HP G3000 screw size
M2 / M2.5 / M3 · 4 to 13 mm long
If you are replacing a screw on HP G3000, the thread is M2, M2.5 and M3 in lengths from 4 to 13 mm.
There are 23 separate fitment records for it, including fan (Phillips) (M2), hinge (qty 4, Phillips) (M2) and optical drive (qty 2, Phillips) (M2), plus 20 more in the table below.
Head and drive, as the sources state them: Phillips drive.
23 of the 23 records are marked confirmed, drawn from 1 source (tim.id.au).
M2 means a 2 mm nominal diameter with a 0.4 mm thread pitch. Imperial look-alike: #2-56 UNC (2.18 mm) is close but not interchangeable.
HP G3000 screw specifications
One row per fitment record. Head, drive are shown only where the source states them; pitch is the ISO coarse pitch for the thread.
| Thread | Length | Pitch | Head | Drive | Where it goes | Status |
|---|---|---|---|---|---|---|
| M2 | 4 mm | 0.4 mm | not stated | Phillips | Fan (Phillips) | Confirmed |
| M2 | 4 mm | 0.4 mm | not stated | Phillips | Hinge (qty 4, Phillips) | Confirmed |
| M2 | 4 mm | 0.4 mm | not stated | Phillips | Optical drive (qty 2, Phillips) | Confirmed |
| M2 | 4 mm | 0.4 mm | not stated | Phillips | Wireless card (qty 2, Phillips) | Confirmed |
| M2.5 | 13 mm | 0.45 mm | not stated | Phillips | Display (qty 2, Phillips) | Confirmed |
| M2.5 | 13 mm | 0.45 mm | not stated | Phillips | Unspecified (qty 11, Phillips) | Confirmed |
| M2.5 | 4 mm | 0.45 mm | not stated | Phillips | Touchpad (qty 4, silver, Phillips) | Confirmed |
| M2.5 | 5 mm | 0.45 mm | not stated | Phillips | LED board (qty 2, Phillips) | Confirmed |
| M2.5 | 5 mm | 0.45 mm | not stated | Phillips | Display (qty 4, Phillips) | Confirmed |
| M2.5 | 5 mm | 0.45 mm | not stated | Phillips | Hard drive (qty 2, captive, Phillips)captive | Confirmed |
| M2.5 | 5 mm | 0.45 mm | not stated | Phillips | Hinge (qty 2, Phillips) | Confirmed |
| M2.5 | 5 mm | 0.45 mm | not stated | Phillips | Keyboard (qty 4, Phillips) | Confirmed |
| M2.5 | 5 mm | 0.45 mm | not stated | Phillips | Memory (captive, Phillips)captive | Confirmed |
| M2.5 | 5 mm | 0.45 mm | not stated | Phillips | Optical drive (qty 2, Phillips) | Confirmed |
| M2.5 | 5 mm | 0.45 mm | not stated | Phillips | System board (qty 2, Phillips) | Confirmed |
| M2.5 | 5 mm | 0.45 mm | not stated | Phillips | Touchpad (qty 4, Phillips) | Confirmed |
| M2.5 | 5 mm | 0.45 mm | not stated | Phillips | Unspecified (qty 2, Phillips) | Confirmed |
| M2.5 | 5 mm | 0.45 mm | not stated | Phillips | Wireless card (Phillips) | Confirmed |
| M2.5 | 7 mm | 0.45 mm | not stated | Phillips | Display bezel (qty 6, Phillips) | Confirmed |
| M2.5 | 7 mm | 0.45 mm | not stated | Phillips | Heat sink (qty 4, Phillips) | Confirmed |
| M2.5 | 9 mm | 0.45 mm | not stated | Phillips | Display (qty 4, Phillips) | Confirmed |
| M3 | 4 mm | 0.5 mm | not stated | Phillips | Hard drive (qty 4, Phillips) | Confirmed |
| M3 | 6 mm | 0.5 mm | not stated | Phillips | Fan (qty 2, Phillips) | Confirmed |
Fitment records and sources
Fan (Phillips)
pitch 0.4 mm · tap 1.6 mm · clearance 2.4 mm · PH0 / Torx T6
Hinge (qty 4, Phillips)
pitch 0.4 mm · tap 1.6 mm · clearance 2.4 mm · PH0 / Torx T6
Optical drive (qty 2, Phillips)
pitch 0.4 mm · tap 1.6 mm · clearance 2.4 mm · PH0 / Torx T6
