Dell Latitude E6420 XFR screw size
M2 / M2.5 / M3 · 3 to 15 mm long
If you are replacing a screw on Dell Latitude E6420 XFR, the thread is M2, M2.5 and M3 in lengths from 3 to 15 mm.
There are 26 separate fitment records for it, including unspecified (qty 2) (M2), I/O board (qty 2) (M2) and card reader (qty 3) (M2), plus 23 more in the table below.
Head and drive, as the sources state them: shoulder screw head.
26 of the 26 records are marked confirmed, drawn from 1 source (dl.dell.com).
For reference, M2 is 2 mm across the threads at 0.4 mm pitch. The imperial size people confuse it with: #2-56 UNC (2.18 mm) is close but not interchangeable.
Dell Latitude E6420 XFR screw specifications
One row per fitment record. Head, drive are shown only where the source states them; pitch is the ISO coarse pitch for the thread.
| Thread | Length | Pitch | Head | Drive | Where it goes | Status |
|---|---|---|---|---|---|---|
| M2 | 15 mm | 0.4 mm | not stated | not stated | Unspecified (qty 2) | Confirmed |
| M2 | 3 mm | 0.4 mm | not stated | not stated | I/O board (qty 2) | Confirmed |
| M2 | 3 mm | 0.4 mm | not stated | not stated | Card reader (qty 3) | Confirmed |
| M2 | 3 mm | 0.4 mm | not stated | not stated | Display (qty 1) | Confirmed |
| M2 | 3 mm | 0.4 mm | not stated | not stated | Unspecified (qty 4, white) | Confirmed |
| M2.5 | 10 mm | 0.45 mm | not stated | not stated | System board (qty 1) | Confirmed |
| M2.5 | 10 mm | 0.45 mm | Shoulder screw | not stated | Unspecified (qty 2, shoulder) | Confirmed |
| M2.5 | 5 mm | 0.45 mm | not stated | not stated | I/O board (qty 1) | Confirmed |
| M2.5 | 5 mm | 0.45 mm | not stated | not stated | LED board (qty 4) | Confirmed |
| M2.5 | 5 mm | 0.45 mm | not stated | not stated | Base cover (qty 7) | Confirmed |
| M2.5 | 5 mm | 0.45 mm | not stated | not stated | Card reader (qty 2) | Confirmed |
| M2.5 | 5 mm | 0.45 mm | not stated | not stated | Fan (qty 3) | Confirmed |
| M2.5 | 5 mm | 0.45 mm | not stated | not stated | Hinge (qty 1) | Confirmed |
| M2.5 | 5 mm | 0.45 mm | not stated | not stated | Keyboard (qty 2) | Confirmed |
| M2.5 | 5 mm | 0.45 mm | not stated | not stated | System board (qty 3) | Confirmed |
| M2.5 | 5 mm | 0.45 mm | not stated | not stated | Unspecified (qty 7) | Confirmed |
| M2.5 | 8 mm | 0.45 mm | not stated | not stated | Display (qty 4) | Confirmed |
| M2.5 | 8 mm | 0.45 mm | not stated | not stated | Hinge (qty 3) | Confirmed |
| M2.5 | 8 mm | 0.45 mm | not stated | not stated | Palm rest (qty 16) | Confirmed |
| M2.5 | 8 mm | 0.45 mm | not stated | not stated | Unspecified (qty 18) | Confirmed |
| M2.5 | 8 mm | 0.45 mm | not stated | not stated | Wireless card (qty 5) | Confirmed |
| M3 | 3 mm | 0.5 mm | not stated | not stated | Chassis/frame (qty 4) | Confirmed |
| M3 | 3 mm | 0.5 mm | not stated | not stated | Hinge (qty 1) | Confirmed |
| M3 | 3 mm | 0.5 mm | not stated | not stated | Unspecified (qty 4) | Confirmed |
| M3 | 4 mm | 0.5 mm | not stated | not stated | Hard drive (qty 4) | Confirmed |
| M3 | 4 mm | 0.5 mm | not stated | not stated | Unspecified (qty 4) | Confirmed |
Fitment records and sources
Unspecified (qty 2)
pitch 0.4 mm · tap 1.6 mm · clearance 2.4 mm · PH0 / Torx T6
I/O board (qty 2)
pitch 0.4 mm · tap 1.6 mm · clearance 2.4 mm · PH0 / Torx T6
Card reader (qty 3)
pitch 0.4 mm · tap 1.6 mm · clearance 2.4 mm · PH0 / Torx T6
