HP Pavilion 5300 screw size
M2 / M2.5 / M3 / M5 · 3 to 10 mm long
Our records put HP Pavilion 5300 on M2, M2.5, M3 and M5 screws in lengths from 3 to 10 mm.
There are 23 separate fitment records for it, including display bezel (qty 1) (M2), unspecified (qty 2, flat) (M2) and system board (qty 2) (M2), plus 20 more in the table below.
Head and drive, as the sources state them: shoulder screw head.
23 of the 23 records are marked confirmed, drawn from 1 source (tim.id.au).
For reference, M2 is 2 mm across the threads at 0.4 mm pitch. The imperial size people confuse it with: #2-56 UNC (2.18 mm) is close but not interchangeable.
HP Pavilion 5300 screw specifications
One row per fitment record. Head, drive are shown only where the source states them; pitch is the ISO coarse pitch for the thread.
| Thread | Length | Pitch | Head | Drive | Where it goes | Status |
|---|---|---|---|---|---|---|
| M2 | 3 mm | 0.4 mm | not stated | not stated | Display bezel (qty 1) | Confirmed |
| M2 | 3 mm | 0.4 mm | not stated | not stated | Unspecified (qty 2, flat) | Confirmed |
| M2 | 4 mm | 0.4 mm | not stated | not stated | System board (qty 2) | Confirmed |
| M2 | 5 mm | 0.4 mm | not stated | not stated | Heat sink (qty 4) | Confirmed |
| M2 | 5 mm | 0.4 mm | not stated | not stated | System board (qty 2) | Confirmed |
| M2.5 | 4 mm | 0.45 mm | not stated | not stated | Hard drive (qty 2) | Confirmed |
| M2.5 | 4 mm | 0.45 mm | not stated | not stated | Heat sink (qty 3) | Confirmed |
| M2.5 | 4 mm | 0.45 mm | not stated | not stated | Keyboard (qty 4) | Confirmed |
| M2.5 | 4 mm | 0.45 mm | not stated | not stated | Palm rest (qty 4) | Confirmed |
| M2.5 | 4 mm | 0.45 mm | not stated | not stated | System board (qty 4) | Confirmed |
| M2.5 | 4 mm | 0.45 mm | not stated | not stated | Unspecified (qty 2) | Confirmed |
| M2.5 | 4 mm | 0.45 mm | not stated | not stated | Wireless card | Confirmed |
| M2.5 | 6 mm | 0.45 mm | not stated | not stated | Display (qty 6) | Confirmed |
| M2.5 | 6 mm | 0.45 mm | not stated | not stated | Display bezel (qty 4) | Confirmed |
| M2.5 | 6 mm | 0.45 mm | not stated | not stated | Hard drive | Confirmed |
| M2.5 | 6 mm | 0.45 mm | not stated | not stated | Optical drive (qty 3) | Confirmed |
| M2.5 | 6 mm | 0.45 mm | not stated | not stated | Palm rest (qty 16) | Confirmed |
| M2.5 | 6 mm | 0.45 mm | not stated | not stated | Speaker (qty 1) | Confirmed |
| M2.5 | 6 mm | 0.45 mm | not stated | not stated | System board (qty 3) | Confirmed |
| M2.5 | 6 mm | 0.45 mm | not stated | not stated | Unspecified (qty 3) | Confirmed |
| M2.5 | 7 mm | 0.45 mm | not stated | not stated | Palm rest (qty 16) | Confirmed |
| M3 | 4 mm | 0.5 mm | not stated | not stated | Hard drive (qty 4) | Confirmed |
| M5 | 10 mm | 0.8 mm | Shoulder screw | not stated | System board (qty 4, shoulder) | Confirmed |
Fitment records and sources
Display bezel (qty 1)
pitch 0.4 mm · tap 1.6 mm · clearance 2.4 mm · PH0 / Torx T6
Unspecified (qty 2, flat)
pitch 0.4 mm · tap 1.6 mm · clearance 2.4 mm · PH0 / Torx T6
System board (qty 2)
pitch 0.4 mm · tap 1.6 mm · clearance 2.4 mm · PH0 / Torx T6
Heat sink (qty 4)
pitch 0.4 mm · tap 1.6 mm · clearance 2.4 mm · PH0 / Torx T6
System board (qty 2)
pitch 0.4 mm · tap 1.6 mm · clearance 2.4 mm · PH0 / Torx T6
Hard drive (qty 2)
