Dell Latitude 5430 Rugged screw size

Dell Latitude 5430 Rugged screw specifications

One row per fitment record. Head, drive are shown only where the source states them; pitch is the ISO coarse pitch for the thread.

How to check the screw before you buy

1. A screw that is even 1 mm too long in a laptop base can push into the keyboard, battery or a board trace, so match the length position by position.
2. Diameter: across the threads an M2 screw measures about 2 mm with calipers (usually a hair under). This device also uses M2.5 / M3, so measure each screw rather than assuming they match.
3. Pitch: 0.4 mm from one thread crest to the next (25 crests per centimetre). A thread pitch gauge or the pitch-gauge tool settles it in seconds.
4. Length: measure from under the head to the tip for pan, button, wafer and cap heads; countersunk (flat) heads are measured overall.
5. The records span 2–7 mm, which means different positions take different lengths — match each hole to its own screw.
6. Driver: the source names a Torx T8 drive. For comparison, standard M2 heads take PH0 (Phillips) or T6 (Torx), or a 1.5 mm hex key.
7. Tightening: no device-specific torque is published in these records. The site's general figure for M2 is about 25-40 N·cm into metal threads and 12-20 N·cm into plastic bosses; snug it up and stop.

Pitch gauge · Screw size finder · Torque guide

More in Laptops & PCs

The same screw also fits

Devices whose records share a thread with Dell Latitude 5430 Rugged, closest length match first.

• Lenovo YOGA 730-15IWL also M2 × 2 mm
• Dell Latitude 14 5420 also M2 × 5 mm
• Lenovo ThinkPad R60e also M2 × 3.5 mm
• Dell Latitude 5488 also M2 × 2 mm
• HP Compaq Presario CQ42 also M2.5 × 4 mm
• Lenovo B50-10 also M2 × 2 mm
• Lenovo ThinkPad L330 also M2 × 3.5 mm
• HP Pavilion zx5000 also M2.5 × 4 mm

Questions about Dell Latitude 5430 Rugged screws

What size screw does Dell Latitude 5430 Rugged use?

M2 × 2 mm for SSD (qty 1); M2 × 3.5 mm for I/O board (qty 2); M2 × 3.5 mm for LED board (qty 2); M2 × 3.5 mm for heat sink (qty 3); M2 × 3.5 mm for keyboard (qty 4); M2 × 3.5 mm for power button (qty 3); M2 × 3.5 mm for speaker (qty 2); M2 × 3.5 mm for system board (qty 5); M2 × 3.5 mm for USB-C board (qty 5); M2 × 3.5 mm for wireless card (qty 1); M2 × 4 mm for base cover (qty 8); M2 × 4 mm for SSD (qty 1); M2 × 5 mm for SSD (qty 1); M2 × 6 mm for heat sink (qty 4, captive); M2.5 × 4 mm for keyboard (qty 6); M2.5 × 5 mm for I/O board (qty 2); M2.5 × 5 mm for display (qty 2); M2.5 × 5 mm for power button (qty 4); M2.5 × 5 mm for system board (qty 9); M2.5 × 5 mm for unspecified (qty 1); M2.5.

How long are the screws in Dell Latitude 5430 Rugged?

The records range from 2 to 7 mm depending on the position, so match each screw to its own hole.

What is the thread pitch of an M2 screw?

0.4 mm (coarse), which is the standard pitch for M2 machine screws; a 0.25 mm fine pitch exists but is uncommon. The tap drill is 1.6 mm and the normal clearance hole is 2.4 mm.

What screwdriver do I need for Dell Latitude 5430 Rugged?

The source lists a Torx T8 drive. Standard M2 heads otherwise take PH0 (Phillips) or T6 (Torx), or a 1.5 mm hex key.

Can I use an imperial screw instead of M2?

No. Imperial look-alike: #2-56 UNC (2.18 mm) is close but not interchangeable. Use a true M2 screw so it does not cross-thread or strip the hole.

Where can I buy replacement screws for Dell Latitude 5430 Rugged?

TechSpareWarehouse (our own store) lists M2 x 2mm, M2 x 4mm and M2 x 5mm, which match lengths in the records above.