Framework Laptop 16 expansion bay screw size
M2 · length not stated in the sources
Our records put Framework Laptop 16 expansion bay on M2 screws. None of the sources we found gives an exact length, so measure the original before you order.
The record covers expansion cards and bottom cover.
This entry is marked reported and comes from guides.frame.work.
M2 means a 2 mm nominal diameter with a 0.4 mm thread pitch. Imperial look-alike: #2-56 UNC (2.18 mm) is close but not interchangeable.
Framework Laptop 16 expansion bay screw specifications
One row per fitment record. Head, drive are shown only where the source states them; pitch is the ISO coarse pitch for the thread.
| Thread | Length | Pitch | Head | Drive | Where it goes | Status |
|---|---|---|---|---|---|---|
| M2 | not stated | 0.4 mm | not stated | not stated | expansion cards and bottom cover | Reported |
Fitment records and sources
expansion cards and bottom cover
pitch 0.4 mm · tap 1.6 mm · clearance 2.4 mm · PH0 / Torx T6
How to check the screw before you buy
- A screw that is even 1 mm too long in a laptop base can push into the keyboard, battery or a board trace, so match the length position by position.
- Diameter: across the threads an M2 screw measures about 2 mm with calipers (usually a hair under). If yours measures noticeably more or less, it is a different thread.
- Pitch: 0.4 mm from one thread crest to the next (25 crests per centimetre). A thread pitch gauge or the pitch-gauge tool settles it in seconds.
- Length: measure from under the head to the tip for pan, button, wafer and cap heads; countersunk (flat) heads are measured overall.
- Driver: the source does not name the drive. Standard M2 heads take PH0 for Phillips and T6 for Torx, and a 1.5 mm hex key for socket heads; a bit that fits loosely will cam out and strip the head.
- Tightening: no device-specific torque is published in these records. The site's general figure for M2 is about 25-40 N·cm into metal threads and 12-20 N·cm into plastic bosses; snug it up and stop.
Common mix-ups with M2
- The standard M.2 SSD screw is M2 x 3mm, but some laptops and handhelds use non-standard lengths or head shapes.
- Framework 13 and 16 use five thread families (M1.2 to M2.5) with overlapping lengths; buy Framework's own fastener kit rather than generic M2 screws.
Buy these screws at TechSpare Warehouse
In stock and shipped from South Carolina. Our black screws are Phillips wafer head (low profile); match the head style and length to the original before you order.
-
ASUS ROG Strix G15 G513R Replacement Screws Sold Individually – M1.6 x 3mm, M2 x 2.5mm, M2 x 3mm, M2.5 x 6mm Phillips Wafer Head, Black
$0.10Choose size -
ASUS ROG Strix G17 G713 Replacement Screws Sold Individually – M1.6 x 3mm, M2 x 2.5mm, M2 x 3mm, M2.5 x 6mm Phillips Wafer Head, Black
$0.10Choose size
More in Laptops & PCs
The same screw also fits
Devices whose records share a thread with Framework Laptop 16 expansion bay, closest length match first.
- HP Compaq Presario C300 also M2
- Lenovo YOGA 3 Pro-1370 also M2
- Dell Precision 5470 also M2
- Lenovo ThinkPad 765D also M2
- Lenovo Z510 also M2
- Dell Inspiron 14 3462 also M2
- HP Pavilion 4300 also M2
- HP OMEN 17-w2xx also M2
Questions about Framework Laptop 16 expansion bay screws
- What size screw does Framework Laptop 16 expansion bay use?
- M2 for expansion cards and bottom cover.
- How long are the screws in Framework Laptop 16 expansion bay?
- None of the sources states a length. Remove one screw and measure it from under the head to the tip (overall for a countersunk head).
- What is the thread pitch of an M2 screw?
- 0.4 mm (coarse), which is the standard pitch for M2 machine screws; a 0.25 mm fine pitch exists but is uncommon. The tap drill is 1.6 mm and the normal clearance hole is 2.4 mm.
- What screwdriver do I need for Framework Laptop 16 expansion bay?
- The sources do not name the drive. For M2, Phillips heads normally take PH0 and Torx heads T6; socket heads take a 1.5 mm hex key.
- Can I use an imperial screw instead of M2?
- No. Imperial look-alike: #2-56 UNC (2.18 mm) is close but not interchangeable. Use a true M2 screw so it does not cross-thread or strip the hole.