How long are the screws in HP Pavilion?

The records range from 4 to 6 mm depending on the position, so match each screw to its own hole.

What is the thread pitch of an M2.5 screw?

0.45 mm (coarse), which is the standard pitch for M2.5 machine screws; a 0.35 mm fine pitch exists but is uncommon. The tap drill is 2.05 mm and the normal clearance hole is 2.9 mm.

What screwdriver do I need for HP Pavilion?

The sources do not name the drive. For M2.5, Phillips heads normally take PH1 and Torx heads T8; socket heads take a 2 mm hex key.

Can I use an imperial screw instead of M2.5?

No. Imperial look-alike: #3-48 / #4-40 (2.51 / 2.84 mm) — #4-40 is the common US stand-in and it will NOT thread in. Use a true M2.5 screw so it does not cross-thread or strip the hole.

Where can I buy replacement screws for HP Pavilion?

TechSpareWarehouse (our own store) lists M2.5 x 4mm, M2.5 x 5mm and M2.5 x 6mm, which match lengths in the records above.

HP Pavilion screw size

M2.5 · 4 to 6 mm long

The screws used on HP Pavilion are M2.5 in lengths from 4 to 6 mm.

It is listed for base cover and hinge bracket screws, black-oxide flat head.

Head and drive, as the source states them: flat / countersunk head.

This entry is marked reported and comes from techsparewarehouse.com.

For reference, M2.5 is 2.5 mm across the threads at 0.45 mm pitch. The imperial size people confuse it with: #3-48 / #4-40 (2.51 / 2.84 mm) — #4-40 is the common US stand-in and it will NOT thread in.

HP Pavilion screw specifications

One row per fitment record. Head, drive are shown only where the source states them; pitch is the ISO coarse pitch for the thread.

Thread	Length	Pitch	Head	Drive	Where it goes	Status
M2.5	4–6 mm	0.45 mm	Flat / countersunk	not stated	base cover and hinge bracket screws, black-oxide flat headblack finish	Reported

Fitment records and sources

M2.54-6mmreported

base cover and hinge bracket screws, black-oxide flat head

pitch 0.45 mm · tap 2.05 mm · clearance 2.9 mm · PH1 / Torx T8

Source

How to check the screw before you buy

Board standoffs and enclosure bosses set the usable length: the screw should clamp the board without bottoming in the standoff.
Diameter: across the threads an M2.5 screw measures about 2.5 mm with calipers (usually a hair under). If yours measures noticeably more or less, it is a different thread.
Pitch: 0.45 mm from one thread crest to the next (22.22 crests per centimetre). A thread pitch gauge or the pitch-gauge tool settles it in seconds.
Length: the source describes a countersunk (flat) head, and those are measured overall, from the top of the head to the tip.
The records span 4–6 mm, which means different positions take different lengths — match each hole to its own screw.
Driver: the source does not name the drive. Standard M2.5 heads take PH1 for Phillips and T8 for Torx, and a 2 mm hex key for socket heads; a bit that fits loosely will cam out and strip the head.
Tightening: no device-specific torque is published in these records. The site's general figure for M2.5 is about 45-70 N·cm into metal threads and 20-35 N·cm into plastic bosses; snug it up and stop.

Common mix-ups with M2.5

M2.5 pitch is 0.45mm vs M3's 0.5mm and M2's 0.4mm — forcing the wrong one strips plastic bosses instantly.
M2.5 and M3 look the same to the naked eye — you need calipers on the shank to tell them apart.

Pitch gauge · Screw size finder · Torque guide

Buy these screws at TechSpare Warehouse

In stock and shipped from South Carolina. Our black screws are Phillips wafer head (low profile); match the head style and length to the original before you order.

More in Electronics, Racks & Enclosures

19-inch rack cage nut (light equipment)19-inch rack cage nut (metric square-hole rails)19-inch rack cage nut (mid size)19-inch rack cage nut and panel screw 19-inch rack network and AV gear 19-inch rack-mount audio/AV equipment 19-inch server racks 19in / 10in server rack cage nut and screw kit 19in equipment rack (Kendall Howard cage nuts)19in rack cage nuts (alternate metric)19in rack cage nuts (metric)1U rack-mount PDU (American Denki)

Browse all 357 in Electronics, Racks & Enclosures →

The same screw also fits

Devices whose records share a thread with HP Pavilion, closest length match first.

PW-Sat2 CubeSat secondary structure and panels also M2.5 × 4–6 mm
HP EliteBook 840 G2 / 740 G2 / ZBook 14 G2 also M2.5 × 4–5 mm
HP EliteBook 725 G3 also M2.5 × 4–5 mm
Keystone Electronics metric nylon standoff also M2.5 × 4–5 mm
Eurorack rails (older Doepfer variant) also M2.5 × 6 mm
Wurth Elektronik WA-SPAIE plastic spacer stud also M2.5 × 5–6 mm
Lenovo IdeaPad also M2.5 × 4–6 mm
Clear-Com panel PSU module also M2.5 × 5 mm

Questions about HP Pavilion screws

What size screw does HP Pavilion use?: M2.5 × 4–6 mm for base cover and hinge bracket screws, black-oxide flat head.
How long are the screws in HP Pavilion?: The records range from 4 to 6 mm depending on the position, so match each screw to its own hole.
What is the thread pitch of an M2.5 screw?: 0.45 mm (coarse), which is the standard pitch for M2.5 machine screws; a 0.35 mm fine pitch exists but is uncommon. The tap drill is 2.05 mm and the normal clearance hole is 2.9 mm.
What screwdriver do I need for HP Pavilion?: The sources do not name the drive. For M2.5, Phillips heads normally take PH1 and Torx heads T8; socket heads take a 2 mm hex key.
Can I use an imperial screw instead of M2.5?: No. Imperial look-alike: #3-48 / #4-40 (2.51 / 2.84 mm) — #4-40 is the common US stand-in and it will NOT thread in. Use a true M2.5 screw so it does not cross-thread or strip the hole.
Where can I buy replacement screws for HP Pavilion?: TechSpareWarehouse (our own store) lists M2.5 x 4mm, M2.5 x 5mm and M2.5 x 6mm, which match lengths in the records above.

Heads up: shipping delay