Dell Inspiron 15 7567 screw size

Dell Inspiron 15 7567 screw specifications

One row per fitment record. Head, drive are shown only where the source states them; pitch is the ISO coarse pitch for the thread.

How to check the screw before you buy

1. Laptop covers and brackets often mix two or three lengths of the same thread, so lay the screws out in the order they came out (a magnetic mat or a sheet of paper with the hole pattern drawn on it works).
2. Diameter: across the threads an M2 screw measures about 2 mm with calipers (usually a hair under). This device also uses M2.5 / M3, so measure each screw rather than assuming they match.
3. Pitch: 0.4 mm from one thread crest to the next (25 crests per centimetre). A thread pitch gauge or the pitch-gauge tool settles it in seconds.
4. Length: measure from under the head to the tip for pan, button, wafer and cap heads; countersunk (flat) heads are measured overall.
5. The records span 2–8 mm, which means different positions take different lengths — match each hole to its own screw.
6. Driver: the source names a Torx T8 drive. For comparison, standard M2 heads take PH0 (Phillips) or T6 (Torx), or a 1.5 mm hex key.
7. Tightening: no device-specific torque is published in these records. The site's general figure for M2 is about 25-40 N·cm into metal threads and 12-20 N·cm into plastic bosses; snug it up and stop.

Pitch gauge · Screw size finder · Torque guide

More in Laptops & PCs

The same screw also fits

Devices whose records share a thread with Dell Inspiron 15 7567, closest length match first.

• Dell Inspiron 15 7577 also M2 × 2 mm
• HP 250 G9 also M2 × 2.5 mm
• Dell Latitude D600 also M2 × 3 mm
• Lenovo ThinkPad P14s Gen 3 also M2 × 2.5 mm
• HP Victus by HP 16.1 inch Gaming 16-d0000 also M2 × 2 mm
• Lenovo ideapad 320SX-14IKB also M2 × 3 mm
• Lenovo ThinkPad E50 also M2 × 2 mm
• Lenovo B50-80 also M2 × 2 mm

Questions about Dell Inspiron 15 7567 screws

What size screw does Dell Inspiron 15 7567 use?

M2 × 2 mm for touchpad (qty 4); M2 × 2.5 mm for display (qty 4); M2 × 2.5 mm for power button (qty 2); M2 × 3 mm for I/O board (qty 2); M2 × 3 mm for LED board (qty 2); M2 × 3 mm for DC-in (qty 4); M2 × 3 mm for display (qty 2); M2 × 3 mm for display back cover (qty 4, broadhead); M2 × 3 mm for fan (qty 6); M2 × 3 mm for heat sink (qty 6); M2 × 3 mm for speaker (qty 6, broadhead); M2 × 3 mm for SSD (qty 1); M2 × 3 mm for system board (qty 2); M2 × 3 mm for wireless card (qty 1); M2 × 4 mm for battery (qty 5, Torx T8); M2.5 × 2.5 mm for hinge (qty 8); M2.5 × 3 mm for hard drive (qty 4); M2.5 × 5 mm for display (qty 2); M2.5 × 5 mm for palm rest (qty 15); M2.5 × 8 mm for palm rest (qty 2); M3 .

How long are the screws in Dell Inspiron 15 7567?

The records range from 2 to 8 mm depending on the position, so match each screw to its own hole.

What is the thread pitch of an M2 screw?

0.4 mm (coarse), which is the standard pitch for M2 machine screws; a 0.25 mm fine pitch exists but is uncommon. The tap drill is 1.6 mm and the normal clearance hole is 2.4 mm.

What screwdriver do I need for Dell Inspiron 15 7567?

The source lists a Torx T8 drive. Standard M2 heads otherwise take PH0 (Phillips) or T6 (Torx), or a 1.5 mm hex key.

Can I use an imperial screw instead of M2?

No. Imperial look-alike: #2-56 UNC (2.18 mm) is close but not interchangeable. Use a true M2 screw so it does not cross-thread or strip the hole.

Where can I buy replacement screws for Dell Inspiron 15 7567?

TechSpareWarehouse (our own store) lists M2 x 2mm, M2 x 2.5mm and M2 x 3mm, which match lengths in the records above.