Dell Latitude D610 screw size
M2 / M2.5 / M3 · 3 to 8 mm long
Our records put Dell Latitude D610 on M2, M2.5 and M3 screws in lengths from 3 to 8 mm.
There are 12 separate fitment records for it, including display (qty 4) (M2), system board (qty 5) (M2) and unspecified (qty 1, Phillips) (M2), plus 9 more in the table below.
Head and drive, as the sources state them: Phillips drive.
12 of the 12 records are marked confirmed, drawn from 1 source (dl.dell.com).
M2 means a 2 mm nominal diameter with a 0.4 mm thread pitch. Imperial look-alike: #2-56 UNC (2.18 mm) is close but not interchangeable.
Dell Latitude D610 screw specifications
One row per fitment record. Head, drive are shown only where the source states them; pitch is the ISO coarse pitch for the thread.
| Thread | Length | Pitch | Head | Drive | Where it goes | Status |
|---|---|---|---|---|---|---|
| M2 | 3 mm | 0.4 mm | not stated | not stated | Display (qty 4) | Confirmed |
| M2 | 3 mm | 0.4 mm | not stated | not stated | System board (qty 5) | Confirmed |
| M2 | 3 mm | 0.4 mm | not stated | Phillips | Unspecified (qty 1, Phillips) | Confirmed |
| M2.5 | 4 mm | 0.45 mm | not stated | not stated | System board (qty 4) | Confirmed |
| M2.5 | 5 mm | 0.45 mm | not stated | not stated | Display (qty 4, captive)captive | Confirmed |
| M2.5 | 5 mm | 0.45 mm | not stated | not stated | Display bezel (qty 6) | Confirmed |
| M2.5 | 5 mm | 0.45 mm | not stated | not stated | Keyboard (qty 2) | Confirmed |
| M2.5 | 5 mm | 0.45 mm | not stated | not stated | Palm rest (qty 3) | Confirmed |
| M2.5 | 5 mm | 0.45 mm | not stated | not stated | Speaker (qty 2) | Confirmed |
| M2.5 | 8 mm | 0.45 mm | not stated | not stated | Fan (qty 2) | Confirmed |
| M2.5 | 8 mm | 0.45 mm | not stated | not stated | Palm rest (qty 13) | Confirmed |
| M3 | 3 mm | 0.5 mm | not stated | Phillips | Hard drive (qty 2, Phillips) | Confirmed |
Fitment records and sources
Display (qty 4)
pitch 0.4 mm · tap 1.6 mm · clearance 2.4 mm · PH0 / Torx T6
System board (qty 5)
pitch 0.4 mm · tap 1.6 mm · clearance 2.4 mm · PH0 / Torx T6
Unspecified (qty 1, Phillips)
pitch 0.4 mm · tap 1.6 mm · clearance 2.4 mm · PH0 / Torx T6
System board (qty 4)
pitch 0.45 mm · tap 2.05 mm · clearance 2.9 mm · PH1 / Torx T8
Display (qty 4, captive)
pitch 0.45 mm · tap 2.05 mm · clearance 2.9 mm · PH1 / Torx T8
Display bezel (qty 6)
pitch 0.45 mm · tap 2.05 mm · clearance 2.9 mm · PH1 / Torx T8
Keyboard (qty 2)
pitch 0.45 mm · tap 2.05 mm · clearance 2.9 mm · PH1 / Torx T8
Palm rest (qty 3)
pitch 0.45 mm · tap 2.05 mm · clearance 2.9 mm · PH1 / Torx T8
Speaker (qty 2)
pitch 0.45 mm · tap 2.05 mm · clearance 2.9 mm · PH1 / Torx T8
Fan (qty 2)
pitch 0.45 mm · tap 2.05 mm · clearance 2.9 mm · PH1 / Torx T8
Palm rest (qty 13)
pitch 0.45 mm · tap 2.05 mm · clearance 2.9 mm · PH1 / Torx T8
Hard drive (qty 2, Phillips)
pitch 0.5 mm · tap 2.5 mm · clearance 3.4 mm · PH1 / Torx T10
How to check the screw before you buy
- A screw that is even 1 mm too long in a laptop base can push into the keyboard, battery or a board trace, so match the length position by position.
- Diameter: across the threads an M2 screw measures about 2 mm with calipers (usually a hair under). This device also uses M2.5 / M3, so measure each screw rather than assuming they match.
- Pitch: 0.4 mm from one thread crest to the next (25 crests per centimetre). A thread pitch gauge or the pitch-gauge tool settles it in seconds.
- Length: measure from under the head to the tip for pan, button, wafer and cap heads; countersunk (flat) heads are measured overall.
- The records span 3–8 mm, which means different positions take different lengths — match each hole to its own screw.
