EVoCharge EVSE charging station (EV charging kiosk electronics enclosure) screw size
M4 · 10 mm long
Our records put EVoCharge EVSE charging station (EV charging kiosk electronics enclosure) on M4 screws, 10 mm long.
The record covers EVOCHARGE EVSE Manual explicitly lists M4 screws for mounting the internal control board and terminal cover inside the EVSE enclosure.
This entry is marked likely and comes from evocharge.com.
M4 means a 4 mm nominal diameter with a 0.7 mm thread pitch. Imperial look-alike: #8-32 (4.17 mm) — the standard US PC/rack screw, close but not the same.
EVoCharge EVSE charging station (EV charging kiosk electronics enclosure) screw specifications
One row per fitment record. Head, drive are shown only where the source states them; pitch is the ISO coarse pitch for the thread.
| Thread | Length | Pitch | Head | Drive | Where it goes | Status |
|---|---|---|---|---|---|---|
| M4 | 10 mm | 0.7 mm | not stated | not stated | EVOCHARGE EVSE Manual explicitly lists M4 screws for mounting the internal control board and terminal cover inside the EVSE enclosure | Likely |
Fitment records and sources
EVOCHARGE EVSE Manual explicitly lists M4 screws for mounting the internal control board and terminal cover inside the EVSE enclosure
pitch 0.7 mm · tap 3.3 mm · clearance 4.5 mm · PH2 / Torx T20
How to check the screw before you buy
- Rack and enclosure hardware mixes metric and imperial (#8-32, #10-32, #6-32), so confirm the thread before forcing a screw.
- Diameter: across the threads an M4 screw measures about 4 mm with calipers (usually a hair under). If yours measures noticeably more or less, it is a different thread.
- Pitch: 0.7 mm from one thread crest to the next (14.29 crests per centimetre). A thread pitch gauge or the pitch-gauge tool settles it in seconds.
- Length: measure from under the head to the tip for pan, button, wafer and cap heads; countersunk (flat) heads are measured overall.
- The record states 10 mm. Going longer risks bottoming out or touching parts behind the hole; going shorter loses thread engagement.
- Driver: the source does not name the drive. Standard M4 heads take PH2 for Phillips and T20 for Torx, and a 3 mm hex key for socket heads; a bit that fits loosely will cam out and strip the head.
- Tightening: no device-specific torque is published in these records. The site's general figure for M4 is about 2.0-3.0 N·m into metal threads and 0.8-1.4 N·m into plastic bosses; snug it up and stop.
Common mix-ups with M4
- Grounding/earth-stud screws on hazardous-area (ATEX/IECEx) gas detectors are commonly M4 even though the enclosure body uses larger threaded glands — don't extrapolate the earth screw size to the whole unit.
- In EV charging part numbers 'M3'/'M4' often means IEC 61851 charging Mode 3/Mode 4, not a screw thread.
Buy these screws at TechSpare Warehouse
In stock and shipped from South Carolina. Our black screws are Phillips wafer head (low profile); match the head style and length to the original before you order.
More in Electronics, Racks & Enclosures
The same screw also fits
Devices whose records share a thread with EVoCharge EVSE charging station (EV charging kiosk electronics enclosure), closest length match first.
- Electronics enclosures also M4 × 10 mm
- UniFi rack shelf and tray hardware also M4 × 10 mm
- J-GUANG 2EDGKM-7.62 high-current power terminal block also M4 × 10 mm
- Keystone Electronics metric nylon standoff also M4 × 10 mm
- Neopost/Paper-Machines 7104 Series High-Volume Modular Inserter (mailroom sorting/inserting machine) also M4 × 10 mm
- Marine electronics housings also M4 × 10 mm
- Soundbar wall brackets also M4 × 10 mm
- ABB ACS880-87CC wind turbine converter (nacelle power converter hardware manual) also M4 × 10 mm
Questions about EVoCharge EVSE charging station (EV charging kiosk electronics enclosure) screws
- What size screw does EVoCharge EVSE charging station (EV charging kiosk electronics enclosure) use?
- M4 × 10 mm for EVOCHARGE EVSE Manual explicitly lists M4 screws for mounting the internal control board and terminal cover inside the EVSE enclosure.
- How long are the screws in EVoCharge EVSE charging station (EV charging kiosk electronics enclosure)?
- The record gives 10 mm. Measure the original from under the head (overall for a countersunk head) to confirm before ordering.
- What is the thread pitch of an M4 screw?
- 0.7 mm (coarse), which is the standard pitch for M4 machine screws; a 0.5 mm fine pitch exists but is uncommon. The tap drill is 3.3 mm and the normal clearance hole is 4.5 mm.
- What screwdriver do I need for EVoCharge EVSE charging station (EV charging kiosk electronics enclosure)?
- The sources do not name the drive. For M4, Phillips heads normally take PH2 and Torx heads T20; socket heads take a 3 mm hex key.
- Can I use an imperial screw instead of M4?
- No. Imperial look-alike: #8-32 (4.17 mm) — the standard US PC/rack screw, close but not the same. Use a true M4 screw so it does not cross-thread or strip the hole.