Display (qty 1)
pitch 0.4 mm · tap 1.6 mm · clearance 2.4 mm · PH0 / Torx T6
Unspecified (qty 4, white)
pitch 0.4 mm · tap 1.6 mm · clearance 2.4 mm · PH0 / Torx T6
System board (qty 1)
pitch 0.45 mm · tap 2.05 mm · clearance 2.9 mm · PH1 / Torx T8
Unspecified (qty 2, shoulder)
pitch 0.45 mm · tap 2.05 mm · clearance 2.9 mm · PH1 / Torx T8
I/O board (qty 1)
pitch 0.45 mm · tap 2.05 mm · clearance 2.9 mm · PH1 / Torx T8
LED board (qty 4)
pitch 0.45 mm · tap 2.05 mm · clearance 2.9 mm · PH1 / Torx T8
Base cover (qty 7)
pitch 0.45 mm · tap 2.05 mm · clearance 2.9 mm · PH1 / Torx T8
Card reader (qty 2)
pitch 0.45 mm · tap 2.05 mm · clearance 2.9 mm · PH1 / Torx T8
Fan (qty 3)
pitch 0.45 mm · tap 2.05 mm · clearance 2.9 mm · PH1 / Torx T8
Hinge (qty 1)
pitch 0.45 mm · tap 2.05 mm · clearance 2.9 mm · PH1 / Torx T8
Keyboard (qty 2)
pitch 0.45 mm · tap 2.05 mm · clearance 2.9 mm · PH1 / Torx T8
System board (qty 3)
pitch 0.45 mm · tap 2.05 mm · clearance 2.9 mm · PH1 / Torx T8
Unspecified (qty 7)
pitch 0.45 mm · tap 2.05 mm · clearance 2.9 mm · PH1 / Torx T8
Display (qty 4)
pitch 0.45 mm · tap 2.05 mm · clearance 2.9 mm · PH1 / Torx T8
Hinge (qty 3)
pitch 0.45 mm · tap 2.05 mm · clearance 2.9 mm · PH1 / Torx T8
Palm rest (qty 16)
pitch 0.45 mm · tap 2.05 mm · clearance 2.9 mm · PH1 / Torx T8
Unspecified (qty 18)
pitch 0.45 mm · tap 2.05 mm · clearance 2.9 mm · PH1 / Torx T8
Wireless card (qty 5)
pitch 0.45 mm · tap 2.05 mm · clearance 2.9 mm · PH1 / Torx T8
Chassis/frame (qty 4)
pitch 0.5 mm · tap 2.5 mm · clearance 3.4 mm · PH1 / Torx T10
Hinge (qty 1)
pitch 0.5 mm · tap 2.5 mm · clearance 3.4 mm · PH1 / Torx T10
Unspecified (qty 4)
pitch 0.5 mm · tap 2.5 mm · clearance 3.4 mm · PH1 / Torx T10
Hard drive (qty 4)
pitch 0.5 mm · tap 2.5 mm · clearance 3.4 mm · PH1 / Torx T10
Unspecified (qty 4)
pitch 0.5 mm · tap 2.5 mm · clearance 3.4 mm · PH1 / Torx T10
How to check the screw before you buy
- Laptop covers and brackets often mix two or three lengths of the same thread, so lay the screws out in the order they came out (a magnetic mat or a sheet of paper with the hole pattern drawn on it works).
- Diameter: across the threads an M2 screw measures about 2 mm with calipers (usually a hair under). This device also uses M2.5 / M3, so measure each screw rather than assuming they match.
- Pitch: 0.4 mm from one thread crest to the next (25 crests per centimetre). A thread pitch gauge or the pitch-gauge tool settles it in seconds.
- Length: for shoulder screw screws, measure from under the head to the tip (countersunk heads are the exception: they are measured overall).
- The records span 3–15 mm, which means different positions take different lengths — match each hole to its own screw.
- Driver: the source does not name the drive. Standard M2 heads take PH0 for Phillips and T6 for Torx, and a 1.5 mm hex key for socket heads; a bit that fits loosely will cam out and strip the head.
- Tightening: no device-specific torque is published in these records. The site's general figure for M2 is about 25-40 N·cm into metal threads and 12-20 N·cm into plastic bosses; snug it up and stop.
Common mix-ups with M2 / M2.5 / M3
- Xbox Series X internal chassis screws are M3, not M2 (confirmed on iFixit) — a widespread misconception.
- Dell/HP/Lenovo manuals often list screws only by torque or head shape, so community teardowns are needed for diameter.
