DJI Agras Agras T50/T25/T16/T20/T30 and FlyCart 30 airframe screw screw size
M3 · 8 mm long
The screws used on DJI Agras Agras T50/T25/T16/T20/T30 and FlyCart 30 airframe screw are M3, 8 mm long.
It is listed for genuine spare part YC.WJ.LL000215, black screw with washer.
This entry is marked confirmed and comes from droneroboticstec.com.
For reference, M3 is 3 mm across the threads at 0.5 mm pitch. The imperial size people confuse it with: #5-40 (3.18 mm) or #4-40 — neither interchanges with M3.
DJI Agras Agras T50/T25/T16/T20/T30 and FlyCart 30 airframe screw screw specifications
One row per fitment record. Head, drive are shown only where the source states them; pitch is the ISO coarse pitch for the thread.
| Thread | Length | Pitch | Head | Drive | Where it goes | Status |
|---|---|---|---|---|---|---|
| M3 | 8 mm | 0.5 mm | not stated | not stated | Genuine spare part YC.WJ.LL000215, black screw with washerblack finish, washer / flange face | Confirmed |
Fitment records and sources
Genuine spare part YC.WJ.LL000215, black screw with washer
pitch 0.5 mm · tap 2.5 mm · clearance 3.4 mm · PH1 / Torx T10
How to check the screw before you buy
- Vibration loosens small screws on drones and RC models, so builders commonly add a drop of medium (blue) threadlocker on metal-to-metal joints — never on plastic.
- Diameter: across the threads an M3 screw measures about 3 mm with calipers (usually a hair under). If yours measures noticeably more or less, it is a different thread.
- Pitch: 0.5 mm from one thread crest to the next (20 crests per centimetre). A thread pitch gauge or the pitch-gauge tool settles it in seconds.
- Length: measure from under the head to the tip for pan, button, wafer and cap heads; countersunk (flat) heads are measured overall.
- The record states 8 mm. Going longer risks bottoming out or touching parts behind the hole; going shorter loses thread engagement.
- Driver: the source does not name the drive. Standard M3 heads take PH1 for Phillips and T10 for Torx, and a 2.5 mm hex key for socket heads; a bit that fits loosely will cam out and strip the head.
- Tightening: no device-specific torque is published in these records. The site's general figure for M3 is about 80-130 N·cm into metal threads and 35-60 N·cm into plastic bosses; snug it up and stop.
Common mix-ups with M3
- Many gas-detector and sensor manuals only give a torque spec (e.g. '0.5 N·m max') without repeating the thread size at every mention — the explicit M3 callout is usually only in the accessories/spare-parts table, not the main installation steps.
- M3 (3.0mm, 0.5mm pitch) is not #6-32 UNC (~3.5mm) — they look identical and cross-thread, the single most common PC-building mistake.
Buy these screws at TechSpare Warehouse
In stock and shipped from South Carolina. Our black screws are Phillips wafer head (low profile); match the head style and length to the original before you order.
-
M3 x 8mm Screws for Leather Spike Attachments Guitar Straps 10-Pack
$4.99 -
M3 x 8mm Phillips Wafer Head Screw for SLA Resin 3D Printer VAT Film - Single Replacement Black
$0.10 each · min. 50
-
M3 x 8mm Phillips Flat Head Countersunk Machine Screws Zinc Silver 100-Pack for RC & 3D Printers
$9.99 -
M3 x 8mm Phillips Flat Head Countersunk Machine Screws Zinc Silver 10-Pack for RC & 3D Printers
$4.99
More in Drones, RC & Gimbals
1/10 scale RC cars1/8 scale RC car chassis hardware3D-printed FPV stack mounts and spacers5-inch brushless motor to armAirsoft V2 / EHPA gearbox shellsALware Quad Flyer Spider 500 quadcopter kitAntique wall clock pendulum bracketsArcade marquee retainersARRMA Senton (and similar 1/10 vehicles)ARRMA Senton/kingpin-equipped vehiclesAxial Racing crawler/buggy kitsAxial SCX10 III RC crawler chassis
Browse all 144 in Drones, RC & Gimbals →The same screw also fits
Devices whose records share a thread with DJI Agras Agras T50/T25/T16/T20/T30 and FlyCart 30 airframe screw, closest length match first.
- REV Robotics T-slot extrusion screw (41-1907) also M3 × 8 mm
- 5-inch brushless motor to arm also M3 × 8 mm
- 1/10 scale RC cars also M3 × 8 mm
- Nerf blaster thumbscrews (mid sizes) also M3 × 8 mm
- FPV flight controller stack 30.5x30.5mm also M3 × 8 mm
- FPV drone motors (5-inch class) also M3 × 8 mm
- RC brushless motor mounts also M3 × 8 mm
- ALware Quad Flyer Spider 500 quadcopter kit also M3 × 8 mm
Questions about DJI Agras Agras T50/T25/T16/T20/T30 and FlyCart 30 airframe screw screws
- What size screw does DJI Agras Agras T50/T25/T16/T20/T30 and FlyCart 30 airframe screw use?
- M3 × 8 mm for genuine spare part YC.WJ.LL000215, black screw with washer.
- How long are the screws in DJI Agras Agras T50/T25/T16/T20/T30 and FlyCart 30 airframe screw?
- The record gives 8 mm. Measure the original from under the head (overall for a countersunk head) to confirm before ordering.
- What is the thread pitch of an M3 screw?
- 0.5 mm (coarse), which is the standard pitch for M3 machine screws; a 0.35 mm fine pitch exists but is uncommon. The tap drill is 2.5 mm and the normal clearance hole is 3.4 mm.
- What screwdriver do I need for DJI Agras Agras T50/T25/T16/T20/T30 and FlyCart 30 airframe screw?
- The sources do not name the drive. For M3, Phillips heads normally take PH1 and Torx heads T10; socket heads take a 2.5 mm hex key.
- Can I use an imperial screw instead of M3?
- No. Imperial look-alike: #5-40 (3.18 mm) or #4-40 — neither interchanges with M3. Use a true M3 screw so it does not cross-thread or strip the hole.
- Where can I buy replacement screws for DJI Agras Agras T50/T25/T16/T20/T30 and FlyCart 30 airframe screw?
- TechSpareWarehouse (our own store) lists M3 x 8mm, which matches the length in the records above.