Dell Vostro 15 3583 screw size

Dell Vostro 15 3583 screw specifications

One row per fitment record. Head, drive are shown only where the source states them; pitch is the ISO coarse pitch for the thread.

How to check the screw before you buy

1. A screw that is even 1 mm too long in a laptop base can push into the keyboard, battery or a board trace, so match the length position by position.
2. Diameter: across the threads an M2 screw measures about 2 mm with calipers (usually a hair under). This device also uses M2.5 / M3, so measure each screw rather than assuming they match.
3. Pitch: 0.4 mm from one thread crest to the next (25 crests per centimetre). A thread pitch gauge or the pitch-gauge tool settles it in seconds.
4. Length: measure from under the head to the tip for pan, button, wafer and cap heads; countersunk (flat) heads are measured overall.
5. The records span 0.8–7 mm, which means different positions take different lengths — match each hole to its own screw.
6. Driver: the source does not name the drive. Standard M2 heads take PH0 for Phillips and T6 for Torx, and a 1.5 mm hex key for socket heads; a bit that fits loosely will cam out and strip the head.
7. Tightening: no device-specific torque is published in these records. The site's general figure for M2 is about 25-40 N·cm into metal threads and 12-20 N·cm into plastic bosses; snug it up and stop.

Pitch gauge · Screw size finder · Torque guide

More in Laptops & PCs

The same screw also fits

Devices whose records share a thread with Dell Vostro 15 3583, closest length match first.

• Framework Laptop 13 hinge-to-bottom-cover also M2 × 4 mm
• Lenovo IdeaPad S110 also M2 × 3 mm
• HP EliteBook 820 G1 also M2 × 2 mm
• Lenovo ThinkPad S440 also M2 × 2 mm
• HP Envy x360 16 inch 2-in-1 also M2 × 2 mm
• Lenovo YOGA 710-14IKB also M2 × 3 mm
• Lenovo ThinkPad R61i also M2 × 3 mm
• Dell Vostro 15 3580 also M2 × 0.8 mm

Questions about Dell Vostro 15 3583 screws

What size screw does Dell Vostro 15 3583 use?

M2 × 0.8 mm for SSD (qty 1); M2 × 2 mm for display (qty 4); M2 × 2 mm for hinge (qty 2); M2 × 2 mm for power button (qty 1, broadhead); M2 × 2 mm for SSD (qty 1, broadhead); M2 × 2 mm for touchpad (qty 6); M2 × 3 mm for battery (qty 4); M2 × 3 mm for DC-in (qty 1); M2 × 3 mm for hard drive (qty 4); M2 × 3 mm for heat sink (qty 4); M2 × 3 mm for SSD (qty 1); M2 × 3 mm for wireless card (qty 1); M2 × 4 mm for I/O board (qty 2); M2 × 4 mm for base cover (qty 1, captive); M2 × 4 mm for system board (qty 1); M2.5 × 2.5 mm for hinge (qty 8); M2.5 × 5 mm for fan (qty 3); M2.5 × 5 mm for hinge (qty 5); M2.5 × 7 mm for base cover (qty 6); M3 × 3 mm for hard drive (qty 4).

How long are the screws in Dell Vostro 15 3583?

The records range from 0.8 to 7 mm depending on the position, so match each screw to its own hole.

What is the thread pitch of an M2 screw?

0.4 mm (coarse), which is the standard pitch for M2 machine screws; a 0.25 mm fine pitch exists but is uncommon. The tap drill is 1.6 mm and the normal clearance hole is 2.4 mm.

What screwdriver do I need for Dell Vostro 15 3583?

The sources do not name the drive. For M2, Phillips heads normally take PH0 and Torx heads T6; socket heads take a 1.5 mm hex key.

Can I use an imperial screw instead of M2?

No. Imperial look-alike: #2-56 UNC (2.18 mm) is close but not interchangeable. Use a true M2 screw so it does not cross-thread or strip the hole.

Where can I buy replacement screws for Dell Vostro 15 3583?

TechSpareWarehouse (our own store) lists M2 x 2mm, M2 x 3mm and M2 x 4mm, which match lengths in the records above.