Dell Latitude C500 screw size
M2 / M2.5 / M3 · 3 to 12 mm long
The screws used on Dell Latitude C500 are M2, M2.5 and M3 in lengths from 3 to 12 mm.
There are 18 separate fitment records for it, including base cover (qty 2) (M2), bracket (qty 2) (M2) and display (qty 2) (M2), plus 15 more in the table below.
Head and drive, as the sources state them: pan head.
18 of the 18 records are marked confirmed, drawn from 2 sources (tim.id.au and dl.dell.com).
For reference, M2 is 2 mm across the threads at 0.4 mm pitch. The imperial size people confuse it with: #2-56 UNC (2.18 mm) is close but not interchangeable.
Dell Latitude C500 screw specifications
One row per fitment record. Head, drive are shown only where the source states them; pitch is the ISO coarse pitch for the thread.
| Thread | Length | Pitch | Head | Drive | Where it goes | Status |
|---|---|---|---|---|---|---|
| M2 | 3 mm | 0.4 mm | not stated | not stated | Base cover (qty 2) | Confirmed |
| M2 | 3 mm | 0.4 mm | not stated | not stated | Bracket (qty 2) | Confirmed |
| M2 | 3 mm | 0.4 mm | not stated | not stated | Display (qty 2) | Confirmed |
| M2 | 3 mm | 0.4 mm | not stated | not stated | Heat sink (qty 2) | Confirmed |
| M2 | 3 mm | 0.4 mm | not stated | not stated | Palm rest (qty 3) | Confirmed |
| M2 | 3 mm | 0.4 mm | not stated | not stated | Unspecified (qty 2) | Confirmed |
| M2 | 4 mm | 0.4 mm | not stated | not stated | Display (qty 5) | Confirmed |
| M2.5 | 12 mm | 0.45 mm | not stated | not stated | Keyboard (qty 5) | Confirmed |
| M2.5 | 12 mm | 0.45 mm | not stated | not stated | Palm rest (qty 3) | Confirmed |
| M2.5 | 5 mm | 0.45 mm | not stated | not stated | Base cover (qty 9) | Confirmed |
| M2.5 | 5 mm | 0.45 mm | Pan head | not stated | Display (qty 6, pan) | Confirmed |
| M2.5 | 5 mm | 0.45 mm | not stated | not stated | Display bezel (qty 6) | Confirmed |
| M2.5 | 5 mm | 0.45 mm | not stated | not stated | Fan (qty 3) | Confirmed |
| M2.5 | 5 mm | 0.45 mm | not stated | not stated | Heat sink (qty 2) | Confirmed |
| M2.5 | 5 mm | 0.45 mm | not stated | not stated | Hinge (qty 5) | Confirmed |
| M2.5 | 5 mm | 0.45 mm | not stated | not stated | System board (qty 6, white) | Confirmed |
| M3 | 3 mm | 0.5 mm | not stated | not stated | Display (qty 4) | Confirmed |
| M3 | 5 mm | 0.5 mm | not stated | not stated | Hard drive (qty 1) | Confirmed |
Fitment records and sources
Base cover (qty 2)
pitch 0.4 mm · tap 1.6 mm · clearance 2.4 mm · PH0 / Torx T6
Bracket (qty 2)
pitch 0.4 mm · tap 1.6 mm · clearance 2.4 mm · PH0 / Torx T6
Display (qty 2)
pitch 0.4 mm · tap 1.6 mm · clearance 2.4 mm · PH0 / Torx T6
Heat sink (qty 2)
pitch 0.4 mm · tap 1.6 mm · clearance 2.4 mm · PH0 / Torx T6
Palm rest (qty 3)
pitch 0.4 mm · tap 1.6 mm · clearance 2.4 mm · PH0 / Torx T6
Unspecified (qty 2)
pitch 0.4 mm · tap 1.6 mm · clearance 2.4 mm · PH0 / Torx T6
Display (qty 5)
pitch 0.4 mm · tap 1.6 mm · clearance 2.4 mm · PH0 / Torx T6
Keyboard (qty 5)
pitch 0.45 mm · tap 2.05 mm · clearance 2.9 mm · PH1 / Torx T8
Palm rest (qty 3)
pitch 0.45 mm · tap 2.05 mm · clearance 2.9 mm · PH1 / Torx T8
Base cover (qty 9)
pitch 0.45 mm · tap 2.05 mm · clearance 2.9 mm · PH1 / Torx T8
Display (qty 6, pan)
pitch 0.45 mm · tap 2.05 mm · clearance 2.9 mm · PH1 / Torx T8
Display bezel (qty 6)
pitch 0.45 mm · tap 2.05 mm · clearance 2.9 mm · PH1 / Torx T8
Fan (qty 3)
pitch 0.45 mm · tap 2.05 mm · clearance 2.9 mm · PH1 / Torx T8
Heat sink (qty 2)
pitch 0.45 mm · tap 2.05 mm · clearance 2.9 mm · PH1 / Torx T8
Hinge (qty 5)
pitch 0.45 mm · tap 2.05 mm · clearance 2.9 mm · PH1 / Torx T8
System board (qty 6, white)
pitch 0.45 mm · tap 2.05 mm · clearance 2.9 mm · PH1 / Torx T8
Display (qty 4)
pitch 0.5 mm · tap 2.5 mm · clearance 3.4 mm · PH1 / Torx T10
Hard drive (qty 1)
pitch 0.5 mm · tap 2.5 mm · clearance 3.4 mm · PH1 / Torx T10
How to check the screw before you buy
- Laptop covers and brackets often mix two or three lengths of the same thread, so lay the screws out in the order they came out (a magnetic mat or a sheet of paper with the hole pattern drawn on it works).