- Driver: the source names a Phillips drive. For comparison, standard M2 heads take PH0 (Phillips) or T6 (Torx), or a 1.5 mm hex key.
- Tightening: no device-specific torque is published in these records. The site's general figure for M2 is about 25-40 N·cm into metal threads and 12-20 N·cm into plastic bosses; snug it up and stop.
Common mix-ups with M2 / M2.5 / M3
- The standard M.2 SSD screw is M2 x 3mm, but some laptops and handhelds use non-standard lengths or head shapes.
- Dell/HP/Lenovo manuals often list screws only by torque or head shape, so community teardowns are needed for diameter.
- Server drive caddy screws (Dell, HP) are usually M3 in very short lengths (3-4mm) because they bite into thin sheet metal — they are NOT the 6-32 UNC screws that go into the drive's own side holes.
Buy these screws at TechSpare Warehouse
In stock and shipped from South Carolina. Our black screws are Phillips wafer head (low profile); match the head style and length to the original before you order.
-
M2 x 3mm Screws for Dell XPS 13 9340 Base Cover SSD Shield 10-Pack Black
$4.99 -
10x M2 x 3mm Phillips Screws for Lenovo ThinkPad X131e Chromebook WiFi SSD
$4.99
-
M2.5 x 4mm Screws for Lenovo IdeaPad 5 Pro 14 Display Hinge 10-Pack Black
$4.99 -
M2.5 x 4mm Screws for Lenovo IdeaPad 5 Pro 14 System Board Hinge 10-Pack Black
$4.99
-
M2.5 x 5mm Screws Compatible with Dell XPS 14 9440 Display Assembly 10-Pack
$4.99 -
M2.5 x 5mm Phillips Wafer Head Screw for Action Camera Protective Housing - Pack of 50 Black
$4.79 each · min. 2
-
ASUS ROG Strix G15 G513R Replacement Screws Sold Individually – M1.6 x 3mm, M2 x 2.5mm, M2 x 3mm, M2.5 x 6mm Phillips Wafer Head, Black
$0.10Choose size -
ASUS ROG Strix G17 G713 Replacement Screws Sold Individually – M1.6 x 3mm, M2 x 2.5mm, M2 x 3mm, M2.5 x 6mm Phillips Wafer Head, Black
$0.10Choose size
More in Laptops & PCs
The same screw also fits
Devices whose records share a thread with Dell Latitude D610, closest length match first.
- Dell Inspiron 15 7591 also M2 × 3 mm
- Lenovo ThinkPad T500 also M2 × 3 mm
- Dell Inspiron 8100 also M2 × 3 mm
- Acer Aspire 4935G also M2 × 3 mm
- Lenovo ideapad 320E-17IKB also M2 × 3 mm
- Laptop hinge covers & trim panels also M2 × 3 mm
- Dell Latitude 3180 also M2 × 3 mm
- HP EliteBook 830 G5 / 836 G5 also M2 × 3 mm
Questions about Dell Latitude D610 screws
- What size screw does Dell Latitude D610 use?
- M2 × 3 mm for display (qty 4); M2 × 3 mm for system board (qty 5); M2 × 3 mm for unspecified (qty 1, Phillips); M2.5 × 4 mm for system board (qty 4); M2.5 × 5 mm for display (qty 4, captive); M2.5 × 5 mm for display bezel (qty 6); M2.5 × 5 mm for keyboard (qty 2); M2.5 × 5 mm for palm rest (qty 3); M2.5 × 5 mm for speaker (qty 2); M2.5 × 8 mm for fan (qty 2); M2.5 × 8 mm for palm rest (qty 13); M3 × 3 mm for hard drive (qty 2, Phillips).
- How long are the screws in Dell Latitude D610?
- The records range from 3 to 8 mm depending on the position, so match each screw to its own hole.
- What is the thread pitch of an M2 screw?
- 0.4 mm (coarse), which is the standard pitch for M2 machine screws; a 0.25 mm fine pitch exists but is uncommon. The tap drill is 1.6 mm and the normal clearance hole is 2.4 mm.
- What screwdriver do I need for Dell Latitude D610?
- The source lists a Phillips drive. Standard M2 heads otherwise take PH0 (Phillips) or T6 (Torx), or a 1.5 mm hex key.
- Can I use an imperial screw instead of M2?
- No. Imperial look-alike: #2-56 UNC (2.18 mm) is close but not interchangeable. Use a true M2 screw so it does not cross-thread or strip the hole.
- Where can I buy replacement screws for Dell Latitude D610?
- TechSpareWarehouse (our own store) lists M2 x 3mm, M2.5 x 4mm and M2.5 x 5mm, which match lengths in the records above.