HP OmniBook 7 16 inch Next Gen AI PC: 16-bh0xxx screw size

HP OmniBook 7 16 inch Next Gen AI PC: 16-bh0xxx screw specifications

One row per fitment record. Head, drive are shown only where the source states them; pitch is the ISO coarse pitch for the thread.

How to check the screw before you buy

1. Laptop covers and brackets often mix two or three lengths of the same thread, so lay the screws out in the order they came out (a magnetic mat or a sheet of paper with the hole pattern drawn on it works).
2. Diameter: across the threads an M1.6 screw measures about 1.6 mm with calipers (usually a hair under). This device also uses M2 / M2.5, so measure each screw rather than assuming they match.
3. Pitch: 0.35 mm from one thread crest to the next (28.57 crests per centimetre). A thread pitch gauge or the pitch-gauge tool settles it in seconds.
4. Length: measure from under the head to the tip for pan, button, wafer and cap heads; countersunk (flat) heads are measured overall.
5. The records span 2–5 mm, which means different positions take different lengths — match each hole to its own screw.
6. Driver: the source names a Phillips drive. For comparison, standard M1.6 heads take PH00 (Phillips) or T4–T5 (Torx), or a 1.5 mm hex key.
7. Tightening: no device-specific torque is published in these records. The site's general figure for M1.6 is about 12-20 N·cm into metal threads and 6-10 N·cm into plastic bosses; snug it up and stop.

Pitch gauge · Screw size finder · Torque guide

More in Laptops & PCs

The same screw also fits

Devices whose records share a thread with HP OmniBook 7 16 inch Next Gen AI PC: 16-bh0xxx, closest length match first.

• HP ProBook 440 G6 also M2 × 2 mm
• Lenovo B570 also M2 × 3 mm
• Dell Inspiron 14 5430 also M1.6 × 2.5 mm
• Dell XPS 17 9730 also M2 × 2 mm
• Lenovo n42-20-touch also M2 × 3 mm
• HP EliteBook 8470p also M2 × 3 mm
• HP Compaq 8710p also M2 × 3 mm
• Dell Inspiron 13 7386 2-in-1 also M2 × 2 mm

Questions about HP OmniBook 7 16 inch Next Gen AI PC: 16-bh0xxx screws

What size screw does HP OmniBook 7 16 inch Next Gen AI PC: 16-bh0xxx use?

M1.6 × 2.5 mm for speaker (qty 4, Phillips); M2 × 2 mm for touchpad (qty 3, Phillips); M2 × 3 mm for I/O board (qty 3, Phillips); M2 × 3 mm for SSD (Phillips); M2 × 3 mm for system board (qty 8, Phillips); M2 × 3 mm for touchpad (qty 4, Phillips); M2 × 3 mm for wireless card (qty 1, Phillips); M2 × 3.7 mm for base cover (qty 2, Torx T5); M2 × 4.5 mm for base cover (Torx T5); M2 × 4.5 mm for battery (qty 5, Phillips); M2 × 4.5 mm for fan (qty 5, Phillips); M2.5 × 2.5 mm for hinge (qty 3, Phillips); M2.5 × 3.5 mm for hinge (qty 1, Phillips); M2.5 × 5 mm for display (qty 8, Phillips).

How long are the screws in HP OmniBook 7 16 inch Next Gen AI PC: 16-bh0xxx?

The records range from 2 to 5 mm depending on the position, so match each screw to its own hole.

What is the thread pitch of an M1.6 screw?

0.35 mm (coarse), which is the standard pitch for M1.6 machine screws; a 0.2 mm fine pitch exists but is uncommon. The tap drill is 1.25 mm and the normal clearance hole is 1.8 mm.

What screwdriver do I need for HP OmniBook 7 16 inch Next Gen AI PC: 16-bh0xxx?

The source lists a Phillips and Torx T5 drive. Standard M1.6 heads otherwise take PH00 (Phillips) or T4–T5 (Torx), or a 1.5 mm hex key.

Can I use an imperial screw instead of M1.6?

No. Imperial look-alike: #1-72 UNF (1.85 mm) is larger; there is no true imperial equivalent. Use a true M1.6 screw so it does not cross-thread or strip the hole.

Where can I buy replacement screws for HP OmniBook 7 16 inch Next Gen AI PC: 16-bh0xxx?

TechSpareWarehouse (our own store) lists M2 x 2mm, M2 x 3mm and M2.5 x 5mm, which match lengths in the records above.