- Diameter: across the threads an M2 screw measures about 2 mm with calipers (usually a hair under). This device also uses M2.5 / M3, so measure each screw rather than assuming they match.
- Pitch: 0.4 mm from one thread crest to the next (25 crests per centimetre). A thread pitch gauge or the pitch-gauge tool settles it in seconds.
- Length: for pan head screws, measure from under the head to the tip (countersunk heads are the exception: they are measured overall).
- The records span 3–12 mm, which means different positions take different lengths — match each hole to its own screw.
- Driver: the source does not name the drive. Standard M2 heads take PH0 for Phillips and T6 for Torx, and a 1.5 mm hex key for socket heads; a bit that fits loosely will cam out and strip the head.
- Tightening: no device-specific torque is published in these records. The site's general figure for M2 is about 25-40 N·cm into metal threads and 12-20 N·cm into plastic bosses; snug it up and stop.
Common mix-ups with M2 / M2.5 / M3
- The standard M.2 SSD screw is M2 x 3mm, but some laptops and handhelds use non-standard lengths or head shapes.
- Dell/HP/Lenovo manuals often list screws only by torque or head shape, so community teardowns are needed for diameter.
- Server drive caddy screws (Dell, HP) are usually M3 in very short lengths (3-4mm) because they bite into thin sheet metal — they are NOT the 6-32 UNC screws that go into the drive's own side holes.
Buy these screws at TechSpare Warehouse
In stock and shipped from South Carolina. Our black screws are Phillips wafer head (low profile); match the head style and length to the original before you order.
-
M2 x 3mm Screws for Dell XPS 13 9340 Base Cover SSD Shield 10-Pack Black
$4.99 -
10x M2 x 3mm Phillips Screws for Lenovo ThinkPad X131e Chromebook WiFi SSD
$4.99
-
M2 x 4mm Phillips Wafer Head Machine Screws Black 50-Pack Laptop SSD Repair
$4.49 each · min. 2
-
M2 x 4mm Screws for Dell Latitude 5530 SSD Type-C Bracket 10-Pack Black
$4.99
-
M2.5 x 12mm Phillips Wafer Head Screw for Turntable Cartridge Headshell Mount - Pack of 50 Black
$6.49 -
M2.5 x 12mm Phillips Wafer Head Screw for Laptop Bottom Cover Replacement - Single Replacement Black
$0.10 each · min. 50
-
ASUS ROG Strix G15 G513R Replacement Screws Sold Individually – M1.6 x 3mm, M2 x 2.5mm, M2 x 3mm, M2.5 x 6mm Phillips Wafer Head, Black
$0.10Choose size -
ASUS ROG Strix G17 G713 Replacement Screws Sold Individually – M1.6 x 3mm, M2 x 2.5mm, M2 x 3mm, M2.5 x 6mm Phillips Wafer Head, Black
$0.10Choose size
More in Laptops & PCs
The same screw also fits
Devices whose records share a thread with Dell Latitude C500, closest length match first.
- Dell Latitude 5431 also M2 × 3 mm
- Dell 15 DC15255 also M2 × 3 mm
- HP EliteBook 745 G6 also M2 × 3 mm
- Lenovo G410 also M2 × 3 mm
- Lenovo ThinkPad T410i also M2 × 3 mm
- Lenovo ThinkPad C13 Yoga Gen 1 also M2.5 × 5 mm
- HP EliteBook 846 G6 also M2 × 3 mm
- HP Compaq 515 also M2 × 3 mm
Questions about Dell Latitude C500 screws
- What size screw does Dell Latitude C500 use?
- M2 × 3 mm for base cover (qty 2); M2 × 3 mm for bracket (qty 2); M2 × 3 mm for display (qty 2); M2 × 3 mm for heat sink (qty 2); M2 × 3 mm for palm rest (qty 3); M2 × 3 mm for unspecified (qty 2); M2 × 4 mm for display (qty 5); M2.5 × 12 mm for keyboard (qty 5); M2.5 × 12 mm for palm rest (qty 3); M2.5 × 5 mm for base cover (qty 9); M2.5 × 5 mm for display (qty 6, pan); M2.5 × 5 mm for display bezel (qty 6); M2.5 × 5 mm for fan (qty 3); M2.5 × 5 mm for heat sink (qty 2); M2.5 × 5 mm for hinge (qty 5); M2.5 × 5 mm for system board (qty 6, white); M3 × 3 mm for display (qty 4); M3 × 5 mm for hard drive (qty 1).
- How long are the screws in Dell Latitude C500?
- The records range from 3 to 12 mm depending on the position, so match each screw to its own hole.
- What is the thread pitch of an M2 screw?
- 0.4 mm (coarse), which is the standard pitch for M2 machine screws; a 0.25 mm fine pitch exists but is uncommon. The tap drill is 1.6 mm and the normal clearance hole is 2.4 mm.
- What screwdriver do I need for Dell Latitude C500?
- The sources do not name the drive. For M2, Phillips heads normally take PH0 and Torx heads T6; socket heads take a 1.5 mm hex key.
- Can I use an imperial screw instead of M2?
- No. Imperial look-alike: #2-56 UNC (2.18 mm) is close but not interchangeable. Use a true M2 screw so it does not cross-thread or strip the hole.
- Where can I buy replacement screws for Dell Latitude C500?
- TechSpareWarehouse (our own store) lists M2 x 3mm, M2 x 4mm and M2.5 x 12mm, which match lengths in the records above.