Wireless card (qty 2, Phillips)
pitch 0.4 mm · tap 1.6 mm · clearance 2.4 mm · PH0 / Torx T6
Display (qty 2, Phillips)
pitch 0.45 mm · tap 2.05 mm · clearance 2.9 mm · PH1 / Torx T8
Unspecified (qty 11, Phillips)
pitch 0.45 mm · tap 2.05 mm · clearance 2.9 mm · PH1 / Torx T8
Touchpad (qty 4, silver, Phillips)
pitch 0.45 mm · tap 2.05 mm · clearance 2.9 mm · PH1 / Torx T8
LED board (qty 2, Phillips)
pitch 0.45 mm · tap 2.05 mm · clearance 2.9 mm · PH1 / Torx T8
Display (qty 4, Phillips)
pitch 0.45 mm · tap 2.05 mm · clearance 2.9 mm · PH1 / Torx T8
Hard drive (qty 2, captive, Phillips)
pitch 0.45 mm · tap 2.05 mm · clearance 2.9 mm · PH1 / Torx T8
Hinge (qty 2, Phillips)
pitch 0.45 mm · tap 2.05 mm · clearance 2.9 mm · PH1 / Torx T8
Keyboard (qty 4, Phillips)
pitch 0.45 mm · tap 2.05 mm · clearance 2.9 mm · PH1 / Torx T8
Memory (captive, Phillips)
pitch 0.45 mm · tap 2.05 mm · clearance 2.9 mm · PH1 / Torx T8
Optical drive (qty 2, Phillips)
pitch 0.45 mm · tap 2.05 mm · clearance 2.9 mm · PH1 / Torx T8
System board (qty 2, Phillips)
pitch 0.45 mm · tap 2.05 mm · clearance 2.9 mm · PH1 / Torx T8
Touchpad (qty 4, Phillips)
pitch 0.45 mm · tap 2.05 mm · clearance 2.9 mm · PH1 / Torx T8
Unspecified (qty 2, Phillips)
pitch 0.45 mm · tap 2.05 mm · clearance 2.9 mm · PH1 / Torx T8
Wireless card (Phillips)
pitch 0.45 mm · tap 2.05 mm · clearance 2.9 mm · PH1 / Torx T8
Display bezel (qty 6, Phillips)
pitch 0.45 mm · tap 2.05 mm · clearance 2.9 mm · PH1 / Torx T8
Heat sink (qty 4, Phillips)
pitch 0.45 mm · tap 2.05 mm · clearance 2.9 mm · PH1 / Torx T8
Display (qty 4, Phillips)
pitch 0.45 mm · tap 2.05 mm · clearance 2.9 mm · PH1 / Torx T8
Hard drive (qty 4, Phillips)
pitch 0.5 mm · tap 2.5 mm · clearance 3.4 mm · PH1 / Torx T10
Fan (qty 2, Phillips)
pitch 0.5 mm · tap 2.5 mm · clearance 3.4 mm · PH1 / Torx T10
How to check the screw before you buy
- Laptop covers and brackets often mix two or three lengths of the same thread, so lay the screws out in the order they came out (a magnetic mat or a sheet of paper with the hole pattern drawn on it works).
- Diameter: across the threads an M2 screw measures about 2 mm with calipers (usually a hair under). This device also uses M2.5 / M3, so measure each screw rather than assuming they match.
- Pitch: 0.4 mm from one thread crest to the next (25 crests per centimetre). A thread pitch gauge or the pitch-gauge tool settles it in seconds.
- Length: measure from under the head to the tip for pan, button, wafer and cap heads; countersunk (flat) heads are measured overall.
- The records span 4–13 mm, which means different positions take different lengths — match each hole to its own screw.
- Driver: the source names a Phillips drive. For comparison, standard M2 heads take PH0 (Phillips) or T6 (Torx), or a 1.5 mm hex key.
- Tightening: no device-specific torque is published in these records. The site's general figure for M2 is about 25-40 N·cm into metal threads and 12-20 N·cm into plastic bosses; snug it up and stop.
Common mix-ups with M2 / M2.5 / M3
- M.2 SSD mounting screws (M2 x 3mm) are frequently mislabeled generically as 'M.2 screws' which can be confused with the M2 metric thread designation — they do coincide numerically here but are conceptually distinct (M.2 = card format, M2 = thread size).
