HP Compaq nx6300 screw size

HP Compaq nx6300 screw specifications

One row per fitment record. Head, drive are shown only where the source states them; pitch is the ISO coarse pitch for the thread.

How to check the screw before you buy

1. A screw that is even 1 mm too long in a laptop base can push into the keyboard, battery or a board trace, so match the length position by position.
2. Diameter: across the threads an M2 screw measures about 2 mm with calipers (usually a hair under). This device also uses M2.5 / M3 / M5, so measure each screw rather than assuming they match.
3. Pitch: 0.4 mm from one thread crest to the next (25 crests per centimetre). A thread pitch gauge or the pitch-gauge tool settles it in seconds.
4. Length: for shoulder screw screws, measure from under the head to the tip (countersunk heads are the exception: they are measured overall).
5. The records span 2–13 mm, which means different positions take different lengths — match each hole to its own screw.
6. Driver: the source names a Torx T8 drive. For comparison, standard M2 heads take PH0 (Phillips) or T6 (Torx), or a 1.5 mm hex key.
7. Tightening: no device-specific torque is published in these records. The site's general figure for M2 is about 25-40 N·cm into metal threads and 12-20 N·cm into plastic bosses; snug it up and stop.

Pitch gauge · Screw size finder · Torque guide

More in Laptops & PCs

The same screw also fits

Devices whose records share a thread with HP Compaq nx6300, closest length match first.

• Lenovo ThinkPad P14s Gen 5 also M2 × 2 mm
• Lenovo G500 also M2 × 3 mm
• Acer TravelMate 7520G also M2 × 3 mm
• Lenovo ThinkPad S15 also M2 × 2 mm
• Dell Vostro 14 3491 also M2 × 2 mm
• Dell Inspiron 15 3580 also M2 × 2 mm
• Acer Aspire 7530G also M2 × 3 mm
• Lenovo G410s Touch also M2 × 3 mm

Questions about HP Compaq nx6300 screws

What size screw does HP Compaq nx6300 use?

M2 × 2 mm for wireless card (qty 2, Torx T8); M2 × 3 mm for I/O board (qty 1, Phillips); M2 × 4 mm for hard drive (qty 2, black, Phillips); M2 × 4 mm for memory (qty 1, black, Phillips); M2 × 4 mm for optical drive (qty 2, black, Phillips); M2 × 4 mm for speaker (qty 1, Torx T8); M2 × 4 mm for wireless card (qty 2, black, Phillips); M2 × 7 mm for fan (qty 2, Phillips); M2 × 8 mm for heat sink (qty 4, shoulder, Phillips); M2 × 9 mm for keyboard (qty 2, Torx T8); M2 × 9 mm for optical drive (qty 1, Torx T8); M2.5 × 13 mm for hard drive (qty 1, captive, silver, Phillips); M2.5 × 2 mm for unspecified (qty 2, black, Torx T8); M2.5 × 3 mm for unspecified (qty 2, black, Phillips); M2.5 × 4 mm for s.

How long are the screws in HP Compaq nx6300?

The records range from 2 to 13 mm depending on the position, so match each screw to its own hole.

What is the thread pitch of an M2 screw?

0.4 mm (coarse), which is the standard pitch for M2 machine screws; a 0.25 mm fine pitch exists but is uncommon. The tap drill is 1.6 mm and the normal clearance hole is 2.4 mm.

What screwdriver do I need for HP Compaq nx6300?

The source lists a Torx T8 and Phillips drive. Standard M2 heads otherwise take PH0 (Phillips) or T6 (Torx), or a 1.5 mm hex key.

Can I use an imperial screw instead of M2?

No. Imperial look-alike: #2-56 UNC (2.18 mm) is close but not interchangeable. Use a true M2 screw so it does not cross-thread or strip the hole.

Where can I buy replacement screws for HP Compaq nx6300?

TechSpareWarehouse (our own store) lists M2 x 2mm, M2 x 3mm and M2 x 4mm, which match lengths in the records above.