Dell Latitude 5290 screw size

Dell Latitude 5290 screw specifications

One row per fitment record. Head, drive are shown only where the source states them; pitch is the ISO coarse pitch for the thread.

How to check the screw before you buy

1. Laptop covers and brackets often mix two or three lengths of the same thread, so lay the screws out in the order they came out (a magnetic mat or a sheet of paper with the hole pattern drawn on it works).
2. Diameter: across the threads an M1.6 screw measures about 1.6 mm with calipers (usually a hair under). This device also uses M2 / M2.5 / M3, so measure each screw rather than assuming they match.
3. Pitch: 0.35 mm from one thread crest to the next (28.57 crests per centimetre). A thread pitch gauge or the pitch-gauge tool settles it in seconds.
4. Length: measure from under the head to the tip for pan, button, wafer and cap heads; countersunk (flat) heads are measured overall.
5. The records span 1.1–6.3 mm, which means different positions take different lengths — match each hole to its own screw.
6. Driver: the source does not name the drive. Standard M1.6 heads take PH00 for Phillips and T4–T5 for Torx, and a 1.5 mm hex key for socket heads; a bit that fits loosely will cam out and strip the head.
7. Tightening: no device-specific torque is published in these records. The site's general figure for M1.6 is about 12-20 N·cm into metal threads and 6-10 N·cm into plastic bosses; snug it up and stop.

Pitch gauge · Screw size finder · Torque guide

More in Laptops & PCs

The same screw also fits

Devices whose records share a thread with Dell Latitude 5290, closest length match first.

• HP Chromebook Enterprise x360 14E G1 also M2 × 2.5 mm
• LG LS50 also M2 × 2.5 mm
• HP Compaq 6720T also M2 × 2 mm
• Lenovo ThinkPad X1 Carbon (Type 34xx) also M2 × 2 mm
• Lenovo E4325 also M2 × 2.5 mm
• HP Pavilion ZE2000 also M2 × 3 mm
• HP EliteBook 830 G7 also M1.6 × 3 mm
• Dell Latitude 5340 also M2 × 2 mm

Questions about Dell Latitude 5290 screws

What size screw does Dell Latitude 5290 use?

M1.6 × 3 mm for camera (qty 2); M1.6 × 3 mm for display (qty 6); M1.6 × 3 mm for unspecified (qty 4); M1.6 × 3 mm for wireless card (qty 1); M2 × 1.1 mm for unspecified (qty 3); M2 × 2 mm for bracket (qty 2); M2 × 2 mm for chassis/frame (qty 2); M2 × 2 mm for display (qty 2); M2 × 2 mm for keyboard (qty 5); M2 × 2 mm for palm rest (qty 2); M2 × 2.5 mm for card reader (qty 3); M2 × 2.5 mm for heat sink (qty 4); M2 × 2.5 mm for SSD (qty 1); M2 × 2.5 mm for system board (qty 4); M2 × 2.5 mm for touchpad (qty 2); M2 × 3 mm for LED board (qty 1); M2 × 3 mm for card reader (qty 2); M2 × 3 mm for chassis/frame (qty 2); M2 × 3 mm for heat sink (qty 6); M2 × 3 mm for palm rest (qty 2); M2 × 3 mm for .

How long are the screws in Dell Latitude 5290?

The records range from 1.1 to 6.3 mm depending on the position, so match each screw to its own hole.

What is the thread pitch of an M1.6 screw?

0.35 mm (coarse), which is the standard pitch for M1.6 machine screws; a 0.2 mm fine pitch exists but is uncommon. The tap drill is 1.25 mm and the normal clearance hole is 1.8 mm.

What screwdriver do I need for Dell Latitude 5290?

The sources do not name the drive. For M1.6, Phillips heads normally take PH00 and Torx heads T4–T5; socket heads take a 1.5 mm hex key.

Can I use an imperial screw instead of M1.6?

No. Imperial look-alike: #1-72 UNF (1.85 mm) is larger; there is no true imperial equivalent. Use a true M1.6 screw so it does not cross-thread or strip the hole.

Where can I buy replacement screws for Dell Latitude 5290?

TechSpareWarehouse (our own store) lists M1.6 x 3mm, M2 x 2mm and M2 x 2.5mm, which match lengths in the records above.