HP Elite x360 14 inch G11 screw size
M2 / M2.5 · 2.4 to 4.9 mm long
If you are replacing a screw on HP Elite x360 14 inch G11, the thread is M2 and M2.5 in lengths from 2.4 to 4.9 mm.
There are 6 separate fitment records for it, including speaker (qty 6, broadhead, Phillips) (M2), SSD (qty 1, Phillips) (M2) and touchpad (qty 3, broadhead, Phillips) (M2), plus 3 more in the table below.
Head and drive, as the sources state them: Phillips drive.
6 of the 6 records are marked confirmed, drawn from 1 source (kaas.hpcloud.hp.com).
An M2 screw is 2 mm in diameter with a 0.4 mm pitch, tapped with a 1.6 mm drill; imperial look-alike: #2-56 UNC (2.18 mm) is close but not interchangeable.
HP Elite x360 14 inch G11 screw specifications
One row per fitment record. Head, drive are shown only where the source states them; pitch is the ISO coarse pitch for the thread.
| Thread | Length | Pitch | Head | Drive | Where it goes | Status |
|---|---|---|---|---|---|---|
| M2 | 2.4 mm | 0.4 mm | not stated | Phillips | Speaker (qty 6, broadhead, Phillips) | Confirmed |
| M2 | 2.4 mm | 0.4 mm | not stated | Phillips | SSD (qty 1, Phillips) | Confirmed |
| M2 | 2.4 mm | 0.4 mm | not stated | Phillips | Touchpad (qty 3, broadhead, Phillips) | Confirmed |
| M2 | 2.4 mm | 0.4 mm | not stated | Phillips | Wireless card (qty 1, Phillips) | Confirmed |
| M2 | 4.9 mm | 0.4 mm | not stated | Phillips | System board (qty 12, Phillips) | Confirmed |
| M2.5 | 4.1 mm | 0.45 mm | not stated | Phillips | Display (qty 6, Phillips) | Confirmed |
Fitment records and sources
Speaker (qty 6, broadhead, Phillips)
pitch 0.4 mm · tap 1.6 mm · clearance 2.4 mm · PH0 / Torx T6
SSD (qty 1, Phillips)
pitch 0.4 mm · tap 1.6 mm · clearance 2.4 mm · PH0 / Torx T6
Touchpad (qty 3, broadhead, Phillips)
pitch 0.4 mm · tap 1.6 mm · clearance 2.4 mm · PH0 / Torx T6
Wireless card (qty 1, Phillips)
pitch 0.4 mm · tap 1.6 mm · clearance 2.4 mm · PH0 / Torx T6
System board (qty 12, Phillips)
pitch 0.4 mm · tap 1.6 mm · clearance 2.4 mm · PH0 / Torx T6
Display (qty 6, Phillips)
pitch 0.45 mm · tap 2.05 mm · clearance 2.9 mm · PH1 / Torx T8
How to check the screw before you buy
- Laptop covers and brackets often mix two or three lengths of the same thread, so lay the screws out in the order they came out (a magnetic mat or a sheet of paper with the hole pattern drawn on it works).
- Diameter: across the threads an M2 screw measures about 2 mm with calipers (usually a hair under). This device also uses M2.5, so measure each screw rather than assuming they match.
- Pitch: 0.4 mm from one thread crest to the next (25 crests per centimetre). A thread pitch gauge or the pitch-gauge tool settles it in seconds.
- Length: measure from under the head to the tip for pan, button, wafer and cap heads; countersunk (flat) heads are measured overall.
- The records span 2.4–4.9 mm, which means different positions take different lengths — match each hole to its own screw.
- Driver: the source names a Phillips drive. For comparison, standard M2 heads take PH0 (Phillips) or T6 (Torx), or a 1.5 mm hex key.
- Tightening: no device-specific torque is published in these records. The site's general figure for M2 is about 25-40 N·cm into metal threads and 12-20 N·cm into plastic bosses; snug it up and stop.
Common mix-ups with M2 / M2.5
- The standard M.2 SSD screw is M2 x 3mm, but some laptops and handhelds use non-standard lengths or head shapes.
