HP Compaq Presario R4000 screw size

HP Compaq Presario R4000 screw specifications

One row per fitment record. Head, drive are shown only where the source states them; pitch is the ISO coarse pitch for the thread.

How to check the screw before you buy

1. Laptop covers and brackets often mix two or three lengths of the same thread, so lay the screws out in the order they came out (a magnetic mat or a sheet of paper with the hole pattern drawn on it works).
2. Diameter: across the threads an M2 screw measures about 2 mm with calipers (usually a hair under). This device also uses M3, so measure each screw rather than assuming they match.
3. Pitch: 0.4 mm from one thread crest to the next (25 crests per centimetre). A thread pitch gauge or the pitch-gauge tool settles it in seconds.
4. Length: for shoulder screw screws, measure from under the head to the tip (countersunk heads are the exception: they are measured overall).
5. The records span 3–15 mm, which means different positions take different lengths — match each hole to its own screw.
6. Driver: the source names a Phillips drive. For comparison, standard M2 heads take PH0 (Phillips) or T6 (Torx), or a 1.5 mm hex key.
7. Tightening: no device-specific torque is published in these records. The site's general figure for M2 is about 25-40 N·cm into metal threads and 12-20 N·cm into plastic bosses; snug it up and stop.

Pitch gauge · Screw size finder · Torque guide

More in Laptops & PCs

The same screw also fits

Devices whose records share a thread with HP Compaq Presario R4000, closest length match first.

• HP EliteBook 840 14 inch G11 also M2 × 4 mm
• Lenovo ThinkPad SL500c also M2 × 15 mm
• Lenovo LOQ 15IAX9I, and Lenovo LOQ 15IRX9 also M2 × 3 mm
• Acer Aspire 7745G also M2 × 3 mm
• Lenovo ideapad 100S-14IBR also M2 × 4 mm
• Lenovo ideapad 330L-17IKB also M2 × 3 mm
• Lenovo B330S-14IKBR also M2 × 3 mm
• Lenovo ThinkPad R40 also M2 × 4 mm

Questions about HP Compaq Presario R4000 screws

What size screw does HP Compaq Presario R4000 use?

M2 × 11 mm for heat sink (qty 4, shoulder, Phillips); M2 × 15 mm for display (qty 13, Phillips); M2 × 15 mm for keyboard (qty 4, Phillips); M2 × 15 mm for unspecified (qty 10, Phillips); M2 × 3 mm for palm rest (qty 2, Phillips); M2 × 4 mm for fan (qty 3, Phillips); M2 × 4 mm for keyboard (qty 4, Phillips); M2 × 4 mm for speaker (qty 2, Phillips); M2 × 4 mm for unspecified (Phillips); M2 × 7 mm for chassis/frame (qty 6, Phillips); M2 × 7 mm for display (qty 4, Phillips); M2 × 7 mm for hard drive (qty 2, Phillips); M2 × 7 mm for memory (Phillips); M2 × 7 mm for optical drive (Phillips); M2 × 7 mm for system board (qty 4, Phillips); M2 × 7 mm for unspecified (qty 5, Phillips); M3 × 4.5 mm for .

How long are the screws in HP Compaq Presario R4000?

The records range from 3 to 15 mm depending on the position, so match each screw to its own hole.

What is the thread pitch of an M2 screw?

0.4 mm (coarse), which is the standard pitch for M2 machine screws; a 0.25 mm fine pitch exists but is uncommon. The tap drill is 1.6 mm and the normal clearance hole is 2.4 mm.

What screwdriver do I need for HP Compaq Presario R4000?

The source lists a Phillips drive. Standard M2 heads otherwise take PH0 (Phillips) or T6 (Torx), or a 1.5 mm hex key.

Can I use an imperial screw instead of M2?

No. Imperial look-alike: #2-56 UNC (2.18 mm) is close but not interchangeable. Use a true M2 screw so it does not cross-thread or strip the hole.

Where can I buy replacement screws for HP Compaq Presario R4000?

TechSpareWarehouse (our own store) lists M2 x 3mm and M2 x 4mm, which match lengths in the records above.