Drip coffee machine housing screw size
M4 · 10 to 16 mm long
Our records put Drip coffee machine housing on M4 screws in lengths from 10 to 16 mm.
The record covers holds the outer plastic panels together.
This entry is marked reported and comes from ifixit.com.
M4 means a 4 mm nominal diameter with a 0.7 mm thread pitch. Imperial look-alike: #8-32 (4.17 mm) — the standard US PC/rack screw, close but not the same.
Drip coffee machine housing screw specifications
One row per fitment record. Head, drive are shown only where the source states them; pitch is the ISO coarse pitch for the thread.
| Thread | Length | Pitch | Head | Drive | Where it goes | Status |
|---|---|---|---|---|---|---|
| M4 | 10–16 mm | 0.7 mm | not stated | not stated | holds the outer plastic panels together | Reported |
Fitment records and sources
holds the outer plastic panels together
pitch 0.7 mm · tap 3.3 mm · clearance 4.5 mm · PH2 / Torx T20
How to check the screw before you buy
- Unplug the appliance and discharge any capacitors before removing covers.
- Diameter: across the threads an M4 screw measures about 4 mm with calipers (usually a hair under). If yours measures noticeably more or less, it is a different thread.
- Pitch: 0.7 mm from one thread crest to the next (14.29 crests per centimetre). A thread pitch gauge or the pitch-gauge tool settles it in seconds.
- Length: measure from under the head to the tip for pan, button, wafer and cap heads; countersunk (flat) heads are measured overall.
- The records span 10–16 mm, which means different positions take different lengths — match each hole to its own screw.
- Driver: the source does not name the drive. Standard M4 heads take PH2 for Phillips and T20 for Torx, and a 3 mm hex key for socket heads; a bit that fits loosely will cam out and strip the head.
- Tightening: no device-specific torque is published in these records. The site's general figure for M4 is about 2.0-3.0 N·m into metal threads and 0.8-1.4 N·m into plastic bosses; snug it up and stop.
Common mix-ups with M4
- Most HVAC chassis hardware in US-market units is imperial; metric shows up mainly on European-made components.
- Bopla SHR-Z boss screws and Hammond 1591XXF screws look metric but are self-tapping/imperial — don't substitute a machine screw into those bosses.
Buy these screws at TechSpare Warehouse
In stock and shipped from South Carolina. Our black screws are Phillips wafer head (low profile); match the head style and length to the original before you order.
-
M4 x 12mm Black Wafer Head Chainsaw & Cut-off Saw Screws for STIHL MS 460, MS 362, TS480i & TS500i (IS-M4x12) – 10-Pack Replacement
$5.49Choose size -
M4 x 12mm Black Wafer Head Monitor VESA, Neck & Stand Screws for Dell UltraSharp U4320Q & Sceptre Monitors – 8-Pack Replacement
$5.49Choose size -
M4 x 10mm Black Wafer Head Charging Port Screws for GOTRAX G3, G4, GMAX & GMAX Ultra – 10-Pack Replacement
$5.49Choose size -
M4 x 10mm Black Wafer Head Fender Clamp Base Screws for Minoura KODACHI DYK-1R Rear Fender – 8-Pack Replacement
$5.49Choose size
More in Appliances & HVAC
Appliance door hingesAppliance handlesAstoria/CMA espresso solenoid group head (used in coffee kiosk equipment)Astoria/CMA espresso solenoid group head screwBerkel 330M Slicer cover fastenerBerkel 330M Slicer sharpener/guard mountingBezzera Giulia espresso machineBosch dishwasherCoffee machine control panelDaikin FTXS/CTXS Mini-split control board / cover screwDaikin FTXS/CTXS Mini-split indoor unit mounting / terminal cover screwDaikin FTXS/CTXS Mini-split indoor unit terminal cover / mounting plate screw
Browse all 62 in Appliances & HVAC →The same screw also fits
Devices whose records share a thread with Drip coffee machine housing, closest length match first.
- Daikin FTXS/CTXS Mini-split indoor unit mounting / terminal cover screw also M4 × 12 mm
- Samsung dishwasher also M4 × 12 mm
- Espresso machine group head also M4 × 10–16 mm
- Dyson vacuum motor housing also M4 × 10–16 mm
- Furrion RV appliance trim kit hardware also M4 × 10 mm
- Johnson Controls PENN VFD68 Variable Frequency Drive (used on pumps, mixers, HVAC/water treatment motors) also M4 × 10 mm
- Microwave housing and control panel also M4 × 10–14 mm
- Samsung dishwasher panels and frame also M4 × 12 mm
Questions about Drip coffee machine housing screws
- What size screw does Drip coffee machine housing use?
- M4 × 10–16 mm for holds the outer plastic panels together.
- How long are the screws in Drip coffee machine housing?
- The records range from 10 to 16 mm depending on the position, so match each screw to its own hole.
- What is the thread pitch of an M4 screw?
- 0.7 mm (coarse), which is the standard pitch for M4 machine screws; a 0.5 mm fine pitch exists but is uncommon. The tap drill is 3.3 mm and the normal clearance hole is 4.5 mm.
- What screwdriver do I need for Drip coffee machine housing?
- The sources do not name the drive. For M4, Phillips heads normally take PH2 and Torx heads T20; socket heads take a 3 mm hex key.
- Can I use an imperial screw instead of M4?
- No. Imperial look-alike: #8-32 (4.17 mm) — the standard US PC/rack screw, close but not the same. Use a true M4 screw so it does not cross-thread or strip the hole.