What size screw does Elo EMV bracket assembly special pan-head screw use?

M3 × 8 mm for verifone/Ingenico kits; SCREW_M3X8_SPECIAL.

How long are the screws in Elo EMV bracket assembly special pan-head screw?

The record gives 8 mm. Measure the original from under the head (overall for a countersunk head) to confirm before ordering.

What is the thread pitch of an M3 screw?

0.5 mm (coarse), which is the standard pitch for M3 machine screws; a 0.35 mm fine pitch exists but is uncommon. The tap drill is 2.5 mm and the normal clearance hole is 3.4 mm.

What screwdriver do I need for Elo EMV bracket assembly special pan-head screw?

The sources do not name the drive. For M3, Phillips heads normally take PH1 and Torx heads T10; socket heads take a 2.5 mm hex key.

Can I use an imperial screw instead of M3?

No. Imperial look-alike: #5-40 (3.18 mm) or #4-40 — neither interchanges with M3. Use a true M3 screw so it does not cross-thread or strip the hole.

Where can I buy replacement screws for Elo EMV bracket assembly special pan-head screw?

TechSpareWarehouse (our own store) lists M3 x 8mm, which matches the length in the records above.

Elo EMV bracket assembly special pan-head screw screw size

M3 · 8 mm long

The screws used on Elo EMV bracket assembly special pan-head screw are M3, 8 mm long.

The record covers verifone/Ingenico kits; SCREW_M3X8_SPECIAL.

This entry is marked confirmed and comes from docs.elotouch.com.

For reference, M3 is 3 mm across the threads at 0.5 mm pitch. The imperial size people confuse it with: #5-40 (3.18 mm) or #4-40 — neither interchanges with M3.

Elo EMV bracket assembly special pan-head screw screw specifications

One row per fitment record. Head, drive are shown only where the source states them; pitch is the ISO coarse pitch for the thread.

Thread	Length	Pitch	Head	Drive	Where it goes	Status
M3	8 mm	0.5 mm	not stated	not stated	Verifone/Ingenico kits; SCREW_M3X8_SPECIAL	Confirmed

Fitment records and sources

M38.0mmconfirmed

Verifone/Ingenico kits; SCREW_M3X8_SPECIAL

pitch 0.5 mm · tap 2.5 mm · clearance 3.4 mm · PH1 / Torx T10

Source

How to check the screw before you buy

Board standoffs and enclosure bosses set the usable length: the screw should clamp the board without bottoming in the standoff.
Diameter: across the threads an M3 screw measures about 3 mm with calipers (usually a hair under). If yours measures noticeably more or less, it is a different thread.
Pitch: 0.5 mm from one thread crest to the next (20 crests per centimetre). A thread pitch gauge or the pitch-gauge tool settles it in seconds.
Length: measure from under the head to the tip for pan, button, wafer and cap heads; countersunk (flat) heads are measured overall.
The record states 8 mm. Going longer risks bottoming out or touching parts behind the hole; going shorter loses thread engagement.
Driver: the source does not name the drive. Standard M3 heads take PH1 for Phillips and T10 for Torx, and a 2.5 mm hex key for socket heads; a bit that fits loosely will cam out and strip the head.
Tightening: no device-specific torque is published in these records. The site's general figure for M3 is about 80-130 N·cm into metal threads and 35-60 N·cm into plastic bosses; snug it up and stop.

Common mix-ups with M3

Pond/aquarium equipment manuals aimed at consumers rarely specify exact thread pitch or length for internal fasteners, since these are considered non-user-serviceable; distributor-level assembly/service manuals (e.g., Maytronics internal documents) are a better source than end-user guides.
M3 (3.0mm, 0.5mm pitch) is not #6-32 UNC (~3.5mm) — they look identical and cross-thread, the single most common PC-building mistake.

Pitch gauge · Screw size finder · Torque guide

Buy these screws at TechSpare Warehouse

In stock and shipped from South Carolina. Our black screws are Phillips wafer head (low profile); match the head style and length to the original before you order.

More in Electronics, Racks & Enclosures

19-inch rack cage nut (light equipment)19-inch rack cage nut (metric square-hole rails)19-inch rack cage nut (mid size)19-inch rack cage nut and panel screw 19-inch rack network and AV gear 19-inch rack-mount audio/AV equipment 19-inch server racks 19in / 10in server rack cage nut and screw kit 19in equipment rack (Kendall Howard cage nuts)19in rack cage nuts (alternate metric)19in rack cage nuts (metric)1U rack-mount PDU (American Denki)

Browse all 357 in Electronics, Racks & Enclosures →

The same screw also fits

Devices whose records share a thread with Elo EMV bracket assembly special pan-head screw, closest length match first.

Brother DCP-8080DN multifunction printer also M3 × 8 mm
POS / kiosk plastic enclosure screw also M3 × 8 mm
Eurorack panel/module mounting screws (standard rail systems) also M3 × 8 mm
Apple AirPort Extreme internals also M3 × 8 mm
Keystone metric hex PCB standoff also M3 × 8 mm
Eurorack synth rails (standard panel mounting) also M3 × 8 mm
Guitar pedal enclosure also M3 × 8 mm
GCX Barcode Scanner Adapter mounting kit also M3 × 8 mm

Questions about Elo EMV bracket assembly special pan-head screw screws

What size screw does Elo EMV bracket assembly special pan-head screw use?: M3 × 8 mm for verifone/Ingenico kits; SCREW_M3X8_SPECIAL.
How long are the screws in Elo EMV bracket assembly special pan-head screw?: The record gives 8 mm. Measure the original from under the head (overall for a countersunk head) to confirm before ordering.
What is the thread pitch of an M3 screw?: 0.5 mm (coarse), which is the standard pitch for M3 machine screws; a 0.35 mm fine pitch exists but is uncommon. The tap drill is 2.5 mm and the normal clearance hole is 3.4 mm.
What screwdriver do I need for Elo EMV bracket assembly special pan-head screw?: The sources do not name the drive. For M3, Phillips heads normally take PH1 and Torx heads T10; socket heads take a 2.5 mm hex key.
Can I use an imperial screw instead of M3?: No. Imperial look-alike: #5-40 (3.18 mm) or #4-40 — neither interchanges with M3. Use a true M3 screw so it does not cross-thread or strip the hole.
Where can I buy replacement screws for Elo EMV bracket assembly special pan-head screw?: TechSpareWarehouse (our own store) lists M3 x 8mm, which matches the length in the records above.

Heads up: shipping delay