HP ENVY 13-d1xx screw size
M2 / M2.5 · 2.3 to 5.5 mm long
Our records put HP ENVY 13-d1xx on M2 and M2.5 screws in lengths from 2.3 to 5.5 mm.
There are 20 separate fitment records for it, including base cover (qty 4, Phillips) (M2), display (qty 4, Phillips) (M2) and heat sink (qty 3, Phillips) (M2), plus 17 more in the table below.
Head and drive, as the sources state them: Phillips drive.
20 of the 20 records are marked confirmed, drawn from 1 source (h10032.www1.hp.com).
For reference, M2 is 2 mm across the threads at 0.4 mm pitch. The imperial size people confuse it with: #2-56 UNC (2.18 mm) is close but not interchangeable.
HP ENVY 13-d1xx screw specifications
One row per fitment record. Head, drive are shown only where the source states them; pitch is the ISO coarse pitch for the thread.
| Thread | Length | Pitch | Head | Drive | Where it goes | Status |
|---|---|---|---|---|---|---|
| M2 | 2.3 mm | 0.4 mm | not stated | Phillips | Base cover (qty 4, Phillips) | Confirmed |
| M2 | 2.3 mm | 0.4 mm | not stated | Phillips | Display (qty 4, Phillips) | Confirmed |
| M2 | 2.4 mm | 0.4 mm | not stated | Phillips | Heat sink (qty 3, Phillips) | Confirmed |
| M2 | 2.4 mm | 0.4 mm | not stated | Phillips | Hinge (qty 2, Phillips) | Confirmed |
| M2 | 2.5 mm | 0.4 mm | not stated | Phillips | Power button (qty 2, Phillips) | Confirmed |
| M2 | 2.5 mm | 0.4 mm | not stated | Phillips | Touchpad (qty 9, Phillips) | Confirmed |
| M2 | 2.6 mm | 0.4 mm | not stated | Phillips | SSD (qty 1, broadhead, Phillips) | Confirmed |
| M2 | 4.4 mm | 0.4 mm | not stated | Phillips | Bracket (qty 2, Phillips) | Confirmed |
| M2.5 | 2.6 mm | 0.45 mm | not stated | Phillips | Battery (qty 2, broadhead, Phillips) | Confirmed |
| M2.5 | 2.7 mm | 0.45 mm | not stated | Phillips | Hinge (qty 6, broadhead, Phillips) | Confirmed |
| M2.5 | 2.9 mm | 0.45 mm | not stated | Phillips | Display (qty 2, broadhead, Phillips) | Confirmed |
| M2.5 | 3.4 mm | 0.45 mm | not stated | Phillips | Base cover (qty 3, Phillips) | Confirmed |
| M2.5 | 3.4 mm | 0.45 mm | not stated | Phillips | Display bezel (qty 2, Phillips) | Confirmed |
| M2.5 | 3.4 mm | 0.45 mm | not stated | Phillips | System board (qty 1, Phillips) | Confirmed |
| M2.5 | 4.4 mm | 0.45 mm | not stated | Phillips | Battery (qty 4, Phillips) | Confirmed |
| M2.5 | 4.4 mm | 0.45 mm | not stated | Phillips | Bracket (qty 1, Phillips) | Confirmed |
| M2.5 | 4.4 mm | 0.45 mm | not stated | Phillips | Display (qty 3, Phillips) | Confirmed |
| M2.5 | 4.4 mm | 0.45 mm | not stated | Phillips | Fan (qty 2, Phillips) | Confirmed |
| M2.5 | 4.4 mm | 0.45 mm | not stated | Phillips | System board (qty 1, Phillips) | Confirmed |
| M2.5 | 5.5 mm | 0.45 mm | not stated | Phillips | Base cover (qty 8, Phillips) | Confirmed |
Fitment records and sources
Base cover (qty 4, Phillips)
pitch 0.4 mm · tap 1.6 mm · clearance 2.4 mm · PH0 / Torx T6
Display (qty 4, Phillips)
pitch 0.4 mm · tap 1.6 mm · clearance 2.4 mm · PH0 / Torx T6
Heat sink (qty 3, Phillips)
pitch 0.4 mm · tap 1.6 mm · clearance 2.4 mm · PH0 / Torx T6
Hinge (qty 2, Phillips)
pitch 0.4 mm · tap 1.6 mm · clearance 2.4 mm · PH0 / Torx T6
Power button (qty 2, Phillips)
