Henny Penny pressure fryer / combi oven screw size
M4 · 30 mm long
Our records put Henny Penny pressure fryer / combi oven on M4 screws, 30 mm long.
Where it is used: hexagon screw M4 x 30 mm, OEM part MM102005.
This entry is marked confirmed and comes from schedule73parts.us.
M4 means a 4 mm nominal diameter with a 0.7 mm thread pitch. Imperial look-alike: #8-32 (4.17 mm) — the standard US PC/rack screw, close but not the same.
Henny Penny pressure fryer / combi oven screw specifications
One row per fitment record. Head, drive are shown only where the source states them; pitch is the ISO coarse pitch for the thread.
| Thread | Length | Pitch | Head | Drive | Where it goes | Status |
|---|---|---|---|---|---|---|
| M4 | 30 mm | 0.7 mm | not stated | not stated | Hexagon screw M4 x 30 mm, OEM part MM102005 | Confirmed |
Fitment records and sources
Hexagon screw M4 x 30 mm, OEM part MM102005
pitch 0.7 mm · tap 3.3 mm · clearance 4.5 mm · PH2 / Torx T20
How to check the screw before you buy
- Unplug the appliance and discharge any capacitors before removing covers.
- Diameter: across the threads an M4 screw measures about 4 mm with calipers (usually a hair under). If yours measures noticeably more or less, it is a different thread.
- Pitch: 0.7 mm from one thread crest to the next (14.29 crests per centimetre). A thread pitch gauge or the pitch-gauge tool settles it in seconds.
- Length: measure from under the head to the tip for pan, button, wafer and cap heads; countersunk (flat) heads are measured overall.
- The record states 30 mm. Going longer risks bottoming out or touching parts behind the hole; going shorter loses thread engagement.
- Driver: the source does not name the drive. Standard M4 heads take PH2 for Phillips and T20 for Torx, and a 3 mm hex key for socket heads; a bit that fits loosely will cam out and strip the head.
- Tightening: no device-specific torque is published in these records. The site's general figure for M4 is about 2.0-3.0 N·m into metal threads and 0.8-1.4 N·m into plastic bosses; snug it up and stop.
Common mix-ups with M4
- Most HVAC chassis hardware in US-market units is imperial; metric shows up mainly on European-made components.
- M4 and 6-32 UNC share a nominal diameter with different pitch — a classic cross-thread in US-market kits.
More in Appliances & HVAC
Appliance door hingesAppliance handlesAstoria/CMA espresso solenoid group head (used in coffee kiosk equipment)Astoria/CMA espresso solenoid group head screwBerkel 330M Slicer cover fastenerBerkel 330M Slicer sharpener/guard mountingBezzera Giulia espresso machineBosch dishwasherCoffee machine control panelDaikin FTXS/CTXS Mini-split control board / cover screwDaikin FTXS/CTXS Mini-split indoor unit mounting / terminal cover screwDaikin FTXS/CTXS Mini-split indoor unit terminal cover / mounting plate screw
Browse all 62 in Appliances & HVAC →The same screw also fits
Devices whose records share a thread with Henny Penny pressure fryer / combi oven, closest length match first.
- Philips IntelliVue MP80/MP90 monitor also M4 × 30 mm
- Panasonic TC-L42D30 also M4 × 30 mm
- Kolm Engines EZ77V4 model aircraft engine also M4 × 30 mm
- Ottobock 17AD1 multifunctional ankle joint screw also M4 × 30 mm
- Atdec Telehook TH-2250-VF display wall mount also M4 × 30 mm
- Heated bed leveling screws also M4 × 30 mm
- cab Applicator A3200 print-and-apply labeling system (packaging line hardware) also M4 × 30 mm
- Makita 1806B planer also M4 × 30 mm
Questions about Henny Penny pressure fryer / combi oven screws
- What size screw does Henny Penny pressure fryer / combi oven use?
- M4 × 30 mm for hexagon screw M4 x 30 mm, OEM part MM102005.
- How long are the screws in Henny Penny pressure fryer / combi oven?
- The record gives 30 mm. Measure the original from under the head (overall for a countersunk head) to confirm before ordering.
- What is the thread pitch of an M4 screw?
- 0.7 mm (coarse), which is the standard pitch for M4 machine screws; a 0.5 mm fine pitch exists but is uncommon. The tap drill is 3.3 mm and the normal clearance hole is 4.5 mm.
- What screwdriver do I need for Henny Penny pressure fryer / combi oven?
- The sources do not name the drive. For M4, Phillips heads normally take PH2 and Torx heads T20; socket heads take a 3 mm hex key.
- Can I use an imperial screw instead of M4?
- No. Imperial look-alike: #8-32 (4.17 mm) — the standard US PC/rack screw, close but not the same. Use a true M4 screw so it does not cross-thread or strip the hole.