Dell Inspiron 13 7375 2-in-1 screw size

Dell Inspiron 13 7375 2-in-1 screw specifications

One row per fitment record. Head, drive are shown only where the source states them; pitch is the ISO coarse pitch for the thread.

How to check the screw before you buy

1. Laptop covers and brackets often mix two or three lengths of the same thread, so lay the screws out in the order they came out (a magnetic mat or a sheet of paper with the hole pattern drawn on it works).
2. Diameter: across the threads an M1.2 screw measures about 1.2 mm with calipers (usually a hair under). This device also uses M2 / M2.5, so measure each screw rather than assuming they match.
3. Pitch: 0.25 mm from one thread crest to the next (40 crests per centimetre). A thread pitch gauge or the pitch-gauge tool settles it in seconds.
4. Length: measure from under the head to the tip for pan, button, wafer and cap heads; countersunk (flat) heads are measured overall.
5. The records span 1.4–7 mm, which means different positions take different lengths — match each hole to its own screw.
6. Driver: the source does not name the drive. Standard M1.2 heads take PH000 / JIS 00 for Phillips and T1–T2 for Torx; a bit that fits loosely will cam out and strip the head.
7. Tightening: no device-specific torque is published in these records. The site's general figure for M1.2 is about 5-8 N·cm into metal threads and 3-5 N·cm into plastic bosses; snug it up and stop.

Pitch gauge · Screw size finder · Torque guide

More in Laptops & PCs

The same screw also fits

Devices whose records share a thread with Dell Inspiron 13 7375 2-in-1, closest length match first.

• HP 2000 also M2 × 3 mm
• Dell Precision 5770 also M2 × 2 mm
• Dell Inspiron 14 3467 also M2 × 2 mm
• Dell Precision 7670 also M2 × 2 mm
• Lenovo 15IRX10 also M2 × 3 mm
• HP Compaq Evo N610c also M2.5 × 2.5 mm
• MSI Prestige 14 AI+ (MS-14N3) also M2 × 2 mm
• Dell Vostro 15 3510 also M2 × 2 mm

Questions about Dell Inspiron 13 7375 2-in-1 screws

What size screw does Dell Inspiron 13 7375 2-in-1 use?

M1.2 × 1.4 mm for keyboard (qty 14); M2 × 2 mm for bracket (qty 4); M2 × 2 mm for keyboard (qty 14, broadhead); M2 × 2 mm for system board (qty 3, broadhead); M2 × 2 mm for touchpad (qty 4); M2 × 3 mm for battery (qty 4); M2 × 3 mm for DC-in (qty 1); M2 × 3 mm for fan (qty 2); M2 × 3 mm for SSD (qty 1); M2 × 3 mm for unspecified (qty 1); M2 × 3 mm for wireless card (qty 1); M2 × 3.5 mm for I/O board (qty 2); M2.5 × 2.5 mm for display (qty 4, broadhead); M2.5 × 2.5 mm for unspecified (qty 1); M2.5 × 5 mm for bracket (qty 2, broadhead); M2.5 × 5 mm for system board (qty 2); M2.5 × 7 mm for base cover (qty 9).

How long are the screws in Dell Inspiron 13 7375 2-in-1?

The records range from 1.4 to 7 mm depending on the position, so match each screw to its own hole.

What is the thread pitch of an M1.2 screw?

0.25 mm (coarse), which is the standard pitch for M1.2 machine screws. The tap drill is 0.95 mm and the normal clearance hole is 1.4 mm.

What screwdriver do I need for Dell Inspiron 13 7375 2-in-1?

The sources do not name the drive. For M1.2, Phillips heads normally take PH000 / JIS 00 and Torx heads T1–T2.

Can I use an imperial screw instead of M1.2?

No. Imperial look-alike: #0-80 UNF (1.52 mm) is the closest imperial screw, but it is bigger — not a substitute. Use a true M1.2 screw so it does not cross-thread or strip the hole.

Where can I buy replacement screws for Dell Inspiron 13 7375 2-in-1?

TechSpareWarehouse (our own store) lists M2 x 2mm, M2 x 3mm and M2.5 x 5mm, which match lengths in the records above.