pitch 0.4 mm · tap 1.6 mm · clearance 2.4 mm · PH0 / Torx T6
Touchpad (qty 9, Phillips)
pitch 0.4 mm · tap 1.6 mm · clearance 2.4 mm · PH0 / Torx T6
SSD (qty 1, broadhead, Phillips)
pitch 0.4 mm · tap 1.6 mm · clearance 2.4 mm · PH0 / Torx T6
Bracket (qty 2, Phillips)
pitch 0.4 mm · tap 1.6 mm · clearance 2.4 mm · PH0 / Torx T6
Battery (qty 2, broadhead, Phillips)
pitch 0.45 mm · tap 2.05 mm · clearance 2.9 mm · PH1 / Torx T8
Hinge (qty 6, broadhead, Phillips)
pitch 0.45 mm · tap 2.05 mm · clearance 2.9 mm · PH1 / Torx T8
Display (qty 2, broadhead, Phillips)
pitch 0.45 mm · tap 2.05 mm · clearance 2.9 mm · PH1 / Torx T8
Base cover (qty 3, Phillips)
pitch 0.45 mm · tap 2.05 mm · clearance 2.9 mm · PH1 / Torx T8
Display bezel (qty 2, Phillips)
pitch 0.45 mm · tap 2.05 mm · clearance 2.9 mm · PH1 / Torx T8
System board (qty 1, Phillips)
pitch 0.45 mm · tap 2.05 mm · clearance 2.9 mm · PH1 / Torx T8
Battery (qty 4, Phillips)
pitch 0.45 mm · tap 2.05 mm · clearance 2.9 mm · PH1 / Torx T8
Bracket (qty 1, Phillips)
pitch 0.45 mm · tap 2.05 mm · clearance 2.9 mm · PH1 / Torx T8
Display (qty 3, Phillips)
pitch 0.45 mm · tap 2.05 mm · clearance 2.9 mm · PH1 / Torx T8
Fan (qty 2, Phillips)
pitch 0.45 mm · tap 2.05 mm · clearance 2.9 mm · PH1 / Torx T8
System board (qty 1, Phillips)
pitch 0.45 mm · tap 2.05 mm · clearance 2.9 mm · PH1 / Torx T8
Base cover (qty 8, Phillips)
pitch 0.45 mm · tap 2.05 mm · clearance 2.9 mm · PH1 / Torx T8
How to check the screw before you buy
- A screw that is even 1 mm too long in a laptop base can push into the keyboard, battery or a board trace, so match the length position by position.
- Diameter: across the threads an M2 screw measures about 2 mm with calipers (usually a hair under). This device also uses M2.5, so measure each screw rather than assuming they match.
- Pitch: 0.4 mm from one thread crest to the next (25 crests per centimetre). A thread pitch gauge or the pitch-gauge tool settles it in seconds.
- Length: measure from under the head to the tip for pan, button, wafer and cap heads; countersunk (flat) heads are measured overall.
- The records span 2.3–5.5 mm, which means different positions take different lengths — match each hole to its own screw.
- Driver: the source names a Phillips drive. For comparison, standard M2 heads take PH0 (Phillips) or T6 (Torx), or a 1.5 mm hex key.
- Tightening: no device-specific torque is published in these records. The site's general figure for M2 is about 25-40 N·cm into metal threads and 12-20 N·cm into plastic bosses; snug it up and stop.
Common mix-ups with M2 / M2.5
- The standard M.2 SSD screw is M2 x 3mm, but some laptops and handhelds use non-standard lengths or head shapes.
- M2 (2.00mm, 0.4mm pitch) is NOT the same as #2-56 UNC (2.18mm) — close enough to cross-thread and strip if forced.
- M2.5 pitch is 0.45mm vs M3's 0.5mm and M2's 0.4mm — forcing the wrong one strips plastic bosses instantly.
- M2.5 and M3 look the same to the naked eye — you need calipers on the shank to tell them apart.
Buy these screws at TechSpare Warehouse
In stock and shipped from South Carolina. Our black screws are Phillips wafer head (low profile); match the head style and length to the original before you order.
