HP Mini 1000 screw size
M1.6 / M2 / M2.5 · 2.5 to 7 mm long
Our records put HP Mini 1000 on M1.6, M2 and M2.5 screws in lengths from 2.5 to 7 mm.
There are 24 separate fitment records for it, including heat sink (qty 2, Phillips) (M1.6), wireless card (qty 2, Phillips) (M1.6) and keyboard (Phillips) (M1.6), plus 21 more in the table below.
Head and drive, as the sources state them: Phillips drive.
24 of the 24 records are marked confirmed, drawn from 1 source (tim.id.au).
For reference, M1.6 is 1.6 mm across the threads at 0.35 mm pitch. The imperial size people confuse it with: #1-72 UNF (1.85 mm) is larger; there is no true imperial equivalent.
HP Mini 1000 screw specifications
One row per fitment record. Head, drive are shown only where the source states them; pitch is the ISO coarse pitch for the thread.
| Thread | Length | Pitch | Head | Drive | Where it goes | Status |
|---|---|---|---|---|---|---|
| M1.6 | 2.5 mm | 0.35 mm | not stated | Phillips | Heat sink (qty 2, Phillips) | Confirmed |
| M1.6 | 2.5 mm | 0.35 mm | not stated | Phillips | Wireless card (qty 2, Phillips) | Confirmed |
| M1.6 | 4 mm | 0.35 mm | not stated | Phillips | Keyboard (Phillips) | Confirmed |
| M1.6 | 4 mm | 0.35 mm | not stated | Phillips | Memory (qty 85, Phillips) | Confirmed |
| M1.6 | 6 mm | 0.35 mm | not stated | Phillips | Keyboard (Phillips) | Confirmed |
| M2 | 3 mm | 0.4 mm | not stated | Phillips | Bracket (qty 2, Phillips) | Confirmed |
| M2 | 3 mm | 0.4 mm | not stated | Phillips | Camera (qty 2, Phillips) | Confirmed |
| M2 | 3 mm | 0.4 mm | not stated | Phillips | Display (qty 9, Phillips) | Confirmed |
| M2 | 3 mm | 0.4 mm | not stated | Phillips | Fan (Phillips) | Confirmed |
| M2 | 3 mm | 0.4 mm | not stated | Phillips | Memory (qty 89, Phillips) | Confirmed |
| M2 | 3 mm | 0.4 mm | not stated | Phillips | SSD (qty 3, Phillips) | Confirmed |
| M2 | 3 mm | 0.4 mm | not stated | Phillips | Wireless card (Phillips) | Confirmed |
| M2 | 4.5 mm | 0.4 mm | not stated | Phillips | Bracket (qty 2, Phillips) | Confirmed |
| M2 | 4.5 mm | 0.4 mm | not stated | Phillips | Fan (Phillips) | Confirmed |
| M2 | 4.5 mm | 0.4 mm | not stated | Phillips | Hard drive (qty 2, Phillips) | Confirmed |
| M2 | 4.5 mm | 0.4 mm | not stated | Phillips | Hinge (qty 2, Phillips) | Confirmed |
| M2 | 4.5 mm | 0.4 mm | not stated | Phillips | Palm rest (Phillips) | Confirmed |
| M2 | 4.5 mm | 0.4 mm | not stated | Phillips | Speaker (qty 2, Phillips) | Confirmed |
| M2 | 4.5 mm | 0.4 mm | not stated | Phillips | System board (Phillips) | Confirmed |
| M2 | 4.5 mm | 0.4 mm | not stated | Phillips | Unspecified (qty 91, Phillips) | Confirmed |
| M2.5 | 5 mm | 0.45 mm | not stated | Phillips | Display (qty 3, Phillips) | Confirmed |
| M2.5 | 5 mm | 0.45 mm | not stated | Phillips | Palm rest (qty 5, Phillips) | Confirmed |
| M2.5 | 5 mm | 0.45 mm | not stated | Phillips | Unspecified (qty 93, Phillips) | Confirmed |
| M2.5 | 7 mm | 0.45 mm | not stated | Phillips | Palm rest (qty 4, Phillips) | Confirmed |
Fitment records and sources
Heat sink (qty 2, Phillips)
pitch 0.35 mm · tap 1.25 mm · clearance 1.8 mm · PH00 / Torx T4–T5
Wireless card (qty 2, Phillips)
pitch 0.35 mm · tap 1.25 mm · clearance 1.8 mm · PH00 / Torx T4–T5