- Part numbers can embed a thread code (e.g. ifm fibre fittings with 'M3') that refers to a fitting thread, not a chassis screw.
Buy these screws at TechSpare Warehouse
In stock and shipped from South Carolina. Our black screws are Phillips wafer head (low profile); match the head style and length to the original before you order.
-
M2 x 3mm Screws for Dell XPS 13 9340 Base Cover SSD Shield 10-Pack Black
$4.99 -
10x M2 x 3mm Phillips Screws for Lenovo ThinkPad X131e Chromebook WiFi SSD
$4.99
-
M2.5 x 10mm Phillips Wafer Head Screw for Turntable Cartridge Headshell Mount - Pack of 50 Black
$5.99 -
M2.5 x 10mm Phillips Wafer Head Screw for ASUS TUF Gaming A15/F15 Laptop Repair - Single Replacement Black
$0.10 each · min. 50
-
M2.5 x 5mm Screws Compatible with Dell XPS 14 9440 Display Assembly 10-Pack
$4.99 -
M2.5 x 5mm Phillips Wafer Head Screw for Action Camera Protective Housing - Pack of 50 Black
$4.79 each · min. 2
-
ASUS ROG Strix G15 G513R Replacement Screws Sold Individually – M1.6 x 3mm, M2 x 2.5mm, M2 x 3mm, M2.5 x 6mm Phillips Wafer Head, Black
$0.10Choose size -
ASUS ROG Strix G17 G713 Replacement Screws Sold Individually – M1.6 x 3mm, M2 x 2.5mm, M2 x 3mm, M2.5 x 6mm Phillips Wafer Head, Black
$0.10Choose size
More in Laptops & PCs
The same screw also fits
Devices whose records share a thread with Dell Latitude E6420 XFR, closest length match first.
- Dell Latitude 3530 also M2 × 3 mm
- Dell Latitude C600 also M2 × 3 mm
- HP ZBook Firefly 14 G10 also M2 × 3 mm
- Lenovo ideapad 330-15IGM also M2.5 × 5 mm
- Acer Aspire 7315 also M2 × 3 mm
- Acer TravelMate 4730 also M2 × 3 mm
- HP Compaq 6715b also M2 × 3 mm
- Lenovo V310-14IKB also M2 × 3 mm
Questions about Dell Latitude E6420 XFR screws
- What size screw does Dell Latitude E6420 XFR use?
- M2 × 15 mm for unspecified (qty 2); M2 × 3 mm for I/O board (qty 2); M2 × 3 mm for card reader (qty 3); M2 × 3 mm for display (qty 1); M2 × 3 mm for unspecified (qty 4, white); M2.5 × 10 mm for system board (qty 1); M2.5 × 10 mm for unspecified (qty 2, shoulder); M2.5 × 5 mm for I/O board (qty 1); M2.5 × 5 mm for LED board (qty 4); M2.5 × 5 mm for base cover (qty 7); M2.5 × 5 mm for card reader (qty 2); M2.5 × 5 mm for fan (qty 3); M2.5 × 5 mm for hinge (qty 1); M2.5 × 5 mm for keyboard (qty 2); M2.5 × 5 mm for system board (qty 3); M2.5 × 5 mm for unspecified (qty 7); M2.5 × 8 mm for display (qty 4); M2.5 × 8 mm for hinge (qty 3); M2.5 × 8 mm for palm rest (qty 16); M2.5 × 8 mm for unspecif.
- How long are the screws in Dell Latitude E6420 XFR?
- The records range from 3 to 15 mm depending on the position, so match each screw to its own hole.
- What is the thread pitch of an M2 screw?
- 0.4 mm (coarse), which is the standard pitch for M2 machine screws; a 0.25 mm fine pitch exists but is uncommon. The tap drill is 1.6 mm and the normal clearance hole is 2.4 mm.
- What screwdriver do I need for Dell Latitude E6420 XFR?
- The sources do not name the drive. For M2, Phillips heads normally take PH0 and Torx heads T6; socket heads take a 1.5 mm hex key.
- Can I use an imperial screw instead of M2?
- No. Imperial look-alike: #2-56 UNC (2.18 mm) is close but not interchangeable. Use a true M2 screw so it does not cross-thread or strip the hole.
- Where can I buy replacement screws for Dell Latitude E6420 XFR?
- TechSpareWarehouse (our own store) lists M2 x 3mm, M2.5 x 10mm and M2.5 x 5mm, which match lengths in the records above.