What size screw does GPU rear bracket anchor use?

M3 × 5–6 mm for secures the graphics card bracket to the case.

How long are the screws in GPU rear bracket anchor?

The records range from 5 to 6 mm depending on the position, so match each screw to its own hole.

What is the thread pitch of an M3 screw?

0.5 mm (coarse), which is the standard pitch for M3 machine screws; a 0.35 mm fine pitch exists but is uncommon. The tap drill is 2.5 mm and the normal clearance hole is 3.4 mm.

What screwdriver do I need for GPU rear bracket anchor?

The sources do not name the drive. For M3, Phillips heads normally take PH1 and Torx heads T10; socket heads take a 2.5 mm hex key.

Can I use an imperial screw instead of M3?

No. Imperial look-alike: #5-40 (3.18 mm) or #4-40 — neither interchanges with M3. Use a true M3 screw so it does not cross-thread or strip the hole.

Where can I buy replacement screws for GPU rear bracket anchor?

TechSpareWarehouse (our own store) lists M3 x 5mm and M3 x 6mm, which match lengths in the records above.

GPU rear bracket anchor screw size

M3 · 5 to 6 mm long

Our records put GPU rear bracket anchor on M3 screws in lengths from 5 to 6 mm.

Where it is used: secures the graphics card bracket to the case.

This entry is marked reported and comes from alibaba.com.

For reference, M3 is 3 mm across the threads at 0.5 mm pitch. The imperial size people confuse it with: #5-40 (3.18 mm) or #4-40 — neither interchanges with M3.

GPU rear bracket anchor screw specifications

One row per fitment record. Head, drive are shown only where the source states them; pitch is the ISO coarse pitch for the thread.

Thread	Length	Pitch	Head	Drive	Where it goes	Status
M3	5–6 mm	0.5 mm	not stated	not stated	secures the graphics card bracket to the case	Reported

Fitment records and sources

M35-6mmreported

secures the graphics card bracket to the case

pitch 0.5 mm · tap 2.5 mm · clearance 3.4 mm · PH1 / Torx T10

Source

How to check the screw before you buy

Rack and enclosure hardware mixes metric and imperial (#8-32, #10-32, #6-32), so confirm the thread before forcing a screw.
Diameter: across the threads an M3 screw measures about 3 mm with calipers (usually a hair under). If yours measures noticeably more or less, it is a different thread.
Pitch: 0.5 mm from one thread crest to the next (20 crests per centimetre). A thread pitch gauge or the pitch-gauge tool settles it in seconds.
Length: measure from under the head to the tip for pan, button, wafer and cap heads; countersunk (flat) heads are measured overall.
The records span 5–6 mm, which means different positions take different lengths — match each hole to its own screw.
Driver: the source does not name the drive. Standard M3 heads take PH1 for Phillips and T10 for Torx, and a 2.5 mm hex key for socket heads; a bit that fits loosely will cam out and strip the head.
Tightening: no device-specific torque is published in these records. The site's general figure for M3 is about 80-130 N·cm into metal threads and 35-60 N·cm into plastic bosses; snug it up and stop.

Common mix-ups with M3

M3 (3.0mm, 0.5mm pitch) is not #6-32 UNC (~3.5mm) — they look identical and cross-thread, the single most common PC-building mistake.

Pitch gauge · Screw size finder · Torque guide

Buy these screws at TechSpare Warehouse

In stock and shipped from South Carolina. Our black screws are Phillips wafer head (low profile); match the head style and length to the original before you order.

M3 x 5mm Phillips Wafer Head Screw for Electronics & Project Box Repair - Pack of 50 Black $4.79 each · min. 2
M3 x 6mm Replacement Screws for XLR Audio Connectors Phillips Wafer Head 50-Pack $4.99
M3 x 6mm Phillips Wafer Head Carbon Steel Machine Screws for XLR Audio Connectors | 50-Pack (Black) $4.99
M3 x 6mm Phillips Wafer Head Screw for 3D Printer Frame Assembly - Single Replacement Black $0.10 each · min. 50
M3 x 6mm Phillips Wafer Head Screw for Boutique Guitar Pedal Enclosure - Single Replacement Black $0.10 each · min. 50

More in Electronics, Racks & Enclosures

19-inch rack cage nut (light equipment)19-inch rack cage nut (metric square-hole rails)19-inch rack cage nut (mid size)19-inch rack cage nut and panel screw 19-inch rack network and AV gear 19-inch rack-mount audio/AV equipment 19-inch server racks 19in / 10in server rack cage nut and screw kit 19in equipment rack (Kendall Howard cage nuts)19in rack cage nuts (alternate metric)19in rack cage nuts (metric)1U rack-mount PDU (American Denki)

Browse all 357 in Electronics, Racks & Enclosures →

The same screw also fits

Devices whose records share a thread with GPU rear bracket anchor, closest length match first.

Eurorack panel/module mounting screws (standard rail systems) also M3 × 6 mm
Generic M3x6 pan head machine screw (DIN 7985H) stock item also M3 × 6 mm
Keyence IV series vision sensor also M3 × 6 mm
EK-Loop vertical GPU holder also M3 × 6 mm
Network switch & patch panel internals also M3 × 5–6 mm
Brother DCP-8080DN multifunction printer also M3 × 6 mm
Guitar pedal enclosure also M3 × 6 mm
Eurorack synth rails (standard panel mounting) also M3 × 6 mm

Questions about GPU rear bracket anchor screws

What size screw does GPU rear bracket anchor use?: M3 × 5–6 mm for secures the graphics card bracket to the case.
How long are the screws in GPU rear bracket anchor?: The records range from 5 to 6 mm depending on the position, so match each screw to its own hole.
What is the thread pitch of an M3 screw?: 0.5 mm (coarse), which is the standard pitch for M3 machine screws; a 0.35 mm fine pitch exists but is uncommon. The tap drill is 2.5 mm and the normal clearance hole is 3.4 mm.
What screwdriver do I need for GPU rear bracket anchor?: The sources do not name the drive. For M3, Phillips heads normally take PH1 and Torx heads T10; socket heads take a 2.5 mm hex key.
Can I use an imperial screw instead of M3?: No. Imperial look-alike: #5-40 (3.18 mm) or #4-40 — neither interchanges with M3. Use a true M3 screw so it does not cross-thread or strip the hole.
Where can I buy replacement screws for GPU rear bracket anchor?: TechSpareWarehouse (our own store) lists M3 x 5mm and M3 x 6mm, which match lengths in the records above.

Heads up: shipping delay