Dell Precision M90 screw size
M2 / M2.5 / M3 · 3 to 8 mm long
The screws used on Dell Precision M90 are M2, M2.5 and M3 in lengths from 3 to 8 mm.
There are 17 separate fitment records for it, including battery (qty 4) (M2), card reader (qty 4) (M2) and display (qty 8) (M2), plus 14 more in the table below.
Head and drive, as the sources state them: shoulder screw head.
17 of the 17 records are marked confirmed, drawn from 1 source (dl.dell.com).
An M2 screw is 2 mm in diameter with a 0.4 mm pitch, tapped with a 1.6 mm drill; imperial look-alike: #2-56 UNC (2.18 mm) is close but not interchangeable.
Dell Precision M90 screw specifications
One row per fitment record. Head, drive are shown only where the source states them; pitch is the ISO coarse pitch for the thread.
| Thread | Length | Pitch | Head | Drive | Where it goes | Status |
|---|---|---|---|---|---|---|
| M2 | 3 mm | 0.4 mm | not stated | not stated | Battery (qty 4) | Confirmed |
| M2 | 3 mm | 0.4 mm | not stated | not stated | Card reader (qty 4) | Confirmed |
| M2 | 3 mm | 0.4 mm | not stated | not stated | Display (qty 8) | Confirmed |
| M2 | 3 mm | 0.4 mm | not stated | not stated | Unspecified (qty 1) | Confirmed |
| M2.5 | 5 mm | 0.45 mm | not stated | not stated | Battery (qty 4) | Confirmed |
| M2.5 | 5 mm | 0.45 mm | not stated | not stated | Display (qty 4) | Confirmed |
| M2.5 | 5 mm | 0.45 mm | Shoulder screw | not stated | Display bezel (qty 4, shoulder) | Confirmed |
| M2.5 | 5 mm | 0.45 mm | not stated | not stated | Fan (qty 2) | Confirmed |
| M2.5 | 5 mm | 0.45 mm | not stated | not stated | Keyboard (qty 2) | Confirmed |
| M2.5 | 5 mm | 0.45 mm | not stated | not stated | Palm rest (qty 6) | Confirmed |
| M2.5 | 5 mm | 0.45 mm | not stated | not stated | Speaker (qty 4) | Confirmed |
| M2.5 | 5 mm | 0.45 mm | not stated | not stated | System board (qty 4) | Confirmed |
| M2.5 | 5 mm | 0.45 mm | not stated | not stated | Unspecified (qty 1) | Confirmed |
| M2.5 | 8 mm | 0.45 mm | not stated | not stated | Optical drive (qty 3) | Confirmed |
| M2.5 | 8 mm | 0.45 mm | not stated | not stated | Palm rest (qty 12) | Confirmed |
| M2.5 | 8 mm | 0.45 mm | not stated | not stated | Unspecified (qty 1) | Confirmed |
| M3 | 3 mm | 0.5 mm | not stated | not stated | Hard drive (qty 2) | Confirmed |
Fitment records and sources
Battery (qty 4)
pitch 0.4 mm · tap 1.6 mm · clearance 2.4 mm · PH0 / Torx T6
Card reader (qty 4)
pitch 0.4 mm · tap 1.6 mm · clearance 2.4 mm · PH0 / Torx T6
Display (qty 8)
pitch 0.4 mm · tap 1.6 mm · clearance 2.4 mm · PH0 / Torx T6
Unspecified (qty 1)
pitch 0.4 mm · tap 1.6 mm · clearance 2.4 mm · PH0 / Torx T6
Battery (qty 4)
pitch 0.45 mm · tap 2.05 mm · clearance 2.9 mm · PH1 / Torx T8
Display (qty 4)
pitch 0.45 mm · tap 2.05 mm · clearance 2.9 mm · PH1 / Torx T8
Display bezel (qty 4, shoulder)
pitch 0.45 mm · tap 2.05 mm · clearance 2.9 mm · PH1 / Torx T8
Fan (qty 2)
pitch 0.45 mm · tap 2.05 mm · clearance 2.9 mm · PH1 / Torx T8
Keyboard (qty 2)
pitch 0.45 mm · tap 2.05 mm · clearance 2.9 mm · PH1 / Torx T8
Palm rest (qty 6)
pitch 0.45 mm · tap 2.05 mm · clearance 2.9 mm · PH1 / Torx T8
Speaker (qty 4)
pitch 0.45 mm · tap 2.05 mm · clearance 2.9 mm · PH1 / Torx T8
System board (qty 4)
pitch 0.45 mm · tap 2.05 mm · clearance 2.9 mm · PH1 / Torx T8
Unspecified (qty 1)
pitch 0.45 mm · tap 2.05 mm · clearance 2.9 mm · PH1 / Torx T8
Optical drive (qty 3)
pitch 0.45 mm · tap 2.05 mm · clearance 2.9 mm · PH1 / Torx T8
Palm rest (qty 12)
pitch 0.45 mm · tap 2.05 mm · clearance 2.9 mm · PH1 / Torx T8
Unspecified (qty 1)
pitch 0.45 mm · tap 2.05 mm · clearance 2.9 mm · PH1 / Torx T8
Hard drive (qty 2)
pitch 0.5 mm · tap 2.5 mm · clearance 3.4 mm · PH1 / Torx T10
How to check the screw before you buy
- Laptop covers and brackets often mix two or three lengths of the same thread, so lay the screws out in the order they came out (a magnetic mat or a sheet of paper with the hole pattern drawn on it works).
