HP EliteBook Revolve 810 G1 screw size

HP EliteBook Revolve 810 G1 screw specifications

One row per fitment record. Head, drive are shown only where the source states them; pitch is the ISO coarse pitch for the thread.

How to check the screw before you buy

1. A screw that is even 1 mm too long in a laptop base can push into the keyboard, battery or a board trace, so match the length position by position.
2. Diameter: across the threads an M2 screw measures about 2 mm with calipers (usually a hair under). If yours measures noticeably more or less, it is a different thread.
3. Pitch: 0.4 mm from one thread crest to the next (25 crests per centimetre). A thread pitch gauge or the pitch-gauge tool settles it in seconds.
4. Length: measure from under the head to the tip for pan, button, wafer and cap heads; countersunk (flat) heads are measured overall.
5. The records span 2.5–8.5 mm, which means different positions take different lengths — match each hole to its own screw.
6. Driver: the source names a Torx T8 drive. For comparison, standard M2 heads take PH0 (Phillips) or T6 (Torx), or a 1.5 mm hex key.
7. Tightening: no device-specific torque is published in these records. The site's general figure for M2 is about 25-40 N·cm into metal threads and 12-20 N·cm into plastic bosses; snug it up and stop.

Pitch gauge · Screw size finder · Torque guide

More in Laptops & PCs

The same screw also fits

Devices whose records share a thread with HP EliteBook Revolve 810 G1, closest length match first.

• Lenovo V4400u also M2 × 2.5 mm
• Dell Precision M2300 also M2 × 3 mm
• Lenovo ThinkPad X121e also M2 × 3 mm
• Toshiba Satellite M20 also M2 × 3 mm
• Lenovo ThinkPad T16 Gen 4 also M2 × 2.5 mm
• Acer Extensa 5610 also M2 × 3 mm
• Dell Precision 5750 also M2 × 6.5 mm
• HP ProBook 645 G1 also M2 × 3 mm

Questions about HP EliteBook Revolve 810 G1 screws

What size screw does HP EliteBook Revolve 810 G1 use?

M2 × 2.5 mm for base cover (qty 1, Torx T8); M2 × 2.5 mm for hinge (qty 6, Phillips); M2 × 2.5 mm for system board (qty 1, Phillips); M2 × 3 mm for speaker (qty 3, broadhead, Phillips); M2 × 3 mm for SSD (qty 1, Phillips); M2 × 3 mm for unspecified (qty 1, Phillips); M2 × 3 mm for wireless card (qty 1, Phillips); M2 × 4.3 mm for base cover (qty 2, Phillips); M2 × 5 mm for display (qty 2, Phillips); M2 × 5.65 mm for base cover (qty 5, Torx T8); M2 × 6.5 mm for fan (qty 4, captive, Phillips); M2 × 6.5 mm for unspecified (qty 2, Phillips); M2 × 8.5 mm for unspecified (qty 2, Phillips).

How long are the screws in HP EliteBook Revolve 810 G1?

The records range from 2.5 to 8.5 mm depending on the position, so match each screw to its own hole.

What is the thread pitch of an M2 screw?

0.4 mm (coarse), which is the standard pitch for M2 machine screws; a 0.25 mm fine pitch exists but is uncommon. The tap drill is 1.6 mm and the normal clearance hole is 2.4 mm.

What screwdriver do I need for HP EliteBook Revolve 810 G1?

The source lists a Torx T8 and Phillips drive. Standard M2 heads otherwise take PH0 (Phillips) or T6 (Torx), or a 1.5 mm hex key.

Can I use an imperial screw instead of M2?

No. Imperial look-alike: #2-56 UNC (2.18 mm) is close but not interchangeable. Use a true M2 screw so it does not cross-thread or strip the hole.

Where can I buy replacement screws for HP EliteBook Revolve 810 G1?

TechSpareWarehouse (our own store) lists M2 x 2.5mm, M2 x 3mm and M2 x 5mm, which match lengths in the records above.