Dell XPS 13 9365 screw size

Dell XPS 13 9365 screw specifications

One row per fitment record. Head, drive are shown only where the source states them; pitch is the ISO coarse pitch for the thread.

How to check the screw before you buy

1. A screw that is even 1 mm too long in a laptop base can push into the keyboard, battery or a board trace, so match the length position by position.
2. Diameter: across the threads an M1.6 screw measures about 1.6 mm with calipers (usually a hair under). This device also uses M2 / M2.5, so measure each screw rather than assuming they match.
3. Pitch: 0.35 mm from one thread crest to the next (28.57 crests per centimetre). A thread pitch gauge or the pitch-gauge tool settles it in seconds.
4. Length: measure from under the head to the tip for pan, button, wafer and cap heads; countersunk (flat) heads are measured overall.
5. The records span 1.5–4 mm, which means different positions take different lengths — match each hole to its own screw.
6. Driver: the source names a Torx drive. For comparison, standard M1.6 heads take PH00 (Phillips) or T4–T5 (Torx), or a 1.5 mm hex key.
7. Tightening: no device-specific torque is published in these records. The site's general figure for M1.6 is about 12-20 N·cm into metal threads and 6-10 N·cm into plastic bosses; snug it up and stop.

Pitch gauge · Screw size finder · Torque guide

More in Laptops & PCs

The same screw also fits

Devices whose records share a thread with Dell XPS 13 9365, closest length match first.

• Dell Inspiron 15 5575 laptop also M2 × 2 mm
• Lenovo ThinkPad R52 also M2 × 3 mm
• HP Pavilion Widescreen ZT3000 also M2 × 3 mm
• Dell Latitude 5401 also M2 × 2 mm
• Dell Vostro 14 3430 also M2 × 2 mm
• Lenovo V110-15IAP also M2 × 3 mm
• Dell Inspiron 11 3179 2-in-1 also M2 × 2 mm
• Dell Alienware x16 R2 also M1.6 × 3 mm

Questions about Dell XPS 13 9365 screws

What size screw does Dell XPS 13 9365 use?

M1.6 × 1.5 mm for keyboard (qty 23); M1.6 × 1.5 mm for power button (qty 1); M1.6 × 2.5 mm for display (qty 2); M1.6 × 2.5 mm for hard drive (qty 2); M1.6 × 2.5 mm for system board (qty 7); M1.6 × 2.5 mm for unspecified (qty 2); M1.6 × 2.5 mm for wireless card (qty 1); M1.6 × 3 mm for display bezel (qty 6); M1.6 × 3 mm for hard drive (qty 2); M1.6 × 3 mm for SSD (qty 2); M1.6 × 3 mm for system board (qty 1); M1.6 × 4 mm for base cover (qty 1); M1.6 × 4 mm for battery (qty 2); M2 × 2 mm for keyboard (qty 6); M2 × 2 mm for speaker (qty 4); M2 × 2 mm for touchpad (qty 2); M2 × 3 mm for base cover (qty 8, Torx); M2 × 3 mm for battery (qty 6); M2 × 3 mm for unspecified (qty 2); M2.5 × 3.5 mm for .

How long are the screws in Dell XPS 13 9365?

The records range from 1.5 to 4 mm depending on the position, so match each screw to its own hole.

What is the thread pitch of an M1.6 screw?

0.35 mm (coarse), which is the standard pitch for M1.6 machine screws; a 0.2 mm fine pitch exists but is uncommon. The tap drill is 1.25 mm and the normal clearance hole is 1.8 mm.

What screwdriver do I need for Dell XPS 13 9365?

The source lists a Torx drive. Standard M1.6 heads otherwise take PH00 (Phillips) or T4–T5 (Torx), or a 1.5 mm hex key.

Can I use an imperial screw instead of M1.6?

No. Imperial look-alike: #1-72 UNF (1.85 mm) is larger; there is no true imperial equivalent. Use a true M1.6 screw so it does not cross-thread or strip the hole.

Where can I buy replacement screws for Dell XPS 13 9365?

TechSpareWarehouse (our own store) lists M1.6 x 3mm, M1.6 x 4mm and M2 x 2mm, which match lengths in the records above.