- M.2 SSD mounting screws (M2 x 3mm) are frequently mislabeled generically as 'M.2 screws' which can be confused with the M2 metric thread designation — they do coincide numerically here but are conceptually distinct (M.2 = card format, M2 = thread size).
- M2.5 pitch is 0.45mm vs M3's 0.5mm and M2's 0.4mm — forcing the wrong one strips plastic bosses instantly.
- M2.5 and M3 look the same to the naked eye — you need calipers on the shank to tell them apart.
Buy these screws at TechSpare Warehouse
In stock and shipped from South Carolina. Our black screws are Phillips wafer head (low profile); match the head style and length to the original before you order.
-
M2 x 2.5mm Screws for Dell XPS 14 9440 M.2 SSD Drive – 10-Pack Black
$4.99 -
M2 x 2.5mm Screws for ASUS ROG Strix G17 G713 SSD WiFi Touchpad 10-Pack Black
$4.99
-
M2 x 5mm Replacement Bottom Case Screws for Dell Inspiron 3535 Laptop 10-Pack
$4.99 -
M2 x 5mm Phillips Wafer Head Screw for Dell G16 7630 Gaming Laptop Repair - Pack of 100 Black
$7.99 -
M2.5 x 4mm Screws for Lenovo IdeaPad 5 Pro 14 Display Hinge 10-Pack Black
$4.99 -
M2.5 x 4mm Screws for Lenovo IdeaPad 5 Pro 14 System Board Hinge 10-Pack Black
$4.99
-
ASUS ROG Strix G15 G513R Replacement Screws Sold Individually – M1.6 x 3mm, M2 x 2.5mm, M2 x 3mm, M2.5 x 6mm Phillips Wafer Head, Black
$0.10Choose size -
ASUS ROG Strix G17 G713 Replacement Screws Sold Individually – M1.6 x 3mm, M2 x 2.5mm, M2 x 3mm, M2.5 x 6mm Phillips Wafer Head, Black
$0.10Choose size
More in Laptops & PCs
The same screw also fits
Devices whose records share a thread with HP Elite x360 14 inch G11, closest length match first.
- Lenovo ThinkPad 560E also M2 × 2.4 mm
- Lenovo ThinkPad E565 also M2 × 2.4 mm
- HP 240 G5 also M2 × 2.4 mm
- HP 240 G4 also M2 × 2.4 mm
- Lenovo IdeaPad Z400 also M2 × 4.9 mm
- Lenovo ThinkPad E560 also M2 × 2.4 mm
- Lenovo ThinkPad E550c also M2 × 2.4 mm
- HP 13-4100 through 4199) also M2.5 × 4.1 mm
Questions about HP Elite x360 14 inch G11 screws
- What size screw does HP Elite x360 14 inch G11 use?
- M2 × 2.4 mm for speaker (qty 6, broadhead, Phillips); M2 × 2.4 mm for SSD (qty 1, Phillips); M2 × 2.4 mm for touchpad (qty 3, broadhead, Phillips); M2 × 2.4 mm for wireless card (qty 1, Phillips); M2 × 4.9 mm for system board (qty 12, Phillips); M2.5 × 4.1 mm for display (qty 6, Phillips).
- How long are the screws in HP Elite x360 14 inch G11?
- The records range from 2.4 to 4.9 mm depending on the position, so match each screw to its own hole.
- What is the thread pitch of an M2 screw?
- 0.4 mm (coarse), which is the standard pitch for M2 machine screws; a 0.25 mm fine pitch exists but is uncommon. The tap drill is 1.6 mm and the normal clearance hole is 2.4 mm.
- What screwdriver do I need for HP Elite x360 14 inch G11?
- The source lists a Phillips drive. Standard M2 heads otherwise take PH0 (Phillips) or T6 (Torx), or a 1.5 mm hex key.
- Can I use an imperial screw instead of M2?
- No. Imperial look-alike: #2-56 UNC (2.18 mm) is close but not interchangeable. Use a true M2 screw so it does not cross-thread or strip the hole.
- Where can I buy replacement screws for HP Elite x360 14 inch G11?
- TechSpareWarehouse (our own store) lists M2 x 2.5mm, M2 x 5mm and M2.5 x 4mm, which match lengths in the records above.