pitch 0.45 mm · tap 2.05 mm · clearance 2.9 mm · PH1 / Torx T8
Heat sink (qty 3)
pitch 0.45 mm · tap 2.05 mm · clearance 2.9 mm · PH1 / Torx T8
Keyboard (qty 4)
pitch 0.45 mm · tap 2.05 mm · clearance 2.9 mm · PH1 / Torx T8
Palm rest (qty 4)
pitch 0.45 mm · tap 2.05 mm · clearance 2.9 mm · PH1 / Torx T8
System board (qty 4)
pitch 0.45 mm · tap 2.05 mm · clearance 2.9 mm · PH1 / Torx T8
Unspecified (qty 2)
pitch 0.45 mm · tap 2.05 mm · clearance 2.9 mm · PH1 / Torx T8
Wireless card
pitch 0.45 mm · tap 2.05 mm · clearance 2.9 mm · PH1 / Torx T8
Display (qty 6)
pitch 0.45 mm · tap 2.05 mm · clearance 2.9 mm · PH1 / Torx T8
Display bezel (qty 4)
pitch 0.45 mm · tap 2.05 mm · clearance 2.9 mm · PH1 / Torx T8
Hard drive
pitch 0.45 mm · tap 2.05 mm · clearance 2.9 mm · PH1 / Torx T8
Optical drive (qty 3)
pitch 0.45 mm · tap 2.05 mm · clearance 2.9 mm · PH1 / Torx T8
Palm rest (qty 16)
pitch 0.45 mm · tap 2.05 mm · clearance 2.9 mm · PH1 / Torx T8
Speaker (qty 1)
pitch 0.45 mm · tap 2.05 mm · clearance 2.9 mm · PH1 / Torx T8
System board (qty 3)
pitch 0.45 mm · tap 2.05 mm · clearance 2.9 mm · PH1 / Torx T8
Unspecified (qty 3)
pitch 0.45 mm · tap 2.05 mm · clearance 2.9 mm · PH1 / Torx T8
Palm rest (qty 16)
pitch 0.45 mm · tap 2.05 mm · clearance 2.9 mm · PH1 / Torx T8
Hard drive (qty 4)
pitch 0.5 mm · tap 2.5 mm · clearance 3.4 mm · PH1 / Torx T10
System board (qty 4, shoulder)
pitch 0.8 mm · tap 4.2 mm · clearance 5.5 mm · PH2 / Torx T25
How to check the screw before you buy
- A screw that is even 1 mm too long in a laptop base can push into the keyboard, battery or a board trace, so match the length position by position.
- Diameter: across the threads an M2 screw measures about 2 mm with calipers (usually a hair under). This device also uses M2.5 / M3 / M5, so measure each screw rather than assuming they match.
- Pitch: 0.4 mm from one thread crest to the next (25 crests per centimetre). A thread pitch gauge or the pitch-gauge tool settles it in seconds.
- Length: for shoulder screw screws, measure from under the head to the tip (countersunk heads are the exception: they are measured overall).
- The records span 3–10 mm, which means different positions take different lengths — match each hole to its own screw.
- Driver: the source does not name the drive. Standard M2 heads take PH0 for Phillips and T6 for Torx, and a 1.5 mm hex key for socket heads; a bit that fits loosely will cam out and strip the head.
- Tightening: no device-specific torque is published in these records. The site's general figure for M2 is about 25-40 N·cm into metal threads and 12-20 N·cm into plastic bosses; snug it up and stop.
Common mix-ups with M2 / M2.5 / M3 / M5
- M.2 SSD mounting screws (M2 x 3mm) are frequently mislabeled generically as 'M.2 screws' which can be confused with the M2 metric thread designation — they do coincide numerically here but are conceptually distinct (M.2 = card format, M2 = thread size).
- M2.5 and M3 look the same to the naked eye — you need calipers on the shank to tell them apart.
- 3.5in desktop and enterprise hard drives are 6-32 UNC imperial, not M3 - only the 2.5in form factor is metric.
- Ski and snowboard binding screws vary by brand and insert system (4x4, Channel, Tyrolia, Marker). Aftermarket suppliers standardise on M5/M6 but OEM screws can be a different pitch.
