Electrolux Professional compact rack-type dishwasher screw size
M3 / M4 / M5 / M6 · 5 to 50 mm long
If you are replacing a screw on Electrolux Professional compact rack-type dishwasher, the thread is M3, M4, M5 and M6 in lengths from 5 to 50 mm.
There are 4 separate fitment records for it, including conveyor drive motor mounting listed as M3 in the spare parts catalogue (M3), magnet, guard and door screws supplied as M4 x 10mm sets (M4) and M5 x 5mm and M5 x 10mm screws plus M5 door spring bracket nut (M5), plus 1 more in the table below.
4 of the 4 records are marked confirmed, drawn from 1 source (buy.electroluxprofessional.com).
An M3 screw is 3 mm in diameter with a 0.5 mm pitch, tapped with a 2.5 mm drill; imperial look-alike: #5-40 (3.18 mm) or #4-40 — neither interchanges with M3.
Electrolux Professional compact rack-type dishwasher screw specifications
One row per fitment record. Head, drive are shown only where the source states them; pitch is the ISO coarse pitch for the thread.
| Thread | Length | Pitch | Head | Drive | Where it goes | Status |
|---|---|---|---|---|---|---|
| M3 | not stated | 0.5 mm | not stated | not stated | Conveyor drive motor mounting listed as M3 in the spare parts catalogue | Confirmed |
| M4 | 10 mm | 0.7 mm | not stated | not stated | Magnet, guard and door screws supplied as M4 x 10mm sets | Confirmed |
| M5 | 5–10 mm | 0.8 mm | not stated | not stated | M5 x 5mm and M5 x 10mm screws plus M5 door spring bracket nut | Confirmed |
| M6 | 14–50 mm | 1 mm | not stated | not stated | M6 x 14mm and M6 x 50mm fastener sets in the spare parts catalogue | Confirmed |
Fitment records and sources
Conveyor drive motor mounting listed as M3 in the spare parts catalogue
pitch 0.5 mm · tap 2.5 mm · clearance 3.4 mm · PH1 / Torx T10
Magnet, guard and door screws supplied as M4 x 10mm sets
pitch 0.7 mm · tap 3.3 mm · clearance 4.5 mm · PH2 / Torx T20
M5 x 5mm and M5 x 10mm screws plus M5 door spring bracket nut
pitch 0.8 mm · tap 4.2 mm · clearance 5.5 mm · PH2 / Torx T25
M6 x 14mm and M6 x 50mm fastener sets in the spare parts catalogue
pitch 1 mm · tap 5 mm · clearance 6.6 mm · PH3 / Torx T30
How to check the screw before you buy
- Board standoffs and enclosure bosses set the usable length: the screw should clamp the board without bottoming in the standoff.
- Diameter: across the threads an M3 screw measures about 3 mm with calipers (usually a hair under). This device also uses M4 / M5 / M6, so measure each screw rather than assuming they match.
- Pitch: 0.5 mm from one thread crest to the next (20 crests per centimetre). A thread pitch gauge or the pitch-gauge tool settles it in seconds.
- Length: measure from under the head to the tip for pan, button, wafer and cap heads; countersunk (flat) heads are measured overall.
- The records span 5–50 mm, which means different positions take different lengths — match each hole to its own screw.
- Driver: the source does not name the drive. Standard M3 heads take PH1 for Phillips and T10 for Torx, and a 2.5 mm hex key for socket heads; a bit that fits loosely will cam out and strip the head.
- Tightening: no device-specific torque is published in these records. The site's general figure for M3 is about 80-130 N·cm into metal threads and 35-60 N·cm into plastic bosses; snug it up and stop.
Common mix-ups with M3 / M4 / M5 / M6
- M3 is by far the most common metric fastener across lab, metrology, and cleanroom equipment, spanning coarse-thread ISO M3x0.5 in most cases.
- Some rackmount KVM switch kits pair M4x10 bracket-to-rack screws with M3.2x4.5 bracket-to-chassis screws (non-standard M3.2, not a true M3), so kits are not fully interchangeable with generic M3/M4 hardware.
- Stacking frame + rack tab + fender stay needs 18-20mm bolts, not the 12-16mm that come with a cage.
- Rack hole threads vary: 10-32 and 12-24 are still common in US racks alongside M6 - check the rail before buying.
Buy these screws at TechSpare Warehouse
In stock and shipped from South Carolina. Our black screws are Phillips wafer head (low profile); match the head style and length to the original before you order.
-
M4 x 10mm Black Wafer Head Charging Port Screws for GOTRAX G3, G4, GMAX & GMAX Ultra – 10-Pack Replacement
$5.49Choose size -
M4 x 10mm Black Wafer Head Fender Clamp Base Screws for Minoura KODACHI DYK-1R Rear Fender – 8-Pack Replacement
$5.49Choose size -
M5 x 10mm Black Wafer Head Bike Fender & Rack Screws for Tern MTR Fenders, Blackburn EX-1 Rack, ENVO Stax & René Herse Fender Set – 10-Pack Replacement
$5.99Choose size -
M5 x 10mm Black Wafer Head Folding Mechanism Screws for GOTRAX GXL V2, Rival, XR Ultra & XR Elite – 10-Pack Replacement
$5.99Choose size
More in Electronics, Racks & Enclosures
The same screw also fits
Devices whose records share a thread with Electrolux Professional compact rack-type dishwasher, closest length match first.
- 19-inch rack cage nut (metric square-hole rails) also M6 × 14–16 mm
- Power wheelchair drive motor mounts also M6 × 16–30 mm
- Weidmueller BFSC busbar/DIN-rail screw accessory also M5 × 8 mm
- Thule ProRide 591/598 Bike Rack also M6 × 35 mm
- Whirlpool front-load washer electronic control board mounting screws also M4 × 10 mm
- Yamaha F25 / T25 outboard motor also M6 × 18–35 mm
- Large soundbars & subwoofers also M6 × 14–20 mm
- DIN rail clips and enclosure brackets also M4 × 10 mm
Questions about Electrolux Professional compact rack-type dishwasher screws
- What size screw does Electrolux Professional compact rack-type dishwasher use?
- M3 for conveyor drive motor mounting listed as M3 in the spare parts catalogue; M4 × 10 mm for magnet, guard and door screws supplied as M4 x 10mm sets; M5 × 5–10 mm for M5 x 5mm and M5 x 10mm screws plus M5 door spring bracket nut; M6 × 14–50 mm for M6 x 14mm and M6 x 50mm fastener sets in the spare parts catalogue.
- How long are the screws in Electrolux Professional compact rack-type dishwasher?
- The records range from 5 to 50 mm depending on the position, so match each screw to its own hole.
- What is the thread pitch of an M3 screw?
- 0.5 mm (coarse), which is the standard pitch for M3 machine screws; a 0.35 mm fine pitch exists but is uncommon. The tap drill is 2.5 mm and the normal clearance hole is 3.4 mm.
- What screwdriver do I need for Electrolux Professional compact rack-type dishwasher?
- The sources do not name the drive. For M3, Phillips heads normally take PH1 and Torx heads T10; socket heads take a 2.5 mm hex key.
- Can I use an imperial screw instead of M3?
- No. Imperial look-alike: #5-40 (3.18 mm) or #4-40 — neither interchanges with M3. Use a true M3 screw so it does not cross-thread or strip the hole.