-
M2 x 2.5mm Screws for Dell XPS 14 9440 M.2 SSD Drive – 10-Pack Black
$4.99 -
M2 x 2.5mm Screws for ASUS ROG Strix G17 G713 SSD WiFi Touchpad 10-Pack Black
$4.99
-
25x M2.5 x 3mm Phillips Screws for Acer Nitro 5 SSD M.2 WiFi Card
$5.99 -
ASUS ROG Strix G15 G513R Replacement Screws Sold Individually – M1.6 x 3mm, M2 x 2.5mm, M2 x 3mm, M2.5 x 6mm Phillips Wafer Head, Black
$0.10Choose size -
ASUS ROG Strix G17 G713 Replacement Screws Sold Individually – M1.6 x 3mm, M2 x 2.5mm, M2 x 3mm, M2.5 x 6mm Phillips Wafer Head, Black
$0.10Choose size
-
Dell Latitude 5430 Replacement Screws Sold Individually – M2 x 2.5mm, M2 x 3mm, M2 x 5mm, M2.5 x 5mm Phillips Wafer Head, Black
$0.10Choose size -
HP EliteBook 840 G8 Replacement Screws Sold Individually – M1.6 x 3mm, M2 x 2.5mm, M2 x 4mm, M2.5 x 4mm Phillips Wafer Head, Black
$0.10Choose size
More in Laptops & PCs
The same screw also fits
Devices whose records share a thread with HP ENVY 13-d1xx, closest length match first.
- HP OMEN 17.3 inch Gaming 17-ck0000 also M2 × 2.5 mm
- Lenovo IdeaPad S210 Touch also M2 × 2.5 mm
- Lenovo ThinkPad E490s also M2 × 2.5 mm
- Lenovo ThinkPad T590 also M2 × 2.5 mm
- Lenovo ideapad 720-15IKB also M2 × 2.5 mm
- Lenovo ideapad 500S-14ISK also M2 × 2.5 mm
- Lenovo ThinkPad T15p Gen 1 also M2 × 2.3 mm
- HP EliteBook x360 1030 G3 also M2 × 2.4 mm
Questions about HP ENVY 13-d1xx screws
- What size screw does HP ENVY 13-d1xx use?
- M2 × 2.3 mm for base cover (qty 4, Phillips); M2 × 2.3 mm for display (qty 4, Phillips); M2 × 2.4 mm for heat sink (qty 3, Phillips); M2 × 2.4 mm for hinge (qty 2, Phillips); M2 × 2.5 mm for power button (qty 2, Phillips); M2 × 2.5 mm for touchpad (qty 9, Phillips); M2 × 2.6 mm for SSD (qty 1, broadhead, Phillips); M2 × 4.4 mm for bracket (qty 2, Phillips); M2.5 × 2.6 mm for battery (qty 2, broadhead, Phillips); M2.5 × 2.7 mm for hinge (qty 6, broadhead, Phillips); M2.5 × 2.9 mm for display (qty 2, broadhead, Phillips); M2.5 × 3.4 mm for base cover (qty 3, Phillips); M2.5 × 3.4 mm for display bezel (qty 2, Phillips); M2.5 × 3.4 mm for system board (qty 1, Phillips); M2.5 × 4.4 mm for battery.
- How long are the screws in HP ENVY 13-d1xx?
- The records range from 2.3 to 5.5 mm depending on the position, so match each screw to its own hole.
- What is the thread pitch of an M2 screw?
- 0.4 mm (coarse), which is the standard pitch for M2 machine screws; a 0.25 mm fine pitch exists but is uncommon. The tap drill is 1.6 mm and the normal clearance hole is 2.4 mm.
- What screwdriver do I need for HP ENVY 13-d1xx?
- The source lists a Phillips drive. Standard M2 heads otherwise take PH0 (Phillips) or T6 (Torx), or a 1.5 mm hex key.
- Can I use an imperial screw instead of M2?
- No. Imperial look-alike: #2-56 UNC (2.18 mm) is close but not interchangeable. Use a true M2 screw so it does not cross-thread or strip the hole.
- Where can I buy replacement screws for HP ENVY 13-d1xx?
- TechSpareWarehouse (our own store) lists M2 x 2.5mm and M2.5 x 3mm, which match lengths in the records above.