- M2.5 and M3 look the same to the naked eye — you need calipers on the shank to tell them apart.
- 3.5in desktop and enterprise hard drives are 6-32 UNC imperial, not M3 - only the 2.5in form factor is metric.
Buy these screws at TechSpare Warehouse
In stock and shipped from South Carolina. Our black screws are Phillips wafer head (low profile); match the head style and length to the original before you order.
-
M2 x 4mm Phillips Wafer Head Machine Screws Black 50-Pack Laptop SSD Repair
$4.49 each · min. 2
-
M2 x 4mm Screws for Dell Latitude 5530 SSD Type-C Bracket 10-Pack Black
$4.99
-
M2.5 x 4mm Screws for Lenovo IdeaPad 5 Pro 14 Display Hinge 10-Pack Black
$4.99 -
M2.5 x 4mm Screws for Lenovo IdeaPad 5 Pro 14 System Board Hinge 10-Pack Black
$4.99
-
M2.5 x 5mm Screws Compatible with Dell XPS 14 9440 Display Assembly 10-Pack
$4.99 -
M2.5 x 5mm Phillips Wafer Head Screw for Action Camera Protective Housing - Pack of 50 Black
$4.79 each · min. 2
-
ASUS ROG Strix G15 G513R Replacement Screws Sold Individually – M1.6 x 3mm, M2 x 2.5mm, M2 x 3mm, M2.5 x 6mm Phillips Wafer Head, Black
$0.10Choose size -
ASUS ROG Strix G17 G713 Replacement Screws Sold Individually – M1.6 x 3mm, M2 x 2.5mm, M2 x 3mm, M2.5 x 6mm Phillips Wafer Head, Black
$0.10Choose size
More in Laptops & PCs
The same screw also fits
Devices whose records share a thread with HP G3000, closest length match first.
- Dell Inspiron 16 5635 also M2 × 4 mm
- Lenovo V510-15IKB also M2 × 4 mm
- Dell Inspiron 16 5645 also M2.5 × 5 mm
- HP Spectre x360 16 inch 2-in-1 16-f0000 also M2 × 4 mm
- Lenovo ideapad 330L-15IKB also M2.5 × 5 mm
- Lenovo ThinkPad S340 also M2 × 4 mm
- HP 256R 15.6 inch G9 also M2 × 4 mm
- Dell G15 5530 also M2 × 4 mm
Questions about HP G3000 screws
- What size screw does HP G3000 use?
- M2 × 4 mm for fan (Phillips); M2 × 4 mm for hinge (qty 4, Phillips); M2 × 4 mm for optical drive (qty 2, Phillips); M2 × 4 mm for wireless card (qty 2, Phillips); M2.5 × 13 mm for display (qty 2, Phillips); M2.5 × 13 mm for unspecified (qty 11, Phillips); M2.5 × 4 mm for touchpad (qty 4, silver, Phillips); M2.5 × 5 mm for LED board (qty 2, Phillips); M2.5 × 5 mm for display (qty 4, Phillips); M2.5 × 5 mm for hard drive (qty 2, captive, Phillips); M2.5 × 5 mm for hinge (qty 2, Phillips); M2.5 × 5 mm for keyboard (qty 4, Phillips); M2.5 × 5 mm for memory (captive, Phillips); M2.5 × 5 mm for optical drive (qty 2, Phillips); M2.5 × 5 mm for system board (qty 2, Phillips); M2.5 × 5 mm for touchpa.
- How long are the screws in HP G3000?
- The records range from 4 to 13 mm depending on the position, so match each screw to its own hole.
- What is the thread pitch of an M2 screw?
- 0.4 mm (coarse), which is the standard pitch for M2 machine screws; a 0.25 mm fine pitch exists but is uncommon. The tap drill is 1.6 mm and the normal clearance hole is 2.4 mm.
- What screwdriver do I need for HP G3000?
- The source lists a Phillips drive. Standard M2 heads otherwise take PH0 (Phillips) or T6 (Torx), or a 1.5 mm hex key.
- Can I use an imperial screw instead of M2?
- No. Imperial look-alike: #2-56 UNC (2.18 mm) is close but not interchangeable. Use a true M2 screw so it does not cross-thread or strip the hole.
- Where can I buy replacement screws for HP G3000?
- TechSpareWarehouse (our own store) lists M2 x 4mm, M2.5 x 4mm and M2.5 x 5mm, which match lengths in the records above.