Framework Laptop 12 bezel and hinge fasteners screw size
M1.6 · 1.5 to 3 mm long
Our records put Framework Laptop 12 bezel and hinge fasteners on M1.6 screws in lengths from 1.5 to 3 mm.
Where it is used: official Framework fastener guide covers M1.6 screws for thin bezel/hinge attachment.
This entry is marked confirmed and comes from ifixit.com.
M1.6 means a 1.6 mm nominal diameter with a 0.35 mm thread pitch. Imperial look-alike: #1-72 UNF (1.85 mm) is larger; there is no true imperial equivalent.
Framework Laptop 12 bezel and hinge fasteners screw specifications
One row per fitment record. Head, drive are shown only where the source states them; pitch is the ISO coarse pitch for the thread.
| Thread | Length | Pitch | Head | Drive | Where it goes | Status |
|---|---|---|---|---|---|---|
| M1.6 | 1.5–3 mm | 0.35 mm | not stated | not stated | Official Framework fastener guide covers M1.6 screws for thin bezel/hinge attachment | Confirmed |
Fitment records and sources
Official Framework fastener guide covers M1.6 screws for thin bezel/hinge attachment
pitch 0.35 mm · tap 1.25 mm · clearance 1.8 mm · PH00 / Torx T4–T5
How to check the screw before you buy
- A screw that is even 1 mm too long in a laptop base can push into the keyboard, battery or a board trace, so match the length position by position.
- Diameter: across the threads an M1.6 screw measures about 1.6 mm with calipers (usually a hair under). If yours measures noticeably more or less, it is a different thread.
- Pitch: 0.35 mm from one thread crest to the next (28.57 crests per centimetre). A thread pitch gauge or the pitch-gauge tool settles it in seconds.
- Length: measure from under the head to the tip for pan, button, wafer and cap heads; countersunk (flat) heads are measured overall.
- The records span 1.5–3 mm, which means different positions take different lengths — match each hole to its own screw.
- Driver: the source does not name the drive. Standard M1.6 heads take PH00 for Phillips and T4–T5 for Torx, and a 1.5 mm hex key for socket heads; a bit that fits loosely will cam out and strip the head.
- Tightening: no device-specific torque is published in these records. The site's general figure for M1.6 is about 12-20 N·cm into metal threads and 6-10 N·cm into plastic bosses; snug it up and stop.
Common mix-ups with M1.6
- M1.6 is the most common laptop-internal micro screw after M2 — Dell XPS keyboards specifically call out M1.6 x 1.5mm, and generic M2 substitutes strip the bracket.
- Headphone hinge screw sizes are usually quoted from screwdriver bit size, not an actual thread spec - measure before buying.
Buy these screws at TechSpare Warehouse
In stock and shipped from South Carolina. Our black screws are Phillips wafer head (low profile); match the head style and length to the original before you order.
-
M1.6 x 3mm Screws Compatible with Dell XPS 13 9340 Keyboard 10-Pack Black
$4.99 -
M1.6 x 3mm Screws for Dell XPS 13 9340 System Board Replacement 10-Pack Black
$4.99
-
M1.6 x 2mm Black Wafer Head Keyboard & Speaker Screws for HP ZBook Fury G1i 18 – 70-Pack Replacement
$7.99Choose size -
M1.6 x 2mm Black Wafer Head M.2 2230 SSD Screws for Alienware m15 R1 & Dell Inspiron 15 5502 – 10-Pack Replacement
$4.99Choose size -
ASUS ROG Strix G15 G513R Replacement Screws Sold Individually – M1.6 x 3mm, M2 x 2.5mm, M2 x 3mm, M2.5 x 6mm Phillips Wafer Head, Black
$0.10Choose size -
ASUS ROG Strix G17 G713 Replacement Screws Sold Individually – M1.6 x 3mm, M2 x 2.5mm, M2 x 3mm, M2.5 x 6mm Phillips Wafer Head, Black
$0.10Choose size
More in Laptops & PCs
2.5in drive trays & caddiesAcer / MSI laptopsAcer 5510/4020 series I/O and misc chassis screwsAcer 7520 / 7220Acer Aspire / Swift bottom coverAcer Aspire / Swift M.2 SSDAcer Aspire 1310Acer Aspire 1410Acer Aspire 1420PAcer Aspire 1650Acer Aspire 1680Acer Aspire 1690
Browse all 2799 in Laptops & PCs →The same screw also fits
Devices whose records share a thread with Framework Laptop 12 bezel and hinge fasteners, closest length match first.
- Dell Inspiron 14 5420 also M1.6 × 2 mm
- Dell Alienware m15 also M1.6 × 2 mm
- Framework Laptop 13 bottom cover / mainboard kit also M1.6 × 1.5 mm
- Dell XPS 14 9440 also M1.6 × 3 mm
- Lenovo Yoga Pro 7 14AKP10 also M1.6 × 1.7 mm
- Ultra-thin laptop Wi-Fi / M.2 retention also M1.6 × 1.5–2 mm
- Dell Alienware m17 also M1.6 × 2 mm
- MacBook Pro 15-inch Retina (Mid 2015) lower case also M1.6 × 2.3–3 mm
Questions about Framework Laptop 12 bezel and hinge fasteners screws
- What size screw does Framework Laptop 12 bezel and hinge fasteners use?
- M1.6 × 1.5–3 mm for official Framework fastener guide covers M1.6 screws for thin bezel/hinge attachment.
- How long are the screws in Framework Laptop 12 bezel and hinge fasteners?
- The records range from 1.5 to 3 mm depending on the position, so match each screw to its own hole.
- What is the thread pitch of an M1.6 screw?
- 0.35 mm (coarse), which is the standard pitch for M1.6 machine screws; a 0.2 mm fine pitch exists but is uncommon. The tap drill is 1.25 mm and the normal clearance hole is 1.8 mm.
- What screwdriver do I need for Framework Laptop 12 bezel and hinge fasteners?
- The sources do not name the drive. For M1.6, Phillips heads normally take PH00 and Torx heads T4–T5; socket heads take a 1.5 mm hex key.
- Can I use an imperial screw instead of M1.6?
- No. Imperial look-alike: #1-72 UNF (1.85 mm) is larger; there is no true imperial equivalent. Use a true M1.6 screw so it does not cross-thread or strip the hole.
- Where can I buy replacement screws for Framework Laptop 12 bezel and hinge fasteners?
- TechSpareWarehouse (our own store) lists M1.6 x 3mm, which matches the length in the records above.