Dell XPS 15 9570 screw size

Dell XPS 15 9570 screw specifications

One row per fitment record. Head, drive are shown only where the source states them; pitch is the ISO coarse pitch for the thread.

How to check the screw before you buy

1. A screw that is even 1 mm too long in a laptop base can push into the keyboard, battery or a board trace, so match the length position by position.
2. Diameter: across the threads an M1.6 screw measures about 1.6 mm with calipers (usually a hair under). This device also uses M2 / M2.5, so measure each screw rather than assuming they match.
3. Pitch: 0.35 mm from one thread crest to the next (28.57 crests per centimetre). A thread pitch gauge or the pitch-gauge tool settles it in seconds.
4. Length: measure from under the head to the tip for pan, button, wafer and cap heads; countersunk (flat) heads are measured overall.
5. The records span 1.5–8.5 mm, which means different positions take different lengths — match each hole to its own screw.
6. Driver: the source names a Torx T5 drive. For comparison, standard M1.6 heads take PH00 (Phillips) or T4–T5 (Torx), or a 1.5 mm hex key.
7. Tightening: no device-specific torque is published in these records. The site's general figure for M1.6 is about 12-20 N·cm into metal threads and 6-10 N·cm into plastic bosses; snug it up and stop.

Pitch gauge · Screw size finder · Torque guide

More in Laptops & PCs

The same screw also fits

Devices whose records share a thread with Dell XPS 15 9570, closest length match first.

• Lenovo 100e 2nd Gen also M2 × 3 mm
• HP EliteBook 850 G1 also M2 × 2 mm
• Lenovo ideapad 300-14ISK also M2 × 3 mm
• Acer TravelMate 6293 also M2 × 4 mm
• Dell Latitude 5500 also M2 × 2 mm
• Lenovo YOGA 710-14ISK also M2 × 3 mm
• Lenovo ThinkPad T14 Gen 1 also M2 × 2 mm
• HP mt43 Mobile Thin Client also M2 × 2 mm

Questions about Dell XPS 15 9570 screws

What size screw does Dell XPS 15 9570 use?

M1.6 × 1.5 mm for keyboard (qty 31); M1.6 × 1.5 mm for power button (qty 1); M1.6 × 3 mm for power button (qty 2); M2 × 2 mm for display (qty 2); M2 × 2 mm for speaker (qty 4); M2 × 2 mm for SSD (qty 1); M2 × 3 mm for base cover (qty 10, Torx T5); M2 × 3 mm for DC-in (qty 1); M2 × 3 mm for heat sink (qty 5); M2 × 3 mm for SSD (qty 1); M2 × 3 mm for unspecified (qty 4); M2 × 4 mm for battery (qty 7); M2 × 4 mm for display (qty 2); M2 × 4 mm for fan (qty 4); M2 × 4 mm for hard drive (qty 4); M2 × 4 mm for system board (qty 5); M2 × 4 mm for unspecified (qty 4); M2 × 4 mm for wireless card (qty 4); M2 × 8 mm for base cover (qty 2); M2 × 8.5 mm for base cover (qty 2); M2.5 × 5 mm for display (qt.

How long are the screws in Dell XPS 15 9570?

The records range from 1.5 to 8.5 mm depending on the position, so match each screw to its own hole.

What is the thread pitch of an M1.6 screw?

0.35 mm (coarse), which is the standard pitch for M1.6 machine screws; a 0.2 mm fine pitch exists but is uncommon. The tap drill is 1.25 mm and the normal clearance hole is 1.8 mm.

What screwdriver do I need for Dell XPS 15 9570?

The source lists a Torx T5 drive. Standard M1.6 heads otherwise take PH00 (Phillips) or T4–T5 (Torx), or a 1.5 mm hex key.

Can I use an imperial screw instead of M1.6?

No. Imperial look-alike: #1-72 UNF (1.85 mm) is larger; there is no true imperial equivalent. Use a true M1.6 screw so it does not cross-thread or strip the hole.

Where can I buy replacement screws for Dell XPS 15 9570?

TechSpareWarehouse (our own store) lists M1.6 x 3mm, M2 x 2mm and M2 x 3mm, which match lengths in the records above.