HP ENVY 17-cg1000 (ids 32552529 screw size

HP ENVY 17-cg1000 (ids 32552529 screw specifications

One row per fitment record. Head, drive are shown only where the source states them; pitch is the ISO coarse pitch for the thread.

How to check the screw before you buy

1. Laptop covers and brackets often mix two or three lengths of the same thread, so lay the screws out in the order they came out (a magnetic mat or a sheet of paper with the hole pattern drawn on it works).
2. Diameter: across the threads an M1.6 screw measures about 1.6 mm with calipers (usually a hair under). This device also uses M2 / M2.5, so measure each screw rather than assuming they match.
3. Pitch: 0.35 mm from one thread crest to the next (28.57 crests per centimetre). A thread pitch gauge or the pitch-gauge tool settles it in seconds.
4. Length: measure from under the head to the tip for pan, button, wafer and cap heads; countersunk (flat) heads are measured overall.
5. The records span 2–8.5 mm, which means different positions take different lengths — match each hole to its own screw.
6. Driver: the source names a Phillips drive. For comparison, standard M1.6 heads take PH00 (Phillips) or T4–T5 (Torx), or a 1.5 mm hex key.
7. Tightening: no device-specific torque is published in these records. The site's general figure for M1.6 is about 12-20 N·cm into metal threads and 6-10 N·cm into plastic bosses; snug it up and stop.

Pitch gauge · Screw size finder · Torque guide

More in Laptops & PCs

The same screw also fits

Devices whose records share a thread with HP ENVY 17-cg1000 (ids 32552529, closest length match first.

• Lenovo ThinkPad T61p (14.1-inch) also M2 × 3 mm
• Dell Inspiron 15 5570 also M2 × 3 mm
• Dell Inspiron 510m also M2 × 3 mm
• Dell Vostro 14 3480 also M2 × 3 mm
• Dell Inspiron 15 3585 also M2 × 3 mm
• Acer Emachines EM250 also M2 × 3 mm
• Dell Pro 14 PC14250 also M2 × 3 mm
• Dell XPS 13 9310 also M1.6 × 2 mm

Questions about HP ENVY 17-cg1000 (ids 32552529 screws

What size screw does HP ENVY 17-cg1000 (ids 32552529 use?

M1.6 × 2 mm for touchpad (qty 4, Phillips); M1.6 × 2.5 mm for touchpad (qty 3, broadhead, Phillips); M2 × 2.5 mm for battery (qty 4, Phillips); M2 × 3 mm for I/O board (qty 1, Phillips); M2 × 3 mm for base cover (qty 2); M2 × 3 mm for battery (qty 4, Phillips); M2 × 3 mm for hard drive (qty 4, Phillips); M2 × 3 mm for heat sink (qty 6, Phillips); M2 × 3 mm for hinge (qty 2, Phillips); M2 × 3 mm for SSD (qty 1, Phillips); M2 × 3 mm for system board (qty 4, Phillips); M2 × 3 mm for unspecified (qty 1); M2 × 3 mm for wireless card (qty 1, Phillips); M2.5 × 2.5 mm for hard drive (qty 4); M2.5 × 6 mm for fan (qty 2, Phillips); M2.5 × 8.5 mm for base cover (qty 7, Phillips).

How long are the screws in HP ENVY 17-cg1000 (ids 32552529?

The records range from 2 to 8.5 mm depending on the position, so match each screw to its own hole.

What is the thread pitch of an M1.6 screw?

0.35 mm (coarse), which is the standard pitch for M1.6 machine screws; a 0.2 mm fine pitch exists but is uncommon. The tap drill is 1.25 mm and the normal clearance hole is 1.8 mm.

What screwdriver do I need for HP ENVY 17-cg1000 (ids 32552529?

The source lists a Phillips drive. Standard M1.6 heads otherwise take PH00 (Phillips) or T4–T5 (Torx), or a 1.5 mm hex key.

Can I use an imperial screw instead of M1.6?

No. Imperial look-alike: #1-72 UNF (1.85 mm) is larger; there is no true imperial equivalent. Use a true M1.6 screw so it does not cross-thread or strip the hole.

Where can I buy replacement screws for HP ENVY 17-cg1000 (ids 32552529?

TechSpareWarehouse (our own store) lists M2 x 2.5mm, M2 x 3mm and M2.5 x 6mm, which match lengths in the records above.