- Diameter: across the threads an M2 screw measures about 2 mm with calipers (usually a hair under). This device also uses M2.5 / M3, so measure each screw rather than assuming they match.
- Pitch: 0.4 mm from one thread crest to the next (25 crests per centimetre). A thread pitch gauge or the pitch-gauge tool settles it in seconds.
- Length: for shoulder screw screws, measure from under the head to the tip (countersunk heads are the exception: they are measured overall).
- The records span 3–8 mm, which means different positions take different lengths — match each hole to its own screw.
- Driver: the source does not name the drive. Standard M2 heads take PH0 for Phillips and T6 for Torx, and a 1.5 mm hex key for socket heads; a bit that fits loosely will cam out and strip the head.
- Tightening: no device-specific torque is published in these records. The site's general figure for M2 is about 25-40 N·cm into metal threads and 12-20 N·cm into plastic bosses; snug it up and stop.
Common mix-ups with M2 / M2.5 / M3
- The standard M.2 SSD screw is M2 x 3mm, but some laptops and handhelds use non-standard lengths or head shapes.
- Dell/HP/Lenovo manuals often list screws only by torque or head shape, so community teardowns are needed for diameter.
- Thorlabs' 16mm cage system standard plates use dual 4-40 (UNC) and M3 taps on the same plate (e.g., SP01), so metric and imperial fasteners are both valid depending on the region/kit purchased.
Buy these screws at TechSpare Warehouse
In stock and shipped from South Carolina. Our black screws are Phillips wafer head (low profile); match the head style and length to the original before you order.
-
M2 x 3mm Screws for Dell XPS 13 9340 Base Cover SSD Shield 10-Pack Black
$4.99 -
10x M2 x 3mm Phillips Screws for Lenovo ThinkPad X131e Chromebook WiFi SSD
$4.99
-
M2.5 x 5mm Screws Compatible with Dell XPS 14 9440 Display Assembly 10-Pack
$4.99 -
M2.5 x 5mm Phillips Wafer Head Screw for Action Camera Protective Housing - Pack of 50 Black
$4.79 each · min. 2
-
M2.5 x 8mm Screws for Retevis RT27 Radio Belt Clip 10-Pack Black Phillips
$4.99 -
M2.5 x 8mm Screws for Raspberry Pi 5 Case and PoE HAT 10-Pack Black
$4.99 -
ASUS ROG Strix G15 G513R Replacement Screws Sold Individually – M1.6 x 3mm, M2 x 2.5mm, M2 x 3mm, M2.5 x 6mm Phillips Wafer Head, Black
$0.10Choose size -
ASUS ROG Strix G17 G713 Replacement Screws Sold Individually – M1.6 x 3mm, M2 x 2.5mm, M2 x 3mm, M2.5 x 6mm Phillips Wafer Head, Black
$0.10Choose size
More in Laptops & PCs
The same screw also fits
Devices whose records share a thread with Dell Precision M90, closest length match first.
- Lenovo Legion y520-15ikba also M2 × 3 mm
- Dell Vostro 1500 also M2 × 3 mm
- Lenovo ThinkPad Edge E320 also M2 × 3 mm
- Lenovo Yoga Pro 7 14AKP10 also M2.5 × 5 mm
- Lenovo B41-35 also M2 × 3 mm
- HP ProBook 440 G2 also M2 × 3 mm
- Dell Alienware m17 also M2 × 3 mm
- Toshiba Satellite Pro M10 also M2 × 3 mm
Questions about Dell Precision M90 screws
- What size screw does Dell Precision M90 use?
- M2 × 3 mm for battery (qty 4); M2 × 3 mm for card reader (qty 4); M2 × 3 mm for display (qty 8); M2 × 3 mm for unspecified (qty 1); M2.5 × 5 mm for battery (qty 4); M2.5 × 5 mm for display (qty 4); M2.5 × 5 mm for display bezel (qty 4, shoulder); M2.5 × 5 mm for fan (qty 2); M2.5 × 5 mm for keyboard (qty 2); M2.5 × 5 mm for palm rest (qty 6); M2.5 × 5 mm for speaker (qty 4); M2.5 × 5 mm for system board (qty 4); M2.5 × 5 mm for unspecified (qty 1); M2.5 × 8 mm for optical drive (qty 3); M2.5 × 8 mm for palm rest (qty 12); M2.5 × 8 mm for unspecified (qty 1); M3 × 3 mm for hard drive (qty 2).
- How long are the screws in Dell Precision M90?
- The records range from 3 to 8 mm depending on the position, so match each screw to its own hole.
- What is the thread pitch of an M2 screw?
- 0.4 mm (coarse), which is the standard pitch for M2 machine screws; a 0.25 mm fine pitch exists but is uncommon. The tap drill is 1.6 mm and the normal clearance hole is 2.4 mm.
- What screwdriver do I need for Dell Precision M90?
- The sources do not name the drive. For M2, Phillips heads normally take PH0 and Torx heads T6; socket heads take a 1.5 mm hex key.
- Can I use an imperial screw instead of M2?
- No. Imperial look-alike: #2-56 UNC (2.18 mm) is close but not interchangeable. Use a true M2 screw so it does not cross-thread or strip the hole.
- Where can I buy replacement screws for Dell Precision M90?
- TechSpareWarehouse (our own store) lists M2 x 3mm, M2.5 x 5mm and M2.5 x 8mm, which match lengths in the records above.