Keyboard (Phillips)
pitch 0.35 mm · tap 1.25 mm · clearance 1.8 mm · PH00 / Torx T4–T5
Memory (qty 85, Phillips)
pitch 0.35 mm · tap 1.25 mm · clearance 1.8 mm · PH00 / Torx T4–T5
Keyboard (Phillips)
pitch 0.35 mm · tap 1.25 mm · clearance 1.8 mm · PH00 / Torx T4–T5
Bracket (qty 2, Phillips)
pitch 0.4 mm · tap 1.6 mm · clearance 2.4 mm · PH0 / Torx T6
Camera (qty 2, Phillips)
pitch 0.4 mm · tap 1.6 mm · clearance 2.4 mm · PH0 / Torx T6
Display (qty 9, Phillips)
pitch 0.4 mm · tap 1.6 mm · clearance 2.4 mm · PH0 / Torx T6
Fan (Phillips)
pitch 0.4 mm · tap 1.6 mm · clearance 2.4 mm · PH0 / Torx T6
Memory (qty 89, Phillips)
pitch 0.4 mm · tap 1.6 mm · clearance 2.4 mm · PH0 / Torx T6
SSD (qty 3, Phillips)
pitch 0.4 mm · tap 1.6 mm · clearance 2.4 mm · PH0 / Torx T6
Wireless card (Phillips)
pitch 0.4 mm · tap 1.6 mm · clearance 2.4 mm · PH0 / Torx T6
Bracket (qty 2, Phillips)
pitch 0.4 mm · tap 1.6 mm · clearance 2.4 mm · PH0 / Torx T6
Fan (Phillips)
pitch 0.4 mm · tap 1.6 mm · clearance 2.4 mm · PH0 / Torx T6
Hard drive (qty 2, Phillips)
pitch 0.4 mm · tap 1.6 mm · clearance 2.4 mm · PH0 / Torx T6
Hinge (qty 2, Phillips)
pitch 0.4 mm · tap 1.6 mm · clearance 2.4 mm · PH0 / Torx T6
Palm rest (Phillips)
pitch 0.4 mm · tap 1.6 mm · clearance 2.4 mm · PH0 / Torx T6
Speaker (qty 2, Phillips)
pitch 0.4 mm · tap 1.6 mm · clearance 2.4 mm · PH0 / Torx T6
System board (Phillips)
pitch 0.4 mm · tap 1.6 mm · clearance 2.4 mm · PH0 / Torx T6
Unspecified (qty 91, Phillips)
pitch 0.4 mm · tap 1.6 mm · clearance 2.4 mm · PH0 / Torx T6
Display (qty 3, Phillips)
pitch 0.45 mm · tap 2.05 mm · clearance 2.9 mm · PH1 / Torx T8
Palm rest (qty 5, Phillips)
pitch 0.45 mm · tap 2.05 mm · clearance 2.9 mm · PH1 / Torx T8
Unspecified (qty 93, Phillips)
pitch 0.45 mm · tap 2.05 mm · clearance 2.9 mm · PH1 / Torx T8
Palm rest (qty 4, Phillips)
pitch 0.45 mm · tap 2.05 mm · clearance 2.9 mm · PH1 / Torx T8
How to check the screw before you buy
- A screw that is even 1 mm too long in a laptop base can push into the keyboard, battery or a board trace, so match the length position by position.
- Diameter: across the threads an M1.6 screw measures about 1.6 mm with calipers (usually a hair under). This device also uses M2 / M2.5, so measure each screw rather than assuming they match.
- Pitch: 0.35 mm from one thread crest to the next (28.57 crests per centimetre). A thread pitch gauge or the pitch-gauge tool settles it in seconds.
- Length: measure from under the head to the tip for pan, button, wafer and cap heads; countersunk (flat) heads are measured overall.
- The records span 2.5–7 mm, which means different positions take different lengths — match each hole to its own screw.
- Driver: the source names a Phillips drive. For comparison, standard M1.6 heads take PH00 (Phillips) or T4–T5 (Torx), or a 1.5 mm hex key.
- Tightening: no device-specific torque is published in these records. The site's general figure for M1.6 is about 12-20 N·cm into metal threads and 6-10 N·cm into plastic bosses; snug it up and stop.
Common mix-ups with M1.6 / M2 / M2.5
- Headphone hinge screw sizes are usually quoted from screwdriver bit size, not an actual thread spec - measure before buying.
