Dell Studio 1536 screw size
M2 / M3 · 3 mm long
Dell Studio 1536 takes M2 and M3 metric screws, 3 mm long.
There are 2 separate fitment records for it, including unspecified (qty 1) (M2) and hard drive (qty 4) (M3).
2 of the 2 records are marked confirmed, drawn from 1 source (dl.dell.com).
M2 means a 2 mm nominal diameter with a 0.4 mm thread pitch. Imperial look-alike: #2-56 UNC (2.18 mm) is close but not interchangeable.
Dell Studio 1536 screw specifications
One row per fitment record. Head, drive are shown only where the source states them; pitch is the ISO coarse pitch for the thread.
| Thread | Length | Pitch | Head | Drive | Where it goes | Status |
|---|---|---|---|---|---|---|
| M2 | 3 mm | 0.4 mm | not stated | not stated | Unspecified (qty 1) | Confirmed |
| M3 | 3 mm | 0.5 mm | not stated | not stated | Hard drive (qty 4) | Confirmed |
Fitment records and sources
Unspecified (qty 1)
pitch 0.4 mm · tap 1.6 mm · clearance 2.4 mm · PH0 / Torx T6
Hard drive (qty 4)
pitch 0.5 mm · tap 2.5 mm · clearance 3.4 mm · PH1 / Torx T10
How to check the screw before you buy
- A screw that is even 1 mm too long in a laptop base can push into the keyboard, battery or a board trace, so match the length position by position.
- Diameter: across the threads an M2 screw measures about 2 mm with calipers (usually a hair under). This device also uses M3, so measure each screw rather than assuming they match.
- Pitch: 0.4 mm from one thread crest to the next (25 crests per centimetre). A thread pitch gauge or the pitch-gauge tool settles it in seconds.
- Length: measure from under the head to the tip for pan, button, wafer and cap heads; countersunk (flat) heads are measured overall.
- The record states 3 mm. Going longer risks bottoming out or touching parts behind the hole; going shorter loses thread engagement.
- Driver: the source does not name the drive. Standard M2 heads take PH0 for Phillips and T6 for Torx, and a 1.5 mm hex key for socket heads; a bit that fits loosely will cam out and strip the head.
- Tightening: no device-specific torque is published in these records. The site's general figure for M2 is about 25-40 N·cm into metal threads and 12-20 N·cm into plastic bosses; snug it up and stop.
Common mix-ups with M2 / M3
- The standard M.2 SSD screw is M2 x 3mm, but some laptops and handhelds use non-standard lengths or head shapes.
- M2 (2.00mm, 0.4mm pitch) is NOT the same as #2-56 UNC (2.18mm) — close enough to cross-thread and strip if forced.
- 3.5in desktop and enterprise hard drives are 6-32 UNC imperial, not M3 - only the 2.5in form factor is metric.
- Server drive caddy screws (Dell, HP) are usually M3 in very short lengths (3-4mm) because they bite into thin sheet metal — they are NOT the 6-32 UNC screws that go into the drive's own side holes.
Buy these screws at TechSpare Warehouse
In stock and shipped from South Carolina. Our black screws are Phillips wafer head (low profile); match the head style and length to the original before you order.
-
M2 x 3mm Screws for Dell XPS 13 9340 Base Cover SSD Shield 10-Pack Black
$4.99 -
10x M2 x 3mm Phillips Screws for Lenovo ThinkPad X131e Chromebook WiFi SSD
$4.99
-
M3 x 3mm Wafer Head Screws for Synology NAS Drive Canister 2.5 SSD Bay 10-Pack
$4.99 -
M3 x 3mm SSD Mounting Screws for HP Desktop 2.5 SATA Drive Replacement 10-Pack
$4.99 -
ASUS ROG Strix G15 G513R Replacement Screws Sold Individually – M1.6 x 3mm, M2 x 2.5mm, M2 x 3mm, M2.5 x 6mm Phillips Wafer Head, Black
$0.10Choose size -
ASUS ROG Strix G17 G713 Replacement Screws Sold Individually – M1.6 x 3mm, M2 x 2.5mm, M2 x 3mm, M2.5 x 6mm Phillips Wafer Head, Black
$0.10Choose size
-
Dell Inspiron 15 3520 Replacement Screws Sold Individually – M2 x 3mm, M2 x 5mm, M2.5 x 5mm, M3 x 3mm Phillips Wafer Head, Black
$0.10Choose size
-
M3 x 3mm Laptop HDD SSD Caddy Screws 2.5" SATA Hard Drive Mount Phillips
From $11.50Choose size
More in Laptops & PCs
2.5in drive trays & caddiesAcer / MSI laptopsAcer 5510/4020 series I/O and misc chassis screwsAcer 7520 / 7220Acer Aspire / Swift bottom coverAcer Aspire / Swift M.2 SSDAcer Aspire 1310Acer Aspire 1410Acer Aspire 1420PAcer Aspire 1650Acer Aspire 1680Acer Aspire 1690
Browse all 2799 in Laptops & PCs →The same screw also fits
Devices whose records share a thread with Dell Studio 1536, closest length match first.
- Lenovo ThinkPad X220 Tablet also M2 × 3 mm
- Dell Latitude D410 also M2 × 3 mm
- Lenovo N23 also M2 × 3 mm
- HP Pavilion DX6500 also M2 × 3 mm
- Lenovo Legion Y530-15ICH-1060 also M2 × 3 mm
- HP 350 G2 also M2 × 3 mm
- HP ProBook 4311s also M2 × 3 mm
- Dell Latitude 5540 also M2 × 3 mm
Questions about Dell Studio 1536 screws
- What size screw does Dell Studio 1536 use?
- M2 × 3 mm for unspecified (qty 1); M3 × 3 mm for hard drive (qty 4).
- How long are the screws in Dell Studio 1536?
- The record gives 3 mm. Measure the original from under the head (overall for a countersunk head) to confirm before ordering.
- What is the thread pitch of an M2 screw?
- 0.4 mm (coarse), which is the standard pitch for M2 machine screws; a 0.25 mm fine pitch exists but is uncommon. The tap drill is 1.6 mm and the normal clearance hole is 2.4 mm.
- What screwdriver do I need for Dell Studio 1536?
- The sources do not name the drive. For M2, Phillips heads normally take PH0 and Torx heads T6; socket heads take a 1.5 mm hex key.
- Can I use an imperial screw instead of M2?
- No. Imperial look-alike: #2-56 UNC (2.18 mm) is close but not interchangeable. Use a true M2 screw so it does not cross-thread or strip the hole.
- Where can I buy replacement screws for Dell Studio 1536?
- TechSpareWarehouse (our own store) lists M2 x 3mm and M3 x 3mm, which match lengths in the records above.