Buy these screws at TechSpare Warehouse
In stock and shipped from South Carolina. Our black screws are Phillips wafer head (low profile); match the head style and length to the original before you order.
-
M2 x 3mm Screws for Dell XPS 13 9340 Base Cover SSD Shield 10-Pack Black
$4.99 -
10x M2 x 3mm Phillips Screws for Lenovo ThinkPad X131e Chromebook WiFi SSD
$4.99
-
M2 x 4mm Phillips Wafer Head Machine Screws Black 50-Pack Laptop SSD Repair
$4.49 each · min. 2
-
M2 x 4mm Screws for Dell Latitude 5530 SSD Type-C Bracket 10-Pack Black
$4.99
-
M2 x 5mm Replacement Bottom Case Screws for Dell Inspiron 3535 Laptop 10-Pack
$4.99 -
M2 x 5mm Phillips Wafer Head Screw for Dell G16 7630 Gaming Laptop Repair - Pack of 100 Black
$7.99 -
ASUS ROG Strix G15 G513R Replacement Screws Sold Individually – M1.6 x 3mm, M2 x 2.5mm, M2 x 3mm, M2.5 x 6mm Phillips Wafer Head, Black
$0.10Choose size -
ASUS ROG Strix G17 G713 Replacement Screws Sold Individually – M1.6 x 3mm, M2 x 2.5mm, M2 x 3mm, M2.5 x 6mm Phillips Wafer Head, Black
$0.10Choose size
More in Laptops & PCs
The same screw also fits
Devices whose records share a thread with HP Pavilion 5300, closest length match first.
- Dell Inspiron 17 3781 also M2 × 3 mm
- Dell Latitude 7320 2-in-1 also M2 × 3 mm
- HP Compaq Presario X1000 also M2 × 3 mm
- HP Presario 2800 also M2 × 4 mm
- HP OmniBook 7 14 inch PC: 14- fs0xxx also M2 × 3 mm
- Lenovo ThinkPad X22 also M2 × 3 mm
- HP ProBook 4411s also M2 × 3 mm
- HP ProBook 4410s also M2 × 3 mm
Questions about HP Pavilion 5300 screws
- What size screw does HP Pavilion 5300 use?
- M2 × 3 mm for display bezel (qty 1); M2 × 3 mm for unspecified (qty 2, flat); M2 × 4 mm for system board (qty 2); M2 × 5 mm for heat sink (qty 4); M2 × 5 mm for system board (qty 2); M2.5 × 4 mm for hard drive (qty 2); M2.5 × 4 mm for heat sink (qty 3); M2.5 × 4 mm for keyboard (qty 4); M2.5 × 4 mm for palm rest (qty 4); M2.5 × 4 mm for system board (qty 4); M2.5 × 4 mm for unspecified (qty 2); M2.5 × 4 mm for wireless card; M2.5 × 6 mm for display (qty 6); M2.5 × 6 mm for display bezel (qty 4); M2.5 × 6 mm for hard drive; M2.5 × 6 mm for optical drive (qty 3); M2.5 × 6 mm for palm rest (qty 16); M2.5 × 6 mm for speaker (qty 1); M2.5 × 6 mm for system board (qty 3); M2.5 × 6 mm for unspecifi.
- How long are the screws in HP Pavilion 5300?
- The records range from 3 to 10 mm depending on the position, so match each screw to its own hole.
- What is the thread pitch of an M2 screw?
- 0.4 mm (coarse), which is the standard pitch for M2 machine screws; a 0.25 mm fine pitch exists but is uncommon. The tap drill is 1.6 mm and the normal clearance hole is 2.4 mm.
- What screwdriver do I need for HP Pavilion 5300?
- The sources do not name the drive. For M2, Phillips heads normally take PH0 and Torx heads T6; socket heads take a 1.5 mm hex key.
- Can I use an imperial screw instead of M2?
- No. Imperial look-alike: #2-56 UNC (2.18 mm) is close but not interchangeable. Use a true M2 screw so it does not cross-thread or strip the hole.
- Where can I buy replacement screws for HP Pavilion 5300?
- TechSpareWarehouse (our own store) lists M2 x 3mm, M2 x 4mm and M2 x 5mm, which match lengths in the records above.