Edmund Optics metric post kit screw size
M4 · length not stated in the sources
The screws used on Edmund Optics metric post kit are M4. None of the sources we found gives an exact length, so measure the original before you order.
Where it is used: post kit supplied with an M4 mounting stud.
This entry is marked confirmed and comes from edmundoptics.co.uk.
An M4 screw is 4 mm in diameter with a 0.7 mm pitch, tapped with a 3.3 mm drill; imperial look-alike: #8-32 (4.17 mm) — the standard US PC/rack screw, close but not the same.
Edmund Optics metric post kit screw specifications
One row per fitment record. Head, drive are shown only where the source states them; pitch is the ISO coarse pitch for the thread.
| Thread | Length | Pitch | Head | Drive | Where it goes | Status |
|---|---|---|---|---|---|---|
| M4 | not stated | 0.7 mm | not stated | not stated | Post kit supplied with an M4 mounting stud | Confirmed |
Fitment records and sources
Post kit supplied with an M4 mounting stud
pitch 0.7 mm · tap 3.3 mm · clearance 4.5 mm · PH2 / Torx T20
How to check the screw before you buy
- Camera and optics hardware often uses short screws into thin threaded plates, so check engagement before tightening fully.
- Diameter: across the threads an M4 screw measures about 4 mm with calipers (usually a hair under). If yours measures noticeably more or less, it is a different thread.
- Pitch: 0.7 mm from one thread crest to the next (14.29 crests per centimetre). A thread pitch gauge or the pitch-gauge tool settles it in seconds.
- Length: measure from under the head to the tip for pan, button, wafer and cap heads; countersunk (flat) heads are measured overall.
- Driver: the source does not name the drive. Standard M4 heads take PH2 for Phillips and T20 for Torx, and a 3 mm hex key for socket heads; a bit that fits loosely will cam out and strip the head.
- Tightening: no device-specific torque is published in these records. The site's general figure for M4 is about 2.0-3.0 N·m into metal threads and 0.8-1.4 N·m into plastic bosses; snug it up and stop.
Common mix-ups with M4
- Standard injection-molded LEGO Technic axles/pins are friction-fit, not threaded; only specialty metal aftermarket axle replacements use real ISO metric threads (M4/M5), and these are not official LEGO parts.
- Most HVAC chassis hardware in US-market units is imperial; metric shows up mainly on European-made components.
More in Cameras & Optics
1.25" eyepiece/diagonal/SCT visual back thumb screwAimpoint Comp M4 / M4s LRP & TNP mountAimpoint Micro T-1/T-2/H-1/H-2 standard mountAimpoint Micro T-1/T-2/H-1/H-2 standard mount screwAimpoint SM-2001/2007 Micro T1/T2 mountAirsoft red dot sight mounting screw set (Laylax/Quintes Sence)Airsoft/firearm red-dot sight optic mounting screws (Vortex Viper, Swampfox patterns)Alpine and touring ski bindings (Binding Freedom inserts)Arca-style quick-release plateARRI plate for Sony VENICE 1/2Artesky 340mm Vixen Dovetail BarAstromania finder scope dovetail base
Browse all 278 in Cameras & Optics →The same screw also fits
Devices whose records share a thread with Edmund Optics metric post kit, closest length match first.
- Gimbal stabilizer arm clamp also M4
- i-PRO / Panasonic WV-QWL100 camera mount bracket also M4
- Newport M-SP-2 optical post also M4
- Vivotek IT9360-H / IT9380-H dome camera also M4
- OpenFlexure Delta Stage frame also M4
- Optic/scope ring mounting screw manufactured to engineering drawing (fastener supplier drawing, generic optics mount hardware) also M4
- Celestron NexStar 8 eyepiece holder also M4
- Thorlabs ELL21/M rotation mount also M4
Questions about Edmund Optics metric post kit screws
- What size screw does Edmund Optics metric post kit use?
- M4 for post kit supplied with an M4 mounting stud.
- How long are the screws in Edmund Optics metric post kit?
- None of the sources states a length. Remove one screw and measure it from under the head to the tip (overall for a countersunk head).
- What is the thread pitch of an M4 screw?
- 0.7 mm (coarse), which is the standard pitch for M4 machine screws; a 0.5 mm fine pitch exists but is uncommon. The tap drill is 3.3 mm and the normal clearance hole is 4.5 mm.
- What screwdriver do I need for Edmund Optics metric post kit?
- The sources do not name the drive. For M4, Phillips heads normally take PH2 and Torx heads T20; socket heads take a 3 mm hex key.
- Can I use an imperial screw instead of M4?
- No. Imperial look-alike: #8-32 (4.17 mm) — the standard US PC/rack screw, close but not the same. Use a true M4 screw so it does not cross-thread or strip the hole.