Head Screw for Camera Cage & Battery Slide Mount - Pack of 50 Black
$6.49 -
M3 x 12mm Phillips Wafer Head Screw for Electric Scooter LCD Dashboard - Single Replacement Black
$0.10 each · min. 50
-
M3 x 12mm Phillips Wafer Head Screw for RC Car/Truck Chassis Mount - Single Replacement Black
$0.10 each · min. 50
More in Cameras & Optics
1.25" eyepiece/diagonal/SCT visual back thumb screwAimpoint Comp M4 / M4s LRP & TNP mountAimpoint Micro T-1/T-2/H-1/H-2 standard mountAimpoint Micro T-1/T-2/H-1/H-2 standard mount screwAimpoint SM-2001/2007 Micro T1/T2 mountAirsoft red dot sight mounting screw set (Laylax/Quintes Sence)Airsoft/firearm red-dot sight optic mounting screws (Vortex Viper, Swampfox patterns)Alpine and touring ski bindings (Binding Freedom inserts)Arca-style quick-release plateARRI plate for Sony VENICE 1/2Artesky 340mm Vixen Dovetail BarAstromania finder scope dovetail base
Browse all 278 in Cameras & Optics →The same screw also fits
Devices whose records share a thread with Celestron EdgeHD 11" OTA secondary mirror collimation screws, closest length match first.
- Celestron EdgeHD 8" OTA secondary mirror collimation screws also M3 × 12 mm
- Wooden Camera 153250 SSD Guard (RED EPIC) also M3 × 12 mm
- Telescope accessory thumb screws also M3 × 12 mm
- OpenFlexure Delta Stage also M3 × 12 mm
- Partizan / Pilotix PT10 V3 FPV frame also M3 × 12 mm
- Microscope objective turret and stage also M3 × 12 mm
- Wimberley AP-553 lens foot plate also M3 × 12 mm
- Celestron C11 Schmidt-Cassegrain OTA secondary mirror collimation screws also M3 × 12 mm
Questions about Celestron EdgeHD 11" OTA secondary mirror collimation screws screws
- What size screw does Celestron EdgeHD 11" OTA secondary mirror collimation screws use?
- M3 × 12 mm for official Celestron reference lists M3 x 0.5, 12mm collimation screws for the 11" EdgeHD tube.
- How long are the screws in Celestron EdgeHD 11" OTA secondary mirror collimation screws?
- The record gives 12 mm. Measure the original from under the head (overall for a countersunk head) to confirm before ordering.
- What is the thread pitch of an M3 screw?
- 0.5 mm (coarse), which is the standard pitch for M3 machine screws; a 0.35 mm fine pitch exists but is uncommon. The tap drill is 2.5 mm and the normal clearance hole is 3.4 mm.
- What screwdriver do I need for Celestron EdgeHD 11" OTA secondary mirror collimation screws?
- The sources do not name the drive. For M3, Phillips heads normally take PH1 and Torx heads T10; socket heads take a 2.5 mm hex key.
- Can I use an imperial screw instead of M3?
- No. Imperial look-alike: #5-40 (3.18 mm) or #4-40 — neither interchanges with M3. Use a true M3 screw so it does not cross-thread or strip the hole.
- Where can I buy replacement screws for Celestron EdgeHD 11" OTA secondary mirror collimation screws?
- TechSpareWarehouse (our own store) lists M3 x 12mm, which matches the length in the records above.