- M.2 SSD mounting screws (M2 x 3mm) are frequently mislabeled generically as 'M.2 screws' which can be confused with the M2 metric thread designation — they do coincide numerically here but are conceptually distinct (M.2 = card format, M2 = thread size).
- M2.5 and M3 look the same to the naked eye — you need calipers on the shank to tell them apart.
Buy these screws at TechSpare Warehouse
In stock and shipped from South Carolina. Our black screws are Phillips wafer head (low profile); match the head style and length to the original before you order.
-
M1.6 x 4mm Screws Compatible with Dell XPS 14 9440 Battery System Board 10-Pack
$4.99 -
M1.6 x 4mm Phillips Wafer Head Micro Screws LCD Shell Repair 10-Pack
$4.99
-
M2 x 3mm Screws for Dell XPS 13 9340 Base Cover SSD Shield 10-Pack Black
$4.99 -
10x M2 x 3mm Phillips Screws for Lenovo ThinkPad X131e Chromebook WiFi SSD
$4.99
-
M2.5 x 5mm Screws Compatible with Dell XPS 14 9440 Display Assembly 10-Pack
$4.99 -
M2.5 x 5mm Phillips Wafer Head Screw for Action Camera Protective Housing - Pack of 50 Black
$4.79 each · min. 2
-
ASUS ROG Strix G15 G513R Replacement Screws Sold Individually – M1.6 x 3mm, M2 x 2.5mm, M2 x 3mm, M2.5 x 6mm Phillips Wafer Head, Black
$0.10Choose size -
ASUS ROG Strix G17 G713 Replacement Screws Sold Individually – M1.6 x 3mm, M2 x 2.5mm, M2 x 3mm, M2.5 x 6mm Phillips Wafer Head, Black
$0.10Choose size
More in Laptops & PCs
The same screw also fits
Devices whose records share a thread with HP Mini 1000, closest length match first.
- Lenovo IdeaPad S740-15IRH also M2 × 3 mm
- HP 2140 also M2 × 3 mm
- HP Compaq 320 also M2 × 3 mm
- Acer Aspire 8935G also M2 × 3 mm
- Dell Inspiron 15 3530 (with USB Type-C) also M2 × 3 mm
- Lenovo ThinkPad 770 also M1.6 × 4 mm
- Lenovo ThinkPad P50s also M2 × 3 mm
- Lenovo ThinkPad P51s also M2 × 3 mm
Questions about HP Mini 1000 screws
- What size screw does HP Mini 1000 use?
- M1.6 × 2.5 mm for heat sink (qty 2, Phillips); M1.6 × 2.5 mm for wireless card (qty 2, Phillips); M1.6 × 4 mm for keyboard (Phillips); M1.6 × 4 mm for memory (qty 85, Phillips); M1.6 × 6 mm for keyboard (Phillips); M2 × 3 mm for bracket (qty 2, Phillips); M2 × 3 mm for camera (qty 2, Phillips); M2 × 3 mm for display (qty 9, Phillips); M2 × 3 mm for fan (Phillips); M2 × 3 mm for memory (qty 89, Phillips); M2 × 3 mm for SSD (qty 3, Phillips); M2 × 3 mm for wireless card (Phillips); M2 × 4.5 mm for bracket (qty 2, Phillips); M2 × 4.5 mm for fan (Phillips); M2 × 4.5 mm for hard drive (qty 2, Phillips); M2 × 4.5 mm for hinge (qty 2, Phillips); M2 × 4.5 mm for palm rest (Phillips); M2 × 4.5 mm for.
- How long are the screws in HP Mini 1000?
- The records range from 2.5 to 7 mm depending on the position, so match each screw to its own hole.
- What is the thread pitch of an M1.6 screw?
- 0.35 mm (coarse), which is the standard pitch for M1.6 machine screws; a 0.2 mm fine pitch exists but is uncommon. The tap drill is 1.25 mm and the normal clearance hole is 1.8 mm.
- What screwdriver do I need for HP Mini 1000?
- The source lists a Phillips drive. Standard M1.6 heads otherwise take PH00 (Phillips) or T4–T5 (Torx), or a 1.5 mm hex key.
- Can I use an imperial screw instead of M1.6?
- No. Imperial look-alike: #1-72 UNF (1.85 mm) is larger; there is no true imperial equivalent. Use a true M1.6 screw so it does not cross-thread or strip the hole.
- Where can I buy replacement screws for HP Mini 1000?
- TechSpareWarehouse (our own store) lists M1.6 x 4mm, M2 x 3mm and M2.5 x 5mm, which match lengths in the records above.