Hikvision DS-1271ZJ-130-TRL pendant bracket screw size
M4 · length not stated in the sources
Hikvision DS-1271ZJ-130-TRL pendant bracket takes M4 metric screws. None of the sources we found gives an exact length, so measure the original before you order.
Where it is used: six tapped bracket base holes for turret camera pendant assembly.
This entry is marked confirmed and comes from Hikvision DS-1271ZJ-130-TRL datasheet dimension drawing.
An M4 screw is 4 mm in diameter with a 0.7 mm pitch, tapped with a 3.3 mm drill; imperial look-alike: #8-32 (4.17 mm) — the standard US PC/rack screw, close but not the same.
Hikvision DS-1271ZJ-130-TRL pendant bracket screw specifications
One row per fitment record. Head, drive are shown only where the source states them; pitch is the ISO coarse pitch for the thread.
| Thread | Length | Pitch | Head | Drive | Where it goes | Status |
|---|---|---|---|---|---|---|
| M4 | not stated | 0.7 mm | not stated | not stated | six tapped bracket base holes for turret camera pendant assembly | Confirmed |
Fitment records and sources
six tapped bracket base holes for turret camera pendant assembly
pitch 0.7 mm · tap 3.3 mm · clearance 4.5 mm · PH2 / Torx T20
Source: Hikvision DS-1271ZJ-130-TRL datasheet dimension drawing
How to check the screw before you buy
- Do not confuse metric mounting screws with the 1/4-20 or 3/8-16 tripod threads that cameras and clamps also carry.
- Diameter: across the threads an M4 screw measures about 4 mm with calipers (usually a hair under). If yours measures noticeably more or less, it is a different thread.
- Pitch: 0.7 mm from one thread crest to the next (14.29 crests per centimetre). A thread pitch gauge or the pitch-gauge tool settles it in seconds.
- Length: measure from under the head to the tip for pan, button, wafer and cap heads; countersunk (flat) heads are measured overall.
- Driver: the source does not name the drive. Standard M4 heads take PH2 for Phillips and T20 for Torx, and a 3 mm hex key for socket heads; a bit that fits loosely will cam out and strip the head.
- Tightening: no device-specific torque is published in these records. The site's general figure for M4 is about 2.0-3.0 N·m into metal threads and 0.8-1.4 N·m into plastic bosses; snug it up and stop.
Common mix-ups with M4
- US-made pinball machines (Williams/Bally/Stern) overwhelmingly use imperial UTS threads (#6-32, #8-32, #10-32); explicit metric threads only appear on newer/import components such as Jersey Jack Pinball's Hobbit Smaug assembly (M3).
- Dashcam mounts advertised as '1/4" M4 screw joint' have two different threads: the 1/4"-20 camera thread and a separate M4 grub screw for the ball joint — don't order the wrong one.
More in Cameras & Optics
1.25" eyepiece/diagonal/SCT visual back thumb screwAimpoint Comp M4 / M4s LRP & TNP mountAimpoint Micro T-1/T-2/H-1/H-2 standard mountAimpoint Micro T-1/T-2/H-1/H-2 standard mount screwAimpoint SM-2001/2007 Micro T1/T2 mountAirsoft red dot sight mounting screw set (Laylax/Quintes Sence)Airsoft/firearm red-dot sight optic mounting screws (Vortex Viper, Swampfox patterns)Alpine and touring ski bindings (Binding Freedom inserts)Arca-style quick-release plateARRI plate for Sony VENICE 1/2Artesky 340mm Vixen Dovetail BarAstromania finder scope dovetail base
Browse all 278 in Cameras & Optics →The same screw also fits
Devices whose records share a thread with Hikvision DS-1271ZJ-130-TRL pendant bracket, closest length match first.
- Telescope finder-scope shoe / base (TS-Optics) also M4
- Wimberley AP-602 replacement plate also M4
- Holosun EPS Carry screw, Glock 43X/48 MOS also M4
- DJI RS gimbal accessory screws (RS2/RS3/RS4/RS5) also M4
- Thorlabs cage system adapters (16 to 30mm, 30 to 60mm) also M4
- Leica M125/M165/M205 stereo microscope stage also M4
- Thorlabs DLM1/M dual rotation mount also M4
- Thorlabs CCM1-BS013/M cage cube beamsplitter also M4
Questions about Hikvision DS-1271ZJ-130-TRL pendant bracket screws
- What size screw does Hikvision DS-1271ZJ-130-TRL pendant bracket use?
- M4 for six tapped bracket base holes for turret camera pendant assembly.
- How long are the screws in Hikvision DS-1271ZJ-130-TRL pendant bracket?
- None of the sources states a length. Remove one screw and measure it from under the head to the tip (overall for a countersunk head).
- What is the thread pitch of an M4 screw?
- 0.7 mm (coarse), which is the standard pitch for M4 machine screws; a 0.5 mm fine pitch exists but is uncommon. The tap drill is 3.3 mm and the normal clearance hole is 4.5 mm.
- What screwdriver do I need for Hikvision DS-1271ZJ-130-TRL pendant bracket?
- The sources do not name the drive. For M4, Phillips heads normally take PH2 and Torx heads T20; socket heads take a 3 mm hex key.
- Can I use an imperial screw instead of M4?
- No. Imperial look-alike: #8-32 (4.17 mm) — the standard US PC/rack screw, close but not the same. Use a true M4 screw so it does not cross-thread or strip the hole.