Framework Laptop 13 mainboard and webcam module screw screw size
M1.6 · 1.5 mm long
Our records put Framework Laptop 13 mainboard and webcam module screw on M1.6 screws, 1.5 mm long.
Where it is used: T5 head, 5.5mm head dia.
Head and drive, as the source states them: Torx T5 drive.
This entry is marked confirmed and comes from guides.frame.work.
M1.6 means a 1.6 mm nominal diameter with a 0.35 mm thread pitch. Imperial look-alike: #1-72 UNF (1.85 mm) is larger; there is no true imperial equivalent.
Framework Laptop 13 mainboard and webcam module screw screw specifications
One row per fitment record. Head, drive are shown only where the source states them; pitch is the ISO coarse pitch for the thread.
| Thread | Length | Pitch | Head | Drive | Where it goes | Status |
|---|---|---|---|---|---|---|
| M1.6 | 1.5 mm | 0.35 mm | not stated | Torx T5 | T5 head, 5.5mm head dia | Confirmed |
Fitment records and sources
T5 head, 5.5mm head dia
pitch 0.35 mm · tap 1.25 mm · clearance 1.8 mm · PH00 / Torx T4–T5
How to check the screw before you buy
- A screw that is even 1 mm too long in a laptop base can push into the keyboard, battery or a board trace, so match the length position by position.
- Diameter: across the threads an M1.6 screw measures about 1.6 mm with calipers (usually a hair under). If yours measures noticeably more or less, it is a different thread.
- Pitch: 0.35 mm from one thread crest to the next (28.57 crests per centimetre). A thread pitch gauge or the pitch-gauge tool settles it in seconds.
- Length: measure from under the head to the tip for pan, button, wafer and cap heads; countersunk (flat) heads are measured overall.
- The record states 1.5 mm. Going longer risks bottoming out or touching parts behind the hole; going shorter loses thread engagement.
- Driver: the source names a Torx T5 drive. For comparison, standard M1.6 heads take PH00 (Phillips) or T4–T5 (Torx), or a 1.5 mm hex key.
- Tightening: no device-specific torque is published in these records. The site's general figure for M1.6 is about 12-20 N·cm into metal threads and 6-10 N·cm into plastic bosses; snug it up and stop.
Common mix-ups with M1.6
- M1.6 is the most common laptop-internal micro screw after M2 — Dell XPS keyboards specifically call out M1.6 x 1.5mm, and generic M2 substitutes strip the bracket.
More in Laptops & PCs
2.5in drive trays & caddiesAcer / MSI laptopsAcer 5510/4020 series I/O and misc chassis screwsAcer 7520 / 7220Acer Aspire / Swift bottom coverAcer Aspire / Swift M.2 SSDAcer Aspire 1310Acer Aspire 1410Acer Aspire 1420PAcer Aspire 1650Acer Aspire 1680Acer Aspire 1690
Browse all 2799 in Laptops & PCs →The same screw also fits
Devices whose records share a thread with Framework Laptop 13 mainboard and webcam module screw, closest length match first.
- Framework Laptop 13 mainboard and webcam module also M1.6 × 1.5 mm
- Framework Laptop 16 also M1.6 × 1.5 mm
- HP Elite x2 1012 G1 Tablet with Travel Keyboard also M1.6 × 1.5 mm
- Framework Laptop 12 also M1.6 × 1.5 mm
- Framework Laptop 13 mainboard and webcam also M1.6 × 1.5 mm
- Framework Laptop 13 bottom cover also M1.6 × 1.5 mm
- Dell XPS 13 9380 also M1.6 × 1.5 mm
- HP Elite x2 1012 G1 Tablet with Advanced Keyboard also M1.6 × 1.5 mm
Questions about Framework Laptop 13 mainboard and webcam module screw screws
- What size screw does Framework Laptop 13 mainboard and webcam module screw use?
- M1.6 × 1.5 mm for T5 head, 5.5mm head dia.
- How long are the screws in Framework Laptop 13 mainboard and webcam module screw?
- The record gives 1.5 mm. Measure the original from under the head (overall for a countersunk head) to confirm before ordering.
- What is the thread pitch of an M1.6 screw?
- 0.35 mm (coarse), which is the standard pitch for M1.6 machine screws; a 0.2 mm fine pitch exists but is uncommon. The tap drill is 1.25 mm and the normal clearance hole is 1.8 mm.
- What screwdriver do I need for Framework Laptop 13 mainboard and webcam module screw?
- The source lists a Torx T5 drive. Standard M1.6 heads otherwise take PH00 (Phillips) or T4–T5 (Torx), or a 1.5 mm hex key.
- Can I use an imperial screw instead of M1.6?
- No. Imperial look-alike: #1-72 UNF (1.85 mm) is larger; there is no true imperial equivalent. Use a true M1.6 screw so it does not cross-thread or strip the hole.