Framework Laptop 16 chassis screw size
M2.5 · length not stated in the sources
Our records put Framework Laptop 16 chassis on M2.5 screws. None of the sources we found gives an exact length, so measure the original before you order.
The record covers framework's official fastener guide documents M2.5 structural fasteners per component.
This entry is marked confirmed and comes from ifixit.com.
For reference, M2.5 is 2.5 mm across the threads at 0.45 mm pitch. The imperial size people confuse it with: #3-48 / #4-40 (2.51 / 2.84 mm) — #4-40 is the common US stand-in and it will NOT thread in.
Framework Laptop 16 chassis screw specifications
One row per fitment record. Head, drive are shown only where the source states them; pitch is the ISO coarse pitch for the thread.
| Thread | Length | Pitch | Head | Drive | Where it goes | Status |
|---|---|---|---|---|---|---|
| M2.5 | not stated | 0.45 mm | not stated | not stated | Framework's official fastener guide documents M2.5 structural fasteners per component | Confirmed |
Fitment records and sources
Framework's official fastener guide documents M2.5 structural fasteners per component
pitch 0.45 mm · tap 2.05 mm · clearance 2.9 mm · PH1 / Torx T8
How to check the screw before you buy
- A screw that is even 1 mm too long in a laptop base can push into the keyboard, battery or a board trace, so match the length position by position.
- Diameter: across the threads an M2.5 screw measures about 2.5 mm with calipers (usually a hair under). If yours measures noticeably more or less, it is a different thread.
- Pitch: 0.45 mm from one thread crest to the next (22.22 crests per centimetre). A thread pitch gauge or the pitch-gauge tool settles it in seconds.
- Length: measure from under the head to the tip for pan, button, wafer and cap heads; countersunk (flat) heads are measured overall.
- Driver: the source does not name the drive. Standard M2.5 heads take PH1 for Phillips and T8 for Torx, and a 2 mm hex key for socket heads; a bit that fits loosely will cam out and strip the head.
- Tightening: no device-specific torque is published in these records. The site's general figure for M2.5 is about 45-70 N·cm into metal threads and 20-35 N·cm into plastic bosses; snug it up and stop.
Common mix-ups with M2.5
- M2.5 and M3 look the same to the naked eye — you need calipers on the shank to tell them apart.
- M2.5 pitch is 0.45mm vs M3's 0.5mm and M2's 0.4mm — forcing the wrong one strips plastic bosses instantly.
More in Laptops & PCs
The same screw also fits
Devices whose records share a thread with Framework Laptop 16 chassis, closest length match first.
- HP EliteBook 830 G9 also M2.5
- Dell Inspiron 14 5485 also M2.5
- Dell Inspiron 14 5491 also M2.5
- HP Pavilion / Omen hinges also M2.5
- Lenovo ThinkPad T14s Gen 2 also M2.5
- Dell Vostro 14 5402 also M2.5
- ASUS ROG Zephyrus M16 (GU603) also M2.5
- Dell Alienware x15 R2 also M2.5
Questions about Framework Laptop 16 chassis screws
- What size screw does Framework Laptop 16 chassis use?
- M2.5 for framework's official fastener guide documents M2.5 structural fasteners per component.
- How long are the screws in Framework Laptop 16 chassis?
- None of the sources states a length. Remove one screw and measure it from under the head to the tip (overall for a countersunk head).
- What is the thread pitch of an M2.5 screw?
- 0.45 mm (coarse), which is the standard pitch for M2.5 machine screws; a 0.35 mm fine pitch exists but is uncommon. The tap drill is 2.05 mm and the normal clearance hole is 2.9 mm.
- What screwdriver do I need for Framework Laptop 16 chassis?
- The sources do not name the drive. For M2.5, Phillips heads normally take PH1 and Torx heads T8; socket heads take a 2 mm hex key.
- Can I use an imperial screw instead of M2.5?
- No. Imperial look-alike: #3-48 / #4-40 (2.51 / 2.84 mm) — #4-40 is the common US stand-in and it will NOT thread in. Use a true M2.5 screw so it does not cross-thread or strip the hole.