Hobart commercial mixer M802 / V1401 screw size
M5 · length not stated in the sources
Hobart commercial mixer M802 / V1401 takes M5 metric screws. None of the sources we found gives an exact length, so measure the original before you order.
The record covers cap screw M5 x 0.8 with 8 mm hex head.
Head and drive, as the source states them: socket cap head.
This entry is marked confirmed and comes from partstown.ca.
For reference, M5 is 5 mm across the threads at 0.8 mm pitch. The imperial size people confuse it with: #10-32 (4.83 mm) — the other common rack thread; check before mixing.
Hobart commercial mixer M802 / V1401 screw specifications
One row per fitment record. Head, drive are shown only where the source states them; pitch is the ISO coarse pitch for the thread.
| Thread | Length | Pitch | Head | Drive | Where it goes | Status |
|---|---|---|---|---|---|---|
| M5 | not stated | 0.8 mm | Socket cap | not stated | Cap screw M5 x 0.8 with 8 mm hex head | Confirmed |
Fitment records and sources
Cap screw M5 x 0.8 with 8 mm hex head
pitch 0.8 mm · tap 4.2 mm · clearance 5.5 mm · PH2 / Torx T25
How to check the screw before you buy
- Unplug the appliance and discharge any capacitors before removing covers.
- Diameter: across the threads an M5 screw measures about 5 mm with calipers (usually a hair under). If yours measures noticeably more or less, it is a different thread.
- Pitch: 0.8 mm from one thread crest to the next (12.5 crests per centimetre). A thread pitch gauge or the pitch-gauge tool settles it in seconds.
- Length: for socket cap screws, measure from under the head to the tip (countersunk heads are the exception: they are measured overall).
- Driver: the source does not name the drive. Standard M5 heads take PH2 for Phillips and T25 for Torx, and a 4 mm hex key for socket heads; a bit that fits loosely will cam out and strip the head.
- Tightening: no device-specific torque is published in these records. The site's general figure for M5 is about 4.0-6.0 N·m into metal threads and 1.5-2.5 N·m into plastic bosses; snug it up and stop.
Common mix-ups with M5
- Commercial washer-extractor cabinets mix DIN 933 (hex head, full thread) and DIN 84A (slotted pan/cheese head) M5 screws for different panels on the same machine line, so a single family/brand isn't consistent across all fasteners.
- Some scooters and appliances use self-tapping screws of similar diameter rather than true M5 machine threads.
More in Appliances & HVAC
Appliance door hingesAppliance handlesAstoria/CMA espresso solenoid group head (used in coffee kiosk equipment)Astoria/CMA espresso solenoid group head screwBerkel 330M Slicer cover fastenerBerkel 330M Slicer sharpener/guard mountingBezzera Giulia espresso machineBosch dishwasherCoffee machine control panelDaikin FTXS/CTXS Mini-split control board / cover screwDaikin FTXS/CTXS Mini-split indoor unit mounting / terminal cover screwDaikin FTXS/CTXS Mini-split indoor unit terminal cover / mounting plate screw
Browse all 62 in Appliances & HVAC →The same screw also fits
Devices whose records share a thread with Hobart commercial mixer M802 / V1401, closest length match first.
- Rancilio espresso group head shower screen screw also M5
- Eberspacher D4WS / D5WSC hydronic heater also M5
- Dishwasher toe kick panel also M5
- Espresso portafilter basket spring also M5
- Rancilio/Bezzera/Faema/Elektra/Pavoni espresso machine shower screen screw also M5
- Appliance handles also M5
- Vulcan-Hart Chef combi oven also M5
- Astoria/CMA espresso solenoid group head (used in coffee kiosk equipment) also M5
Questions about Hobart commercial mixer M802 / V1401 screws
- What size screw does Hobart commercial mixer M802 / V1401 use?
- M5 for cap screw M5 x 0.8 with 8 mm hex head.
- How long are the screws in Hobart commercial mixer M802 / V1401?
- None of the sources states a length. Remove one screw and measure it from under the head to the tip (overall for a countersunk head).
- What is the thread pitch of an M5 screw?
- 0.8 mm (coarse), which is the standard pitch for M5 machine screws; a 0.5 mm fine pitch exists but is uncommon. The tap drill is 4.2 mm and the normal clearance hole is 5.5 mm.
- What screwdriver do I need for Hobart commercial mixer M802 / V1401?
- The sources do not name the drive. For M5, Phillips heads normally take PH2 and Torx heads T25; socket heads take a 4 mm hex key.
- Can I use an imperial screw instead of M5?
- No. Imperial look-alike: #10-32 (4.83 mm) — the other common rack thread; check before mixing. Use a true M5 screw so it does not cross-thread or strip the hole.