How long are the screws in DJI Mavic Pro gimbal/camera mounting screws?

The record gives 3 mm. Measure the original from under the head (overall for a countersunk head) to confirm before ordering.

What is the thread pitch of an M2 screw?

0.4 mm (coarse), which is the standard pitch for M2 machine screws; a 0.25 mm fine pitch exists but is uncommon. The tap drill is 1.6 mm and the normal clearance hole is 2.4 mm.

What screwdriver do I need for DJI Mavic Pro gimbal/camera mounting screws?

The sources do not name the drive. For M2, Phillips heads normally take PH0 and Torx heads T6; socket heads take a 1.5 mm hex key.

Can I use an imperial screw instead of M2?

No. Imperial look-alike: #2-56 UNC (2.18 mm) is close but not interchangeable. Use a true M2 screw so it does not cross-thread or strip the hole.

Where can I buy replacement screws for DJI Mavic Pro gimbal/camera mounting screws?

TechSpareWarehouse (our own store) lists M2 x 3mm, which matches the length in the records above.

DJI Mavic Pro gimbal/camera mounting screws screw size

M2 · 3 mm long

The screws used on DJI Mavic Pro gimbal/camera mounting screws are M2, 3 mm long.

Where it is used: iFixit repair guide for gimbal/camera replacement documents multiple small screw sizes; DJI Mavic Pro gimbal frame screws are commonly specified in third-party screw kits as M1.4/M2 metric fasteners for the yaw/roll/pitch arms.

This entry is marked likely and comes from ifixit.com.

For reference, M2 is 2 mm across the threads at 0.4 mm pitch. The imperial size people confuse it with: #2-56 UNC (2.18 mm) is close but not interchangeable.

DJI Mavic Pro gimbal/camera mounting screws screw specifications

One row per fitment record. Head, drive are shown only where the source states them; pitch is the ISO coarse pitch for the thread.

Thread	Length	Pitch	Head	Drive	Where it goes	Status
M2	3 mm	0.4 mm	not stated	not stated	iFixit repair guide for gimbal/camera replacement documents multiple small screw sizes; DJI Mavic Pro gimbal frame screws are commonly specified in third-party screw kits as M1.4/M2 metric fasteners for the yaw/roll/pitch arms	Likely

Fitment records and sources

M2M1.4x3, M2x3likely

iFixit repair guide for gimbal/camera replacement documents multiple small screw sizes; DJI Mavic Pro gimbal frame screws are commonly specified in third-party screw kits as M1.4/M2 metric fasteners for the yaw/roll/pitch arms

pitch 0.4 mm · tap 1.6 mm · clearance 2.4 mm · PH0 / Torx T6

Source

How to check the screw before you buy

Camera and optics hardware often uses short screws into thin threaded plates, so check engagement before tightening fully.
Diameter: across the threads an M2 screw measures about 2 mm with calipers (usually a hair under). If yours measures noticeably more or less, it is a different thread.
Pitch: 0.4 mm from one thread crest to the next (25 crests per centimetre). A thread pitch gauge or the pitch-gauge tool settles it in seconds.
Length: measure from under the head to the tip for pan, button, wafer and cap heads; countersunk (flat) heads are measured overall.
The record states 3 mm. Going longer risks bottoming out or touching parts behind the hole; going shorter loses thread engagement.
Driver: the source does not name the drive. Standard M2 heads take PH0 for Phillips and T6 for Torx, and a 1.5 mm hex key for socket heads; a bit that fits loosely will cam out and strip the head.
Tightening: no device-specific torque is published in these records. The site's general figure for M2 is about 25-40 N·cm into metal threads and 12-20 N·cm into plastic bosses; snug it up and stop.

Common mix-ups with M2

'M2x3 T5' is commonly conflated with the Torx bit size (T5) — the T5 refers to the drive, M2x3 is the actual metric thread and length.
M.2 SSD mounting screws (M2 x 3mm) are frequently mislabeled generically as 'M.2 screws' which can be confused with the M2 metric thread designation — they do coincide numerically here but are conceptually distinct (M.2 = card format, M2 = thread size).

Pitch gauge · Screw size finder · Torque guide

Buy these screws at TechSpare Warehouse

In stock and shipped from South Carolina. Our black screws are Phillips wafer head (low profile); match the head style and length to the original before you order.

More in Cameras & Optics

1.25" eyepiece/diagonal/SCT visual back thumb screw Aimpoint Comp M4 / M4s LRP & TNP mount Aimpoint Micro T-1/T-2/H-1/H-2 standard mount Aimpoint Micro T-1/T-2/H-1/H-2 standard mount screw Aimpoint SM-2001/2007 Micro T1/T2 mount Airsoft red dot sight mounting screw set (Laylax/Quintes Sence)Airsoft/firearm red-dot sight optic mounting screws (Vortex Viper, Swampfox patterns)Alpine and touring ski bindings (Binding Freedom inserts)Arca-style quick-release plate ARRI plate for Sony VENICE 1/2 Artesky 340mm Vixen Dovetail Bar Astromania finder scope dovetail base

Browse all 278 in Cameras & Optics →

The same screw also fits

Devices whose records share a thread with DJI Mavic Pro gimbal/camera mounting screws, closest length match first.

Riflescope turret cap also M2 × 3 mm
Webcam lens housing and board also M2 × 3 mm
Olympus BH-PRE microscope nosepiece also M2 × 3 mm
Olympus BH-2 / BH2-5RE microscope nosepiece also M2 × 3 mm
Eyeglass frame screw (largest ISO spectacle size) also M2 × 3 mm
Camera lens focus ring set screw also M2 × 3 mm
Lenovo ideapad 330R-14AST also M2 × 3 mm
Lenovo ideapad 320S-15ABR also M2 × 3 mm

Questions about DJI Mavic Pro gimbal/camera mounting screws screws

What size screw does DJI Mavic Pro gimbal/camera mounting screws use?: M2 × 3 mm for iFixit repair guide for gimbal/camera replacement documents multiple small screw sizes; DJI Mavic Pro gimbal frame screws are commonly specified in third-party screw kits as M1.4/M2 metric fasteners for the yaw/roll/pitch arms.
How long are the screws in DJI Mavic Pro gimbal/camera mounting screws?: The record gives 3 mm. Measure the original from under the head (overall for a countersunk head) to confirm before ordering.
What is the thread pitch of an M2 screw?: 0.4 mm (coarse), which is the standard pitch for M2 machine screws; a 0.25 mm fine pitch exists but is uncommon. The tap drill is 1.6 mm and the normal clearance hole is 2.4 mm.
What screwdriver do I need for DJI Mavic Pro gimbal/camera mounting screws?: The sources do not name the drive. For M2, Phillips heads normally take PH0 and Torx heads T6; socket heads take a 1.5 mm hex key.
Can I use an imperial screw instead of M2?: No. Imperial look-alike: #2-56 UNC (2.18 mm) is close but not interchangeable. Use a true M2 screw so it does not cross-thread or strip the hole.
Where can I buy replacement screws for DJI Mavic Pro gimbal/camera mounting screws?: TechSpareWarehouse (our own store) lists M2 x 3mm, which matches the length in the records above